Gamber-Johnson 7160-0403 User Manual

INSTALLATION INSTRUCTIONS

Product Revision Form

7160-0403

Flat Floor Semi-Truck Base

Rev. A

Printing Spec: PS-001

The 7160-0403 Flat Floor Semi-Truck Base (Fig 1), is a no-drill solution that allows
a user to mount workstations, storage or console boxes.

The following instructions describe the installation of the base into an International
4300/7300 truck. The Base can also be installed in other similar sized trunks
although drilling of addition mounting holes maybe required.

The base and spacer plates mount under both driver and passenger seats.
Three locations of strut channel mounting, allows various positioning of equipment.

A 9/16" Socket & Ratchet or Wrench are needed for installation.

Fig. 1

INST-556

Mounting the Base and Spacer Plates (Fig. 2)

1. Remove and set aside fasteners securing passenger seat to floor of truck.

2. Tip passenger seat toward outside of truck, install base plate between floor and seat base.
Place base plate over two seat mounting studs, with the step portion toward center of
truck. Lower seat on to base plate.

3. Tip passenger seat toward center of truck, install spacer plate between floor and seat base.
Place spacer plate over two seat mounting studs. Lower seat on to spacer plate.

4. Install base and spacer plates under driver seat by repeating steps 1-4 on driver side seat.

5. Reinstall fasteners securing seats to floor.

Product Mounting Disclaimer

Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage

Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson

of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is

products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications

required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.

and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.

© copyright 2011 Gamber -Johnson, LLC

If y ou need assistance or have questions, call Gambe r-Johnson at 1-800-456-6868

1 of 2

.38-16 BOLTS AND WASHERS

CHANNEL NUTS

STRUT CHANNELS

SPACER PLATE UNDER

PASSENGER SEAT

BASE PLATE UNDER

PASSENGER SEAT

Fig. 2

Mounting the Workstation, Storage or Console Box (Fig. 2 & Fig. 3)

1. Determine location of equipment between driver and passenger seats.
Bolt strut channels to base plates accordingly, using (4) .38-16 bolts and washers,
supplied in hardware bag. Position strut channels to line-up with mounting holes
in equipment.

.38-16 BOLTS
AND WASHERS

BASE PLATE UNDER
DRIVER SEAT

FRONT OF VEHICLE

SPACER PLATE UNDER
DRIVER SEAT

2. Place (4) .38-16 channel nuts, supplied in hardware bag, in strut channel and
bolt equipment in place using (4) .38-16 bolts and washers.

Fig 3

2 of 2