Page 1
INSTALLATION INSTRUCTIONS
Product
7160-0840
DELL 12" TABLET DOCKING STATION
Revision
Rev. A
Form
INST-748
Printing Spec:
PS-001
This instruction sheet is for the Dell 12" Tablet docking station only. For instructions
on features, set-up, and operation of the computer, please refer to the manual
provided by Dell with the computer.
This docking station is designed to be used with a variety of Gamber-Johnson
mounting systems. Installation instructions for other Gamber-Johnson products
are provided with each individual product.
This instruction sheet is for the following products:
Item No. 7160-0840-00
Item No. 7160-0840-02
No RF (External Power Supply sold separately)
Dual RF (External Power Supply sold separately)
Dell recommends using a Lind Auto Adapter to power the docking station. It can
be ordered from Gamber-Johnson (Item No. 16710 for vehicles)(Item No. 16793,
16794, 16795 for fork lifts). The vehicle power supply may be included with GJ Kits.
Product Mounting Disclaimer
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868
1 / 5
Page 2
PRE-INSTALLATION RECOMMENDATIONS
Conduct a "Bench Test"
Gamber-Johnson strongly advises a "bench test" be conducted to verify all
electronic and software issues are resolved prior to installation:
Make sure the computer is operational by itself.
1.
Insert computer into the docking station and verify that the computer is
2.
operating in the dock.
Interconnect entire assembly and verify start-up of all components,
3.
including other equipment (printers, modems, scanners, etc.)
Gamber-Johnson recommends positioning of all mounts and equipment in the
vehicle prior to the actual install to verify that mounting locations are safe and
practical.
IMPORTANT SAFETY INFORMATION FOR INSTALLERS
Safety is dependent on the proper installation and servicing of this docking station. It is
important to read and follow all instructions before installing this product.
To properly install a Gamber-Johnson docking station you must have a good
understanding of automotive electrical procedures and systems, along with proficiency
in the installation and service of aftermarket vehicle equipment.
There are no adjustments required at any time of the electrical components within the
docking station.
During Installation:
DO NOT
DO NOT
When drilling into the vehicle, DO make sure that both sides of the surface are clear of
anything that could be damaged.
CAUTION:
connect this docking station to the vehicle battery until:
All other electrical connections are made
1.
Mounting of all components is complete
2.
Verification that no shorts exist in the entire system
3.
install equipment or route wires or cords in the deployment path of any air bag.
If wiring is shorted to the frame, high current conductors can cause
Opening the docking station will void the product warranty.
hazardous sparks resulting in electrical fires or flying molten metal.
After installation:
Test the docking station to ensure that it is working properly.
File these instructions in a safe place and refer to them when performing maintenance
or re-installing.
WARNING
: Failure to follow all safety precautions and instructions may result in property
damage, serious injury, or death.
2 / 5
Page 3
DELL 12" TABLET DOCK FEATURE IDENTIFICATION
Upper Side Walls
Provides docking guidance
and connector protection,
prevents mis-docking
Lower Side Walls
AUX/Microphone
USB 2.0
Dual RF Connector
(Optional)
Docking Connector
Barrel Key Lock
Un-Latch Button
(User Interface)
Finger Print Scanner
Access
Guide Pins
Front Walls
Provides docking guidance
and connector protection,
prevents mis-docking
Dock "Latched" Position
Cable Tie Slots
(Port Specific)
Port Identification Label
Warranty Label
Part#/Serial# Label
Ethernet (RJ45)
(2) USB 3.0
Slam Latches
Cable Tie Slots
(External, Centered)
Cable Tie Slots
(External, Both sides)
RF - WWAN
RF - WLAN
Display
VGA
Serial (RS232)
Power Input: 19.5 Vdc
VESA 75mm Hole Pattern
1/4-20 unc Threaded Studs
3 / 5
Page 4
DOCKING AND UNDOCKING THE COMPUTER
TO DOCK THE COMPUTER
1. Insert the bottom of the tablet into the bottom cavity of the dock. The walls on the dock
will guide the tablet into place as the top of the tablet is angled outside of the dock.
2. Rotate the top of the tablet into the dock, overcoming the resistance until the Latch Button
returns to the "Latched" position. The grooves on the button line up with the lower groove on
the dock. There will also be an audible confirmation as the latch system springs downward.
3. With the dock in the "Latched" position, turn the lock to the "LOCKED" position (Clockwise).
Dock "Latched"
TO UNDOCK THE COMPUTER
1. Turn the lock to the "UNLOCKED" position (Counter Clockwise).
2. With your hand on the top of the tablet, use the thumb to push up on the blue button until
the dock is in the "Un-Latched" position and pull the top of the tablet forward. The grooves on
the button now line up with the upper groove on the dock (or higher).
3. After the tablet clears the latching system, remove the tablet by pulling it away from the
dock.
Dock "Un-Latched"
4 / 5
Page 5
Regulatory Certification Information
Regulatory Model #: 7160-0840
GJ Model #'s & Description:
7160-0840-00 Dock-Dell-12" Tablet-No RF
7160-0840-02 Dock-Dell-12" Tablet-Dual RF
Certifications:
EN 55032: 2012/AC: 2013 Class A
•
EN 50498:2010
•
EN 50581:2012
•
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions. (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Gamber-Johnson LLC, 3001 Borham Ave.,
Stevens Point, WI, 54481, USA, 715-344-3482
5 / 5
Loading...