Gamber Johnson 7160-0907-02, 7160-0907-00, 7160-0907-06, 7160-0907-07 Installation Instructions Manual

INSTALLATION INSTRUCTIONS

Product

7160-0907

Revision

Rev. B

PANASONIC CF33 TABLET DOCKING STATION

Printing Spec:

Form

INST-759

PS-001

This instruction sheet is for the Panasonic CF33 Tablet docking station only. For
instructions on features, set-up, and operation of the computer, please refer to the
manual provided by Panasonic with the computer.

This docking station is designed to be used with a variety of Gamber-Johnson
mounting systems. Installation instructions for other Gamber-Johnson products are
provided with each individual product.

This instruction sheet is for the following products:

Item No. 7160-0907-00 FULL PCB, No RF (External Power Supply sold separately)
Item No. 7160-0907-02 FULL PCB, Dual RF, Right (External Power Supply sold separately)
Item No. 7160-0907-06 LITE PCB, NO RF (External Power Supply sold separately)
Item No. 7160-0907-07 LITE PCB, Dual RF (External Power Supply sold separately)

Panasonic recommends using a Lind Auto Adapter to power the docking station. It can be ordered from
Gamber-Johnson (Item No. 14103 for bare wire leads, Item No. 14650 for mountable case and cigarette
plug lead).

Product Mounting Disclaimer

Product Mounting Disclaimer
Gamber-John son is not liable under any theo ry of contra ct or tort law for any loss, da mage, personal injury, special, incidental or consequential damages for pe rsonal injury o r other damage

Gamber-John son is not liable under any theo ry of contra ct or tort law for any loss, da mage, personal injury, special, incidental or consequential damages for pe rsonal injury o r other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in ve hicle or any other application. I n order to safely install and u se Gamber-J ohnson

of any nature arising directly or indirectly as a result of the improper installation or use of its products in ve hicle or any other application. I n order to safely install and u se Gamber-J ohnson
products full consideration of vehicle occupants, vehicle sy stems (i.e., the location of fuel lines, brakes lines, electrical, dr ive train or othe r systems), air-bags and other safety equipment is

products full consideration of vehicle occupants, vehicle sy stems (i.e., the location of fuel lines, brakes lines, electrical, dr ive train or othe r systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically dis claims any res ponsibility for the improper use or installation of its products not c onsistent with the original vehicle manufactures specifications

required. Gamber-Johnson specifically dis claims any res ponsibility for the improper use or installation of its products not c onsistent with the original vehicle manufactures specifications
and recommen dations, Gamber-Johnson p roduct instruction sheets, or workmanship standards as endorsed through the Gambe r-Johnson Certified Installer Program.

and recommen dations, Gamber-Johnson p roduct instruction sheets, or workmanship standards as endorsed through the Gambe r-Johnson Certified Installer Program.

© Copyright 2017 Gamber-Johnson, LLC

If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868

1 / 6

PRE-INSTALLATION RECOMMENDATIONS

Conduct a "Bench Test"

Gamber-Johnson strongly advises a "bench test" be conducted to verify all
electronic and software issues are resolved prior to installation:

Make sure the computer is operational by itself.1.
Insert computer into the docking station and verify that the computer is 2.
operating in the dock.
Interconnect entire assembly and verify start-up of all components, 3.
including other equipment (printers, modems, scanners, etc.)

Gamber-Johnson recommends positioning of all mounts and equipment in the
vehicle prior to the actual install to verify that mounting locations are safe and
practical.

IMPORTANT SAFETY INFORMATION FOR INSTALLERS

Safety is dependent on the proper installation and servicing of this docking station. It is
important to read and follow all instructions before installing this product.

To properly install a Gamber-Johnson docking station you must have a good
understanding of automotive electrical procedures and systems, along with proficiency
in the installation and service of aftermarket vehicle equipment.

There are no adjustments required at any time of the electrical components within the
docking station. Opening the docking station will void the product warranty.

During Installation:

DO NOT connect this docking station to the vehicle battery until:

All other electrical connections are made1.
Mounting of all components is complete2.
Verification that no shorts exist in the entire system3.

DO NOT install equipment or route wires or cords in the deployment path of any air bag.

When drilling into the vehicle, DO make sure that both sides of the surface are clear of
anything that could be damaged.

CAUTION:

hazardous sparks resulting in electrical fires or flying molten metal.

After installation:

If wiring is shorted to the frame, high current conductors can cause

Test the docking station to ensure that it is working properly.

File these instructions in a safe place and refer to them when performing maintenance
or re-installing.

WARNING

damage, serious injury, or death.

: Failure to follow all safety precautions and instructions may result in property

2 / 6

PANASONIC CF33 TABLET DOCK FEATURE IDENTIFICATION

Lock

Latch

VESA 75MM
Hole Pattern

Connector Guard

(2) USB 2.0

(2) USB 3.0

Power Input

15.6 Vdc

(2) USB 2.0

External ANT
Switch

Part# / Serial# Label

HDMI
Serial (RS232)

Warranty Label

Cable Tie Slot
(for power)

(2) Ethernet (RJ45)

RF - ANT 1

Cable Tie Slots

VGA

RF - ANT 2

NOTE: "LITE" version dock will not have VGA and HDMI ports

3 / 6

ATTACHING THE HAND STRAP TO THE TABLET

The Dock will accommodate tablet with hand strap or extended battery module but not both.

Below is the correct way to attach the hand strap to the tablet so that it functions properly
with the docking station.

Step 1: Leave at least .250"
space between the edge
of the tablet and the hand strap
edge.

Step 2: Make sure that the
plastic clips do NOT run over the
outline of the hand strap.

Step 3: The strap/clip on the
bottom should be tight.

Below is an example for INCORRECT way to attach the hand strap to the tablet.

Figure 1 Figure 2

Figure 1: Plastic clip run over the outline of the laptop

Figure 2: Plastic clip run over the outline of the laptop
and No space between edge of the tablet and edge
of the hand strap

Figure 3

Figure 3: The clip/strap on the bottom is loose

4 / 6

DOCKING AND UNDOCKING THE TABLET

TO DOCK THE TABLET

1. Turn the tablet off.

2. Gently insert the bottom of the tablet into the docking station and push it down. The two
ribs in the dock will guide the tablet into the correct position.

2. Gently rotate the top of the tablet into the dock until latch spring down and holds tablet in
place.

3. Turn the tablet on for use.

4. (Optional) Turn the key to "LOCKED" position (counter clockwise) for security purpose.

Push inward

Dock "Latched"

Insert Bottom First

TO UNDOCK THE TABLET

1. Turn the key to the "UNLOCKED" position (Clockwise).

2. Push upward on the blue thumb knob and pull outward on the tablet until the tablet clears
the latch portion of the dock.

3. Lift the tablet vertically upwards and remove it from the dock.

Push up the Latch Push outward

5 / 6

Regulatory Certification Information

Regulatory Model #: 7160-0907

GJ Model #'s & Description:

7160-0907-00 Dock-Panasonic CF33 Tablet- Full PCB - No RF
7160-0907-02 Dock-Panasonic CF33 Tablet- Full PCB - Dual RF
7160-0907-06 Dock-Panasonic CF33 Tablet- Lite PCB - No RF
7160-0907-07 Dock-Panasonic CF33 Tablet- Lite PCB - Dual RF

Certifications:

EN 55032: 2012/AC: 2013 Class B•
EN 50498:2010•
EN 50581:2012•

This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions. (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.

Gamber-Johnson LLC, 3001 Borham Ave.,
Stevens Point, WI, 54481, USA, 715-344-3482

6 / 6