INSTALLATION INSTRUCTIONS
Product
Chevroley Caprice Console 2014+
Rev. A
Form Revision
INST-618
7160-0521-00, 7160-0521-01
Printing Spec:
This instruction sheet is for the following products:
Item No. 7160-0521-00 2014 Chevy Caprice Console only
Item No. 7160-0521-01 2014 Chevy Caprice Console with Cupholder and Armrest
Figure 1
Top Plate
Armrest
PS-001
Top Plate
mounting bolts
Front Mounting
Brackets
Parking Brake Cover
bolts
Parking Brake Cover
Cupholder
Rear Mounting Bolts
with Spacers attach
at this location
Product Mounting Disclaimer
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
© Copyright 2012 Gamber-Johnson, LLC
If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868
Vehicle disassembly:
1. Revmove the OEM Top Plate
by removing the 4 bolts using a
5/32" Allen wrench.
2. Remove the rectangular black
plate and spacers that cover the
parking brake mechanism.
Figure 2
3. Remove the 2 rear mounting
point bolts with a 10mm socket
from the vehicle center plastic
cover.
Figure 3
Figure 4
Console Installation:
4. Loosen the 4 screws that hold
the parking brake cover plate
inside the console box with an
1/8" Allen wrench. Remove the
top plate from the console box
using a 5/32" Allen wrench. See
Figure 1.
5. Place the console into position
between the seats. See Figure 5.
(Gamber Johnson does not have a
picture with the top plate removed
for installaion)
Figure 5
6. Attach the front legs to the
vehicle mount with the 1/4-20 x
3/4" bolts and flat washers
included in the hardware bag.
See Figure 6.
7. Attach the rear of the console
box to the location that you
removed the 2 bolts from earlier.
Use the M6 x 45mm bolts, Spacers,
and flat washers found in the
hardware bag. See Figure 7.
8. Attach the Top Plate to the
console box with the 1/4-20
screws removed earlier. See
Figures 1 & 8.
Figure 6
Figure 7
9. Tighten the #10-32 screws that
hold the parking brake cover in
place. See Figures 1 & 8.
Figure 8
Loading...