Gamber-Johnson 7160-0431 User Manual

INSTALLATION INSTRUCTIONS

Product

7160-0409 THRU 7160-0412

FORD NGPI CONSOLE SEDAN & UTILITY, 2012+

7120-0579 Cable Kit
7160-0431 Filler Panel Assembly

Center Brace

USB/Audio
RELOCATION

Top Plate

Center Brace

Revision

Rev.B

Printing Spec:

Form

INST-568

PS-001

Top Plate

12v Knockouts

7160-0409 Shown

Armrest and Cupholder are

not included with 7160-0410

12v Knockouts

7160-0411 Shown

Armrest and Cupholder are

not included with 7160-0412

Product Mounting Disclaimer

Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage

Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson

of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is

products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications

required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.

and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.

If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868

1/3

Sedan:

1. Remove the stock tunnel plate by removing the 6 bolts.

2. The harness on the right side of the YAW sensor (located on the transmission tunnel) may
impede box installation. For ease of installation, pull up on harness to disconnect the push
fastener attaching the harness to the transmission tunnel.

3. The rear mounting points may be hidden under the flooring. Carefully cut the flooring as
shown to expose the mounting points (Fig 1).

Fig 1 - Rear Mounting Bracket, Carpet Cut to Revel Threaded Inserts

4. Slide console box into place.

5. Attach console to transmission tunnel using OEM hardware.

Utility:

1. Remove the lower dash trim panels on either side of the dash (Fig 2).

2. Remove the stock tunnel plate by removing the 6 bolts.

3. Remove the USB/Audio/12v jack Trim Panel (Fig 2) and disconnect the USB, Audio and 12v
cables.

4. The harness on the right side of the YAW sensor (located on the transmission tunnel) may
impede box installation. For ease of installation, pull up on harness to disconnect the push
fastener attaching the harness to the transmission tunnel.

5. Remove the Top Plate from the console box.

6. Slide the console box into place.

7. Attach the console to the transmission tunnel using
the OEM hardware.

8. Attach the Lower Dash Trim Panel to the console box
by placing the lower lip of the Trim Panel into the hook
on the bottom of the console box (Fig 3).

9. Attach the top of the Lower Dash Trim Panel to the
console box using the supplied Trim Hooks (Fig 3). Note
that the left Trim Hook has an "L" cut out of it. It may
be easier to remove the Top Plate when installing the
Lower Dash Trim Panels.

10. Snap the Lower Dash Panels back into place.

Fig 2 - Utility Lower Dash

Lower Dash
Trim Panel

USB/Audio
Trim Panel

2/3