Gamber Johnson 7160-0902-00-P, 7160-0902-00-E, 7160-0902-02-E, 7160-0902-04, 7160-0902-05 Installation Instructions Manual

INSTALLATION INSTRUCTIONS

Product

7160-0902

PANASONIC FZA2 THICKDOCK

Revision

Rev.B

Form

INST-755

Printing Spec:

PS-001

This instruction sheet is for the Panasonic FZA2 DOCK only. For instructions on
features, set-up, and operation of the computer, please refer to the manual
provided by Panasonic with the computer.

This docking station is designed to be used with a variety of Gamber-Johnson
mounting systems. Installation instructions for other Gamber-Johnson products
are provided with each individual product.

This instruction sheet is for the following products:

Item No. 7160-0902-00(-P)(-E), 7160-0902-02(-P)(-E), 7160-0902-04, & 7160-0902-05

Product Mounting Disclaimer

Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage

Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson

of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is

products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications

required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.

and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.

If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868

PRE-INSTALLATION RECOMMENDATIONS

Conduct a "Bench Test"

Gamber-Johnson strongly advises a "bench test" be conducted to verify all
electronic and software issues are resolved prior to installation:

Make sure the computer is operational by itself.

1.
Insert computer into the docking station and verify that the computer is

2.
operating in the dock.
Interconnect entire assembly and verify start-up of all components,

3.
including other equipment (printers, modems, scanners, etc.)

Gamber-Johnson recommends positioning of all mounts and equipment in the
vehicle prior to the actual install to verify that mounting locations are safe and
practical.

IMPORTANT SAFETY INFORMATION FOR INSTALLERS

Safety is dependent on the proper installation and servicing of this docking station. It is
important to read and follow all instructions before installing this product.

To properly install a Gamber-Johnson docking station you must have a good
understanding of automotive electrical procedures and systems, along with proficiency
in the installation and service of aftermarket vehicle equipment.

There are no adjustments required at any time of the electrical components within the
docking station.

During Installation:

DO NOT

DO NOT

When drilling into the vehicle, DO make sure that both sides of the surface are clear of
anything that could be damaged.

CAUTION:

connect this docking station to the vehicle battery until:

All other electrical connections are made

1.
Mounting of all components is complete

2.
Verification that no shorts exist in the entire system

3.

install equipment or route wires or cords in the deployment path of any air bag.

If wiring is shorted to the frame, high current conductors can cause

Opening the docking station will void the product warranty.

hazardous sparks resulting in electrical fires or flying molten metal.

After installation:

Test the docking station to ensure that it is working properly.

File these instructions in a safe place and refer to them when performing maintenance
or re-installing.

WARNING

: Failure to follow all safety precautions and instructions may result in property

damage, serious injury, or death.

2 / 5

PANASONIC FZA2 DOCK FEATURE IDENTIFICATION

Keylock

Release button

DC-IN Jack (DC-IN 16V)

External Antenna Select Switch

EXT_AN T1

VESA 75 mm STUDS

2x USB 2.0 ports

LAN Port

EXT_AN T2

3 / 5

DOCKING AND UNDOCKING THE COMPUTER

3.

1.

2.

DOCKING PROCEDURE

1.Insert FZ-A2 into the vehicle mounter as shown

2.Ensure the bottom of the FZ-Z2 is located in the vehicle mounter

3.Push the top of the locking mechanism (slightly press release button assist)

4.

Unlocked

5.

UNDOCKING PROCEDURE

4.Ensure the lock is in the unlocked position.

5.Push the release button.

6.Remove the FZ-A2 from the dock

NOTE:

Portions of your car mounter may differ somewhat from the illustrations in the operation instructions,
but this should present no problems in actual use. Be sure to follow the operating instructions
when using your car mounter.

Locked

6.

5.

4 / 5

Regulatory Certification Information

Regulatory Model #: 7160-0902

GJ Model #'s & Description:
7160-0902-00 (-P)(-E) DOCK-PANASONIC-FZA2 THICK NO RF KEYED ALIKE
7160-0902-02 (-P)(-E) DOCK-PANASONIC-FZA2 THICK DUAL RF KEYED ALIKE
7160-0902-04 DOCK-PANASONIC-FZA2 THICK NO RF KEYED DIFF
7160-0902-05 DOCK-PANASONIC-FZA2 THICK DUAL RF KEYED DIFF

Certifications:

EN 55032: 2012/AC: 2013 Class A

•
EN 50498:2010

•
EN 50581:2012

•

Gamber-Johnson LLC, 3001 Borham Ave.,
Stevens Point, WI, 54481, USA, 715-344-3482

5 / 5