Gamber-Johnson 7160-0415 User Manual

INSTALLATION INSTRUCTIONS

Product Revision Form

7160-0415 CF53 Cradle w/PushLock

Rev.A

7160-0415-01 CF53 C r a dle w/A u to L o c k
7160-0123 LED Light Asembly
7160-0124 Screen Support Assembly

Vehicle Mounting

The CF53 Cradle is designed to be used with Gambe r-Johnson motion attachments, poles and vehicle bases.
Four .25-20 x .50 long Button Head Screws are supplied in the cradle hardware bag to secure motion
attachments to the bottom side of the cradle.

Printing Spec: PS-001

Front Restraint

.25-20 x .50

Button Head Screws

PushLock
or
AutoLock

INST-564

Handle

Installing C F53 C o m p ute r int o Cradle

Press the PushLock or turn AutoLock with key, to move the Handle a nd Rear Hooks back.
With the computer tilted forward sl ightly, position the co mputer between the two side tabs and insert the
computer case handle under the Front Restraint.
Lower the back of the computer so al l four rubber feet are on the cr adle sur face and the back edge of
computer case is captured by the rear tabs.
Pull the cradle Hand le forward until the Rear Hooks engage the computer case and the Lock catches. Use
the supplied key to lock the PushLock if necessary.

Product Mounting Disclaimer

Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage

Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson

of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is

products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications

required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.

and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.

© copyright 2011 Gamber-Johnson, LLC

If y ou need assistance or have questions, call Gambe r-Johnson at 1-800-456-6868

Cradle A cc es so ries

7160-0124 Screen Support Assembly

Use two #8-32unc x .50 long Phillips Pan Head Screws
and two #8 Flat Washers to attach the Screen Support
Assembly to the bottom of the CF53 cradle as shown.
Positio n Screen S upport Ass e mbly forward or
backward to support Power Plug or allow access to
USB ports. Bend the Screen Support Arm slightly, if
needed, to contact the computer display.

7160-0123 LED Light Assembly

Use two #8-32unc x .50 long Phillips Pan Head Screws
and two #8 Flat Washers to attach the
Light Assembly to the bottom of the CF53 cradle.
If the Screen Support Accessory is also used place the
Light Assembly on the b ottom side as shown.

The LED is powered using the red and black wires on
the back of the light base. The LED Assembl y is
designed to operate on 12volts DC.

In a negative gr ound vehicle:
Connect the RED wire to the positive pole of the
vehicle battery or power distribution box. It is
recommended that a user-supplied fuse holder and 1
amp f us e be installed o n r e d wire. Co nn e ct the Blac k
wire to a suitable chassis GROUND or the
NEGATIVE pole of the battery.

Turn on LED by pressing the Activation
Button on head o f LE D Assembly .

Activation Button

Screen Support

#8-32 x .50 Screws
& #8 Flat Washers

#8-32 x .50 Screws
& #8 Flat Washers

LED Light Assembly

LED has three light options: White, Red and White/Red. Press the Activation Button to t oggle
throught options.

Hold the Activation Button down for approximately one second to turn LED off.