INSTALLATION INSTRUCTIONS
Product Revision
7160-0512
Rev.A
Form
INST-612
G1 Riveted Keyboard Mount
Printing Spec:
This instruction sheet is for the FZ-G1 keyboard mount only. This mount is designed
to be used with Gamber-Johnson G1 docking stations, a Pansonic keyboard, or
I-Key keyboard. Installation instructions for other Gamber-Johnson products are
provided with each individual product.
Attaching the keyboard to the
keyboard bracket
1. Insert the 1/4-20 x 2" long hex bolt
1/4" acorn nut
through the mounting hole on the
keyboard bracket. The mounting hole
knob
has a hex shaped counterbore for the
head of the bolt to sit into.
2. Attach the bracket to the Keyboard
1/4" flat washer
steel washer
with the pan head screws provided in
the hardware bag. The I-Key keyboard
nylon washer
will use the (4) #8-32 x 1/4" long screws.
The Panasonic keyboard will use the (8)
M3 x 6mm long screws.
mounting
hardware
PS-001
3. Next attach the washers and hand
knob in the order shown to the right.
keyboard
bracket
4. Last Attach the Acorn nut to the
end of the bolt to keep the washers
1/4 x 2" hex bolt
and handle from falling off the bolt
when the handle is loosened to
remove the keyboard.
Product Mounting Disclaimer
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
© Copyright 2013 Gamber-Johnson, LLC
If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868
I-Key keyboard
Attaching the G1 dock to the Keyboard Mount
1. Attach the G1 dock to the Keyboard mount as shown below with the hardware
supplied with the docking station. A Gamber-Johnson clevis could also be attached to
the back side of the keyboard mount at this same location.
Mounting the Keyboard Mount in a vehicle
The keyboard mount has 1/4-20 threaded inserts on the bottom side for mounting to
Gamber-Johnson motion attachments. Attach with the 1/4-20 x 1/2" long socket button
head screws found in the hardware bag.
The mount also has a clearance hole for a 3/8" bolt and (3) .281 square holes that will
align with the smiley face pattern on Gamber-Johnson upper poles. Hardware has not
been included for these optional mounting locations.
hole for 3/8" bolt
.281 square holes
1/4-20 threaded inserts
Loading...