Gamber-Johnson 7160-0572 User Manual

INSTALLATION INSTRUCTIONS

Form Product Revision

7160-0572

BASE - CHEVY EQUINOX/GMC TERRAIN 2010+

Rev.B

Printing Spec:

Required tools:
7/16" drill bit and drill motor (optional)
3/8" Socket wrench
5/16" Socket wrench

•You must read and follow all of these installation instructions. Failure to follow the installation
instructions may result in serious bodily injury or death

•DO NOT install or use this assembly in the area in which the airbag on the vehicle may be
deployed. The installer and user of this assembly are responsible for installing and using this
assembly outside the area in which an airbag may be deployed. (See Product Mounting
Disclaimer Below)

•Keep these installation instructions with the product and readily available in the vehicle
for future reference of other users of the product.

•Additional copies of the installation instruction can be obtained from Gamber-Johnson.
If you need assistance or have any questions, go to www.gamberjohnson.com or
call Gamber-Johnson at 1-800-456-6868.

•DO NOT remove the warning label form product under any circumstances.

INST-650

PS-001

Product Mounting Disclaimer

Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage

Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson

of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is

products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications

required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.

and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.

© Copyright 2013 Gamber-Johnson, LLC

If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868

Install Vehicle Base:

Move passenger seat to furthest back position. 1.
Pop out the trip clip that is on the front part of the trip, located on the outside passenger 2.

seat rail. Move trim out of the way slightly.

Recommended, drill second hole on inboard seat rail due to weight of the equipment on 3.
that rail. Drill a 7/16" hole located 1-1/8" back from the front hole of the inside seat rail on
the passenger seat. Ensure that this hole is alligned with the front hole. (Figure 1 shows side
of rail to drill into)

Slide base under the seat rails and allign the four holes with the PEMs of the base.4.

Insert and tighten a total of two 3/8" bolts and washers in the rear most holes of the base 5.
and seat rail

Insert and tighten a total of two 5/16" bolts and washers in the front most holes of the 6.
base and seat rail.

Push trim back in place that was moved in step 2. Pop trip clip back in as well.7.

Step 3

Figure 1

•This assembly should not be positioned in the area where the airbag may be deployed.

•DO NOT position the equipment in front of an airbag. Equipment positioned in front of an
airbag may cause serious injury or death if an airbag is activated.

•If installation of the equipment requires that the equipment be placed in front of an airbag,
the airbag should be deactivated. In order to secure permission for deactivating the airbag
you must contact the National Highway Traffic Safety Administration at 1-800-424-9393 to
gain permission to do so. If you have any questions or need assistance, call Gamber-Johnson
at 1-800-456-6868.

•High speed vehicle turns may cause parts of the assembly to swivel, interfering with the
driver or other equipment.