Gamber-Johnson 7160-0380 User Manual

INSTALLATION INSTRUCTIONS

Product Revision Form

7160-0380

A

INST-546

Chevorlet Caprice Trunk Shelf, 2011+

TOP CROSS BAR

CABLE RETRAINT

HOLES

ORIENTATION TRIANGLE

POINT TO FRONT OF CAR

BACKER PLATE

Printing Spec: PS-001

SIDE BRACKET

SHELF ASSEMBLY

OPTIONAL ACCESSORY:

7160-0386

SHELF RAILING

Vehicle Disassembly:

1. Replace child seat anchor bolts with 2-1/4" bolts provided in hardware bag. Reuse stock
lock washer, spacer and child seat anchor (Fig. 1).

2. Remove rear seat cushions
a. Pull up on front of bottom seat cushion to release from clips
b. Remove bottom seat cushion
c. Remove four (4) 1/2" nuts ret aining b ack rest cushion
d. Lift back se at cushion to release fro m clips
e. Remove back seat cushion.

Product Mounting Disclaimer

Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage

Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson

of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is

products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications

required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.

and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.

© copyright 2011 Gamber-Johnson, LLC

If y ou need assistance or have questions, call Gambe r-Johnson at 1-800-456-6868

Factory Bolt

Not Used

Provided Bolt

with Factory Hardware

FIG. 1 - Replace Child Seat Anchors

Shelf Installation:

1. Using the supplied 1/4"-20 x.75" bolts, 1/4" lock washers and 1/4" flat washers, loosly assemble
the Side Bra ckets to the Shelf Assembly (Fig 5).

2. From inside the trunk, install the Top Cross Ba r using the supplied 5/16" washers and nylock
nuts. Note: The Top Cross Bar has a train gular cutout that should point to the front of the car.
Caution: Do not over tighten nuts as doing so may deform the Top Cross Bar.

3. Place shelf assembly in truck and hang on 1/4"-20 studs on ends of the Top Cr oss Bar (Fig. 2).

4. From inside ca bin, place Backer Plate into outer most obround depression and use as a te mplate
to mark and drill two (2) 5/16" diameter holes per side (Fig 3). Caution: Check for cables, wire
harness or other equipment before drilling in to the vehicle

5. Using supplied 1/4"-20 x .75" bolts, 1/4" lock washers and 1/4" washers, bolt through Backer
Plat e, rear seat w all and into threaded inserts on back of Shelf Assembly rails (Fig 4).

6. Tighten Side Bracket hardware (3 per side).

7. Reinstall rear seat.

FIG. 2 - Top Cross Bar Installation

FIG. 3 - Drill Backer Plate Mounting Holes

Driver Side Shown

Inside Trunk

Inside Cab

FIG. 4 - Backer Plate Hardware