Gamber-Johnson 7160-0201 User Manual
INSTALLATION INSTRUCTIONS
Product Revision Form
7160-0201
CRADLE, DELL E-64XX & E-64XX ATG
Rev. D
7160-0201 Cradle is designed to be used with a Dell E-Port or E-Port Plus Port Replicator.
The cradle is assembled for used with Dell E-6420 computer. By removing the 2 Side Spacers
the Cradle can also be used with Dell E-6400 & E-6410 computers (see page 2).
Tools Needed
#2 Philips Screwdriver
11/32" Box Wrench
5/32" Hex-Key Wrench
Mounting the Port Replicator
1. Place the Port Replicator on the cradle with front and side against locating tabs.
2. Loosen screws securing Left & Right Lower Brackets, turn Brackets over Port Replicator
and re-tighten mounting screws.
(The angle on brackets must match angle on Port Replicator or computer will not dock).
3. Attach Left & Right Rear Support Brackets using (4) #8 Flat Washers and (4) #8 Nylok Nuts.
4. Verify Left and Right Rear Support Brackets do not block any replicator ports.
5. Twist (4) Vinyl Caps onto the unused threaded studs.
Position replicator
using locating tabs.
INST-438
Right Lower
Bracket &
Mounting Screw
Figure 1
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program. The OEM port
replicators used in docking cradles are not warrantied by Gamber-Johnson.
© copyright 2011 Gamber-Johnson, LLC
Left Lower Bracket
& Mounting Screw
#8 Flat Washer
Vinyl Cap
#8 Nylon Lock Nut
If y ou need assistance or have questions, call Gambe r-Johnson at 1-800-456-6868
Page
1 / 5
Dell E-Port
Replicator
Right Rear
Support Bracket
Left Rear
Support
Bracket
INSTALLATION INSTRUCTIONS
Product Revision Form
7160-0201
CRADLE, DELL E-64XX & E-64XX ATG
Rev. D
Adjusting the Side Brackets
1. After the port Replicator has been installed, open the cradle by pushing the latch button
and pulling the sides outward.
2. Mount the computer onto the Port Replicator. A secure mount is confirmed with an audible
click of the Port Replicator.
3. If a E-6400 or E6410 computer is being used, take off both side hooks and remove the 3/8"
thick spacers. Reassemble the side hooks to the cradle.
4. Close the cradle, adjust the side hooks up or down to align with the computer case.
and secure the mounting screws with a 5/32" Hex-Key Wrench.
INST-438
Figure 2
Loosen and adjust side hook
with 5/32 hex-key wrench
Latch Button
Loosen and adjust side hook
with 5/32 hex-key wrench
Remove Side Spacers if using a
E-6400 or E-6410 computer
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program. The OEM port
replicators used in docking cradles are not warrantied by Gamber-Johnson.
© copyright 2011 Gamber-Johnson, LLC
If y ou need assistance or have questions, call Gambe r-Johnson at 1-800-456-6868
Remove Side Spacers if using a
E-6400 or E-6410 computer
Page
2 / 5
Loading...