Page 1
INSTALLATION INSTRUCTIONS
Product
7160-1084
GETAC K120 TABLET DOCKING STATION
Revision
Rev. B
Form
INST-835
Printing Spec:
PS-001
This instruction sheet is for the Getac K120 Tablet docking station only. For instructions on
features, set-up, and operation of the computer, please refer to the manual provided by
Getac with the computer.
This docking station is designed to be used with a variety of Gamber-Johnson mounting
systems. Installation instructions for other Gamber-Johnson products are provided with each
individual product.
This instruction sheet is for the following products:
Item No. 7160-1084-00
Item No. 7160-1084-03
No RF (External Power Supply sold separately)
Tri RF (External Power Supply sold separately)
Getac recommends using the following Power Adapters to power the docking station. They
can be ordered from Gamber-Johnson seperately.
17057
16079
16078
16513
- Auto (12-32 Vdc input) - Available with the docking station as KIT 7170-0694
- Isolated (12-32 Vdc input)
- Isolated (20-60 Vdc input)
- Isolated (72-110 Vdc input)
Product Mounting Disclaimer
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868
1 / 6
Page 2
PRE-INSTALLATION RECOMMENDATIONS
Conduct a "Bench Test"
Gamber-Johnson strongly advises a "bench test" be conducted to verify all electronic and
software issues are resolved prior to installation:
Make sure the computer is operational by itself.
1.
Insert computer into the docking station and verify that the computer is
2.
operating in the dock.
Interconnect entire assembly and verify start-up of all components, including
3.
other equipment (printers, modems, scanners, etc.)
Gamber-Johnson recommends positioning of all mounts and equipment in the vehicle
prior to the actual install to verify that mounting locations are safe and practical.
IMPORTANT SAFETY INFORMATION FOR INSTALLERS
Safety is dependent on the proper installation and servicing of this docking station. It is
important to read and follow all instructions before installing this product.
To properly install a Gamber-Johnson docking station you must have a good understanding of
automotive electrical procedures and systems, along with proficiency in the installation and
service of aftermarket vehicle equipment.
There are no adjustments required at any time of the electrical components within the docking
station.
During Installation:
DO NOT
DO NOT
When drilling into the vehicle, DO make sure that both sides of the surface are clear of
anything that could be damaged.
CAUTION:
Opening the docking station will void the product warranty.
connect this docking station to the vehicle battery until:
All other electrical connections are made
1.
Mounting of all components is complete
2.
Verification that no shorts exist in the entire system
3.
install equipment or route wires or cords in the deployment path of any air bag.
If wiring is shorted to the frame, high current conductors can cause hazardous
sparks resulting in electrical fires or flying molten metal.
After installation:
Test the docking station to ensure that it is working properly.
File these instructions in a safe place and refer to them when performing maintenance or reinstalling.
WARNING
: Failure to follow all safety precautions and instructions may result in property
damage, serious injury, or death.
2 / 6
Page 3
Upper Walls
Provides docking guidance and
connector protection, prevents
mis-docking
Lower Walls
FEATURE IDENTIFICATION
Slam Latch
Release Button
Barrel Key Lock
Guide Pins
External Antenna - Tri RF
(Optional)
Docking Connector
Port Indentification
(Ports, see page 4)
Part#/Serial# Label
(2) USB 2.0
(Fast Charging)
1500 mA
VESA 75mm Hole Pattern
1/4-20 x 0.500" hardware provided
External Antenna - SMA
(WiFi, GPS, CELL)
(Optional)
3 / 6
Page 4
PORT IDENTIFICATION
Power Input: 19 Vdc
Serial
Ethernet (2)
(RJ45)
USB3.0 (2)
USB3.0
(Fast Charging)
1500 mA
900 mA
USB2.0
500 mA
HDMI
VGA
CABLE MANAGMENT FEATURES AND PROPER INSTALLATION
1.) Use Zip ties (provided) to secure each port cable to the specific strain relief feature on the dock
2.) Use Zip ties (provided) to secure bundled cables for improved routing - OPTIONAL
1.) Cable Tie Slots
(Port Specific)
Power
2.) Cable Tie Slots (4)
(Extra)
Ethernet
Ethernet
USB (2)
USB (2)
HDMI
Optional
Power
Cable
Routing
Cables route past mounting equipment
4 / 6
Page 5
DOCKING AND UNDOCKING THE COMPUTER
OPERATION - DOCKING
1. Insert the bottom of the tablet
into the bottom cavity of the
dock. The walls on the dock will
guide the tablet into place.
2. Rotate the top of the tablet
into the dock, overcoming the
resistance until the Release
Button returns to the "Latched"
position. The slam latch will
come over the front of the tablet.
There will also be an audible
confirmation as the latch system
springs downward.
3. Optional - With the dock in the
"Latched" position, turn the lock
to the "LOCKED" position (CW).
"Latched" Position
Rotate Top
Insert Bottom First
"Locked" Position
OPERATION - UNDOCKING
1. Turn the lock to the
"UNLOCKED" position (CCW).
2. With your hand on the top of
the tablet, push up on the blue
Release Button until the
computer is free to move forward.
While the dock is "Un-Latched",
pull the top of the tablet forward
until it clears the dock. This can
be done right or left handed.
3. Remove the computer by
pulling it away from the dock.
"Un-Locked" Position
5 / 6
Page 6
Regulatory Certification Information
Regulatory Model #: 7160-1084
GJ Model #'s & Description:
7160-1084-00 Dock-Getac K120 Tablet-No RF
7160-1084-03 Dock-Getac K120 Tablet-Tri RF
Certifications:
EN 55032: 2012/AC: 2013 Class B
•
EN 50498:2010
•
E-mark
•
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions. (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Gamber-Johnson LLC, 3001 Borham Ave.,
Stevens Point, WI, 54481, USA, 715-344-3482
6 / 6
Loading...