Page 1
INSTALLATION INSTRUCTIONS
Product
Getac S400 Docking Station
Revision
Rev. A
Form
INST-613
7160-0505-00 & 7160-0505-00-P
7160-0505-02 & 7160-0505-02-P
Printing Spec:
This instruction sheet is for the following products:
1. 7160-0505-00 & 7160-0505-00-P -- Keyed Alike, No RF.
2. 7160-0505-02 & 7160-0505-02-P -- Keyed Alike, Dual RF.
Figure 1
*These instructions are for the docking station only. For instructions on features, set-up
and operation of the Getac S400 computer, please refer to the manuals provided
with the computer.
PS-001
**This docking station is designed to be used with a variety of Gamber-Johnson
mounting systems. Installation instructions for Gamber-Johnson products are provided
with each individual product.
IMPORTANT SAFETY INFORMATION for
INSTALLERS
Safety is dependent on the proper installation and servicing of this docking station. It
is important to read and follow all instructions before installing the product.
To properly install a Gamber-Johnson docking station you must have a good
understanding of automotive electrical procedures and systems, along with
proficiency in the installation and service of aftermarket vehicle equipment.
There are no adjustments required at anytime of the electrical components within
the docking station. Opening the power/port replication housing will void the
product warranty.
Product Mounting Disclaimer
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
© Copyright 2013 Gamber-Johnson, LLC
If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868
Page 1 of 5
Page 2
During Installation
DO NOT connect this docking station to the vehicle battery until:•
ALL other electrical connections are made.1.
Mounting of ALL components is complete.2.
VERIFICATION that no shorts exist in the entire system.3.
DO NOT install equipment or route wiring or cords in the deployment path of •
any air bag.
When drilling into the vehicle, DO make sure that both sides of the surface are •
clear of anything that could be damaged.
CAUTION: If wiring is shorted to the frame, high current conductors can cause
hazardous sparks resulting in electrical fires or flying molten metal.
After Installation
Test the docking station to ensure that it is working properly.•
File these instructions in a safe place and refer to them when preforming
maintenance or re-installing.
WARNING: Failure to follow all safety precautions and instructions may result in
property damage, serious injury or death.
PRE-INSTALLATION RECOMMENDATIONS
Conduct a "Bench Test"
Gamber-Johnson strongly advises a "bench test" be conducted to verify that all
electronic and software issues are resolved prior to installation:
Make sure computer is operational by itself.1.
Insert computer into docking station and verify that the computer is operating in 2.
the dock.
Interconnect entire assembly and verify start-up of all components, including 3.
other equipment (printer, modems, scanners, etc.)
* Gamber-Johnson also recommends positioning of all mounts and equipment in the
vehicle prior to the actual install to verify that the mounting locations are safe and
practical.
POWER SUPPLY INFORMATION
This docking station uses an external power supply sold separately. Gamber-Johnson
recommends automobile power supply part number 15110. This power supply can
receive 12-32Vdc/15A max for input power and provides 19Vdc/5A of output power.
Along with the power supply comes cables to be used for connecting the output to the
dock and another cable to be used for plugging into a cigarette lighter for easy
connections.
Page 2 of 5
Page 3
Inserting the computer into Docking Station
Make sure the Sliding Door (located on 1.
the underside of the computer) has
been opened, exposing the computer's
docking connector. (see Figure 2)
Sliding Door
Make sure that the docking station Latch 2.
is in the open positon before inserting
computer. With the computer held at an
angle insert the front edge of the handle
under the front tabs. (see Figure 3).
Figure 2
Finish by setting the back of the 3.
computer onto the dock so that it is flat.
Press the latch until it is fully engaged
and remains closed. (see Figure 4)
To remove computer make sure 4.
computer is turned off and reverse
procedure above.
Latch
Figure 3
Figure 4
Page 3 of 5
Page 4
PORT IDENTIFICATION
DC In
Display Port
DVI Port
Serial Ports
2 USB/Ethernet Ports
PS2 Keyboard Port
e-SATA Port
WWAN
WLAN
Video Port
USB
Printer Port
PS2 Mouse PortFigure 5
Figure 6
Audio Out
Mic
Page 4 of 5
Page 5
Attaching Screen Support To Docking Station
The Screen Support provided with the docking station can be
attached to the right or left side. Use the #8-32 x .38 long screws to
attached the screen support to the docking station.
#8-32 x .38 Screws
(Provided)
Figure 7
Regulatory Certification Information
Regulatory Model #: 7160-0505
GJ Model #'s: 7160-0505-00, 7160-0505-00-P
7160-0505-02, 7160-0505-02-P
Descriptions: Dock-Getac-S400
1. 7160-0505-00 No/RF
2. 7160-0505-02 Dual/RF
3. 7160-0505-00-P No/RF
4. 7160-0505-02-P Dual/RF
Certifications:
*EN55022: 2010/AC:2010 Class A
*EN 50581:2012
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions. (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interfernece that may cause undesired operation.
Gamber-Johnson LLC, 3001 Borham Ave,
Stevens Point, WI, 54481, USA, 715-344-3482
Page 5 of 5
Loading...