Gamber-Johnson 7160-0082 User Manual

INSTALLATION INSTRUCTIONS

Product Revision Form #

Large Wo rk stat ion and Optio ns

7160-0082 - Large Workstation
7160-0083 - Computer Mounting Platform fo r Large Workstation
7160-0081 - Ve rtical Surface Mount
7160-0104 - Large Workstation w/Computer Mounting Platform
7160-0105 - Large Workstation w/Vertical Surface Mount

Rev. B

The Workstation provides lockable storage for supplies and equipment.
A removable Clipboard/Storage Pocket is mounted on the exterior and can be repositioned
to either side.
Removable brackets allow Letter size hanging folders to be supported inside the
Workstation. Hanging Folder Brackets can be repositioned inside the Workstation allowing
folders to hang front-to-back or side-to-side.
Wiring access cutouts allow electronic and charging devices to be installed inside the
locked Workstation.
Carrying cutouts on sides aid in moving and installing the Workstation.

The Workstation weights approximatly 60-70 lbs, use caution when moving and installing.

INST-359

The Workstation is typically installed between the driver and passenger seats with the
Clipboard/Storage Pocket toward the rear of the vehile.
This allows a computer mounting bracket (7160-0083 or 7160-0081) to be installed toward
the vehicle dash.

FIG. 1
7160-0082

Hanging Folder Brackets

Large Workstation

Clipboard/Storage Pocket
Mounted on End or Sides

Wiring Access

Cutouts

Carrying Cutouts

Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.

If y ou need assistance or have questions, call Gam be r-Johnson at 1-800-456- 6868

1 of 4

There are three ways to install and attach the Workstation to the vehicle floor.
Two require drilling holes into the vehicle floor, the third uses the existing seat bolts:

#1 - The box alone, without Adjustable Legs, can be attached to the vehicle floor.
Mounting holes are provided in the bottom of the Workstation (see Fig. 1).

#2 - The Workstation can also be attached to the vehicle floor using the Adjustable Legs
(see Fig 2).
Using the Adjustable Legs allows setting the Workstation at a convinent height or to
compensate for an uneven vehicle floor.

The Adjustable Legs allow 2.5" of vertical adjustment.
For shipping, the Adjustable Legs are wrapped and stored inside the box.
Attach the Legs to the Workstation with (4) .38-16 x .75 Hex Head Screws and (4) .38 Flat
Washers supplied in Hardware Bag 7120-0310.

Position the Workstation in vehicle.
Depending on vehicle used and desired location, a center console or seat section may
need to be removed.

Check that the location chosen does not interfere with the proper operation of or cause
damage to - wiring, fuel or hydraulic lines, the exhaust system or drive train components
and vehicle controls like gear shift lever, airbag sensors or airbag deployment zone.

Using the Workstation or Adjustable Legs as a template, mark the mounting hole
location on the vehicle floor.
Drill mounting holes thru vehicle floor.
Hardware Bag 7120-0310 includes .38 x 1.50 grade 5 bolts, .38 flat washers, .38 lock
washers, .38-16 hex nuts and .38-16 rivet nuts for bolting to the vehicle floor.
Depending on the vehicle application and tools available, the supplied hardware may be
used or the customer may supply equivalent hardware as needed.

#3 - If drilling into the vehicle floor is not possible, the Workstation may also be
attached to a Gamber-Johnson MCS Long or Short Top Plate & Vehicle Specific Leg kit
(see Fig. 3).

Check with Gamber-Johnson if a Vehicle Leg kit is available for your application.
Leg kits are typically installed by removing driver and passenger seat bolts, inserting
leg kit between seat bracket and vehicle floor, reinstalling the seat bolts.
Specific instructions are supplied with each leg kit.

The Workstation is bolted to the Top Plate using .25-20 x 1.00 Carriage Bolts, .25 Lock
Washers, .25 Hex Nuts.

2 of 4