Gamber-Johnson 7160-0515-xx User Manual

INSTALLATION INSTRUCTIONS

Product

7160-0515

GETAC V110 DOCKING STATION

Revision

Rev.D

Printing Spec:

Form

INST-625

PS-001

This instruction sheet is for the V110 docking station only. For instructions on
features, set-up, and operation of the V110 computer, please refer to the manual
provided by Getac with the computer.

This docking station is designed to be used with a variety of Gamber-Johnson
mounting systems. Installation instructions for other Gamber-Johnson products
are provided with each individual product.

This instruction sheet is for the following products:

Item No. 7160-0515-00 Dock - Getac - V110 - No RF
Item No. 7160-0515-03 Dock - Getac - V110 - Tri-RF

Product Mounting Disclaimer

Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage

Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installa tion or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson

of any nature arising directly or indirectly as a result of the improper installa tion or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the loc ation of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is

products full consideration of vehicle occupants, vehicle systems (i.e., the loc ation of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications

required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.

and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.

© Copyright 2014 Gamber-Johnson, LLC

If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868

1/5

PRE-INSTALLATION RECOMMENDATIONS

Conduct a "Bench Test"
Gamber-Johnson strongly advises a "bench test" be conducted to verify all

electronic and software issues are resolved prior to installation:

Make sure the computer is operational by itself.1.
Insert computer into the docking station and verify that the computer is 2.
operating in the dock.
Interconnect entire assembly and verify start-up of all components, 3.
including other equipment (printers, modems, scanners, etc.)

Gamber-Johnson recommends positioning of all mounts and equipment in the
vehicle prior to the actual install to verify that mounting locations are safe and
practical.

IMPORTANT SAFETY INFORMATION FOR INSTALLERS

Safety is dependent on the proper installation and servicing of this docking station. It is
important to read and follow all instructions before installing this product.

To properly install a Gamber-Johnson docking station you must have a good
understanding of automotive electrical procedures and systems, along with proficiency
in the installation and service of aftermarket vehicle equipment.

There are no adjustments required at any time of the electrical components within the
docking station. Opening the docking station will void the product warranty.

During Installation:
DO NOT connect this docking station to the vehicle battery until:

All other electrical connections are made1.
Mounting of all components is complete2.

Verification that no shorts exist in the entire system3.
DO NOT install equipment or route wiring or cords in the deployment path of any air bag.
When drilling into the vehicle, DO make sure that both sides of the surface are clear of

anything that could be damaged.

CAUTION: If wiring is shorted to the frame, high current conductors can cause hazardous
sparks resulting in electrical fires or flying molten metal.

After installation:
Test the docking station to ensure that it is working properly.
File these instructions in a safe place and refer to them when performing maintenance or re-

installing.

WARNING: Failure to follow all safety precautions and instructions may result in property
damage, serious injury, or death.

2/5

V110 DOCKING STATION FEATURE IDENTIFICATON

Tri-RF Connector

Rear Hooks

Docking Connector

Front Hooks

Stylus Holder

Latch

Lock Button

Screen Support

Guide Blocks

Bumpers

Deck

4X 1/4-20unc x .62"
mounting studs

WWAN

WLAN

GPS

(2) Serial ports

Microphone

Headphone

VGA Port

2X 6-32unc inserts­Screen Support
mounting position

(3) USB 2.0 ports

Network (RJ-45)

19VDC Input port

(1) USB 3.0 port

HDMI Port

Strain Relief Bracket

3/5

DOCKING AND UNDOCKING THE COMPUTER

DOCKING THE COMPUTER

1. Turn the computer off.

2. Un-latch the dock, making sure the
rear hooks move backward (Figure 1).

3. With the computer held at an
angle, place the two notches on the
front edge of the computer into the
front hooks. (Figure 2)

4. Lower the computer down on to
the dock.

5. While pushing the computer down,
to compress the docking connector,
close the latch to engage the rear
hooks into the notches on the back
edge of the computer. (Figure 3)

Figure 1

Figure 2

6. Lock the latch, if required, for
security.

7. Adjust the position of the screen
support. (Figure 4)

UNDOCKING THE COMPUTER

1. Turn the computer off. Move screen
support back, close display.

2. Unlock latch, if locked.

3. Press the Lock Button on the latch.
The latch will spring open and the rear
hooks will disengage from the computer
case.

Figure 3

Figure 4

4. Lift computer up off dock, back
edge first.

4/5

Regulatory Certification Information

Regulatory Model #: 7160-0515

GJ Model #'s & Description:
7160-0515-00 Dock - Getac - V110 - No RF
7160-0515-03 Dock - Getac - V110 - Tri-RF

Certifications:

EN 55022:2010 CISPR 22:2008 Class B•
EN 50498:2010•
EN 50581:2012•
E-Mark•

-•

-•

-•

-•

This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions. (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interfernece that may cause undesired operation.

E

8

Gamber-Johnson LLC, 3001 Borham Ave.,
Stevens Point, WI, 54481, USA, 715-344-3482

10R-04 7267

5/5