Page 1
INSTALLATION INSTRUCTIONS
Product
7160-0909
PANASONIC CF33 LAPTOP DOCKING STATION
Revision
Rev. C
Form
INST-761
Printing Spec:
PS-001
This instruction sheet is for the Panasonic CF33 Laptop docking station only. For
instructions on features, set-up, and operation of the computer, please refer to
the manual provided by Panasonic with the computer.
This docking station is designed to be used with a variety of Gamber-Johnson
mounting systems. Installation instructions for other Gamber-Johnson products
are provided with each individual product.
This instruction sheet is for the following products:
Item No. 7160-0909-00
Item No. 7160-0909-02
Item No. 7160-0909-12
No RF (External Power Supply sold separately)
Dual RF, Right (External Power Supply sold separately)
Dual RF, Left (External Power Supply sold separately)
Panasonic recommends using a Lind Auto Adapter to power the docking station. It
can be ordered from Gamber-Johnson (Item No. 14103 for bare wire leads, Item
No. 14650 for mountable case and cigerette plug lead).
Product Mounting Disclaimer
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868
1 / 5
Page 2
PRE-INSTALLATION RECOMMENDATIONS
Conduct a "Bench Test"
Gamber-Johnson strongly advises a "bench test" be conducted to verify all
electronic and software issues are resolved prior to installation:
Make sure the computer is operational by itself.
1.
Insert computer into the docking station and verify that the computer is
2.
operating in the dock.
Interconnect entire assembly and verify start-up of all components,
3.
including other equipment (printers, modems, scanners, etc.)
Gamber-Johnson recommends positioning of all mounts and equipment in the
vehicle prior to the actual install to verify that mounting locations are safe and
practical.
IMPORTANT SAFETY INFORMATION FOR INSTALLERS
Safety is dependent on the proper installation and servicing of this docking station. It is
important to read and follow all instructions before installing this product.
To properly install a Gamber-Johnson docking station you must have a good
understanding of automotive electrical procedures and systems, along with proficiency
in the installation and service of aftermarket vehicle equipment.
There are no adjustments required at any time of the electrical components within the
docking station.
During Installation:
DO NOT
DO NOT
When drilling into the vehicle, DO make sure that both sides of the surface are clear of
anything that could be damaged.
CAUTION:
connect this docking station to the vehicle battery until:
All other electrical connections are made
1.
Mounting of all components is complete
2.
Verification that no shorts exist in the entire system
3.
install equipment or route wires or cords in the deployment path of any air bag.
If wiring is shorted to the frame, high current conductors can cause
Opening the docking station will void the product warranty.
hazardous sparks resulting in electrical fires or flying molten metal.
After installation:
Test the docking station to ensure that it is working properly.
File these instructions in a safe place and refer to them when performing maintenance
or re-installing.
WARNING
: Failure to follow all safety precautions and instructions may result in property
damage, serious injury, or death.
2 / 5
Page 3
PANASONIC CF33 LAPTOP DOCK FEATURE IDENTIFICATION
Screen Support mount location
(Sold Seperately as 7110-1214)
Mounts to either side, or both
Rear Guide Pins
Computer Power
Input Blocker
Stability Pads
Ground/Eject Pins
Front Guide Pins
VESA 75mm Hole Pattern
M6 x 50mm hardware provided
(2) USB 2.0
Handle Anti-Rattle Pads
Barrel Latch
Docking Connector
Dual RF Connector
(Optional)
Lock Fin
Prevents Tablet
detach from
Keyboard
Barrel
Key
Lock
Computer USB
Port Blocker
Release Button
(User Interface)
Contact friendly edges
Cable Tie Slots
(Port Specific)
Power Input:
15.6 Vdc
External ANT
Switch
RF - ANT 1
RF - ANT 2
(-02 SKU, Right)
Cable Tie Slots
(Extra)
Part#/Serial# Label
Front Grab
Port Identification
Markings
Serial (RS232)
VGA
HDMI
(2) USB 2.0
(2) USB 3.0
Warranty Label
(2) Ethernet (RJ45)
RF - ANT 1 & 2
(-12 SKU, Left)
3 / 5
Page 4
DOCKING AND UNDOCKING THE COMPUTER
TO DOCK THE COMPUTER
1. Insert the front of the computer into the front blue guide pins of the dock. Arrows on the
dock point to the direction of installation. The round corner walls and plastic features will
guide the computer into place.
2. Rotate the rear of the computer onto the dock, squeeze on both corners, overcoming the
resistance until the Release Button returns to the "Latched" position. The grooves on the button
line up with the lower groove on the dock. There will also be an audible confirmation as the
latch system springs downward.
3. With the dock in the "Latched" position, turn the lock to the "LOCKED" position (Clockwise).
The Lock Fin will move upward and block the tablet release button on the computer.
Squeeze
both corners
Insert Front First
TO UNDOCK THE COMPUTER
1. Turn the lock to the "UNLOCKED" position (Counter Clockwise). The Lock Fin will spring down.
2. Push up on the blue Release Button until the computer springs upward. There will be an
audible recognition as well. At this point, the computer is free to be removed.
3. Remove the computer by pulling it away from the dock.
Dock "Latched"
4 / 5
Page 5
Regulatory Certification Information
Regulatory Model #: 7160-0909
GJ Model #'s & Description:
7160-0909-00 Dock-Panasonic CF33 Laptop-No RF
7160-0909-02 Dock-Panasonic CF33 Laptop-Dual RF, Right
7160-0909-12 Dock-Panasonic CF33 Laptop-Dual RF, Left
Certifications:
EN 55032: 2012/AC: 2013 Class A
•
EN 50498:2010
•
EN 50581:2012
•
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions. (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Gamber-Johnson LLC, 3001 Borham Ave.,
Stevens Point, WI, 54481, USA, 715-344-3482
5 / 5
Loading...