Gamber-Johnson 7160-0418 User Manual

INSTALLATION INSTRUCTIONS

Product Revision Form

7160-0418 - YA LE ROLL FORMED PILLAR ASSY.

Rev.A

Printing Spec: PS-001

The following instruction sheet is for the mounting the Yale roll formed
pillar bracket assembly to a pillar of a fork truck.

Mounting the assembly to the pillar: See figure 1.
The bracket assembly is designed to at tach to the roll formed pillar on the

fork truck. The mo unts are held in place with 3/8" dia. hex bolts and
carriage bolts.

1. Attach the clam shell or ex tens ion tube assembly (sold separately) to
adapter bracket 1 with the 5/16" flat washers, lock washers, and he x nuts.

2. Clamp the adapter plates to the roll formed pillar with the 3/8

INST-567

hardware provided in the hardware bag. The 6" carrage bolts are for
larger roll fo rmed pillars. They will probably need to be cut down
depending on customer p r eference.

Figure 1

3/8" flat washers,
lock washers, &
hex nuts

Adapter Plate 2

3/8" lock washers, &
1 1/4" hex bolts

5/16" flat washers,
lock washers, &
hex nuts

Roll Formed Pillar

Adapter Plate 1

3/8" carrage bolts

Product Mounting Disclaimer

Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage

Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson

of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is

products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications

required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.

and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.

© copyright 2011 Gamber-Johnson, LLC

If y ou need assistance or have questions, call Gambe r-Johnson at 1-800-456-6868

Figure 1. - Example of Dual Clam Shell Assembly
attached to Yale Roll Formed Pillar Bracket Assembly

7160-0418 = Yale Roll Formed Pillar Bracket Assy.
7160-0366 = Fork Lift Dual Clam Shell W/Small Plate

Position so this surface
is relatively level

Position the 3/8 bolts as close to
the pillar as possible to prevent
bowing the components

Note: 1/4" bolts and flat washers have been provided
in the hardware bag and can be installed in the open
location opposite the lever handles to lock the clam
shells in place.

Note: The 3/8" pivot bolt
can be tightened to lock
the mount in place.

Figure 2. - Example of Extension Tube,
Clam Shell with 0-90 Clevis and 3" Arm

7160-0418 = Yale Roll Formed Pillar Bracket Assy.
7160-0363 = Extension tube
7160-0364 = Fork lift 0-90 Clevis W/Small Plate
CF19 Docking Station

Note: The 3/8" pivot bolt
can be tightened to lock
the mount in place.

Note: 1/4" bolts and flat washers have been provided
in the hardware bag and can be installed in the open
location opposite the lever handles to lock the clam
shells in place.

Position so this surface
is relatively level