Gamber Johnson 7160-0410, 7170-0166, 7160-0412, 7170-0165, 7160-0409 Installation Instructions Manual

...

Download

Page 1

INSTALLATION INSTRUCTIONS

Product Revision

7160-0410, 7160-0412, 7170-0165, 7170-0166

FORD NGPI CONSOLE SEDAN & UTILITY, 2012+

Center Brace

NOTE: ARMREST AND CUP HOLDER SHOWN FOR REF. ONLY

USB/Audio RELOCATION

Top Plate

Rev.M

Top Plate

Form

INST-568

Printing Spec:

12v Knockouts

PS-001

Center Brace

Product Mounting Disclaimer

Product Mounting Disclaimer Gamber-John son is not liable under any theo ry of contra ct or tort law for any loss, da mage, personal injury, special, incidental or consequential damages for pe rsonal injury o r other damage

Gamber-John son is not liable under any theo ry of contra ct or tort law for any loss, da mage, personal injury, special, incidental or consequential damages for pe rsonal injury o r other damage of any nature arising directly or indirectly as a result of the improper installation or use of its products in ve hicle or any other application. I n order to safely install and u se Gamber-J ohnson

of any nature arising directly or indirectly as a result of the improper installation or use of its products in ve hicle or any other application. I n order to safely install and u se Gamber-J ohnson products full consideration of vehicle occupants, vehicle sy stems (i.e., the location of fuel lines, brakes lines, electrical, dr ive train or othe r systems), air-bags and other safety equipment is

products full consideration of vehicle occupants, vehicle sy stems (i.e., the location of fuel lines, brakes lines, electrical, dr ive train or othe r systems), air-bags and other safety equipment is required. Gamber-Johnson specifically dis claims any res ponsibility for the improper use or installation of its products not c onsistent with the original vehicle manufactures specifications

required. Gamber-Johnson specifically dis claims any res ponsibility for the improper use or installation of its products not c onsistent with the original vehicle manufactures specifications and recommen dations, Gamber-Johnson p roduct instruction sheets, or workmanship standards as endorsed through the Gambe r-Johnson Certified Installer Program.

and recommen dations, Gamber-Johnson p roduct instruction sheets, or workmanship standards as endorsed through the Gambe r-Johnson Certified Installer Program.

If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868

12v Knockouts

Note:

If there is no factory front console plate (Top Plate) installed, use hardware bag 7120-0630(included) for required hardware

Distributed By:

1/3

Page 2

Sedan:

1. Remove the stock tunnel plate by removing the 6 bolts.

2. The harness on the right side of the YAW sensor (located on the transmission tunnel) may impede box installation. For ease of installation, pull up on harness to disconnect the push fastener attaching the harness to the transmission tunnel.

3. The rear mounting points may be hidden under the flooring. Carefully cut the flooring as shown to expose the mounting points (Fig 1).

4. Slide console box into place.

5. Attach console to transmission tunnel using OEM hardware.

Utility:

1. Remove the lower dash trim panels on either side of the dash (Fig 2).

Fig 1 - Rear Mounting Bracket, Carpet Cut to Revel Threaded Inserts

2. Remove the stock tunnel plate by removing the 6 bolts.

3. Remove the USB/Audio/12v jack Trim Panel (Fig 2) and disconnect the USB, Audio and 12v cables.

4. Relocate OEM Module to under dash area (Fig. 3)

5. The harness on the right side of the YAW sensor (located on the transmission tunnel) may impede box insallation. For ease of installation, pull up on harness to disconnect the push fastener attaching the harness to the transmission tunnel.

6. Remove the Top Plate from the console box.

7. Slide the console box into place.

8. Attach the console to the transmission tunnel using the OEM hardware.

Fig. 3 - OEM Module located on backside of trim Panel

9. Attach the Lower Dash Trim Panel to the console box by placing the lower lip of the Trim Panel into the hook on the bottom of the console box (Fig 4).

Fig 2 - Utility Lower Dash

Lower Dash Trim Panel

USB/Audio Trim Panel

10. Attach the top of the Lower Dash Trim Panel to the console box using the supplied Trim Hooks (Fig 4). Note that the left Trim Hook has an "L" cut out of it. It may be easier to remove the Top Plate when installing the Lower Dash Trim Panels.

11. Snap the Lower Dash Panels back into place.

2/3

Page 3

Left Trim Hook

Lower Dash Trim Panel

Hooked into Console Box

Fig 4 - Installing Lower Dash

Trim Panels

Sedan and Utility:

Install the armrest (7160-0409 & 7160-0411) into the tube and adjust to the desired height/orientation then tighten the bolt under the armrest. Note: Armrest is not included with 7160-0410 or 7160-0412 but can be ordered separetly. The armrest mounting bracket can be flipped over to lower the armrest if desired or if used with a Printer Armrest.

The cup holder (MCS-INTCUP) can be placed anywhere along the horizontal length of the box. Note: The cup holder is not included with 7160-0410 or 7160-0412 but can be ordered separetly.

The Top Plate and Center Brace on both console boxes are designed to be removable to aid in installation and cable routing. If either item is removed Gamber-Johnson recommends reinstalling the screws with a drop of Blue 242 Loctite to prevent loosening. Torque the (4) top plate bolts to 65-80 in-lbs when reinstalling.

Both boxes have knockouts for 12v accessory outlets (7160-0063). To install simply punch out the desired knockout and install the 12v outlet. The 12v outlet will need to be hardwired into the vehicles power system. An additional 12v accessory outlet can be purchased for the second knockout if desired.

3/3