Gamber-Johnson 7120-0635 User Manual

INSTALLATION INSTRUCTIONS

Product

7120-0587 & 7120-0635

NOTEPAD

TM

V & NOTEPAD

CAM CLIP CONVERSION KIT

TM

V-LT

Revision

Rev.C

Form

INST-577

Printing Spec:

PS-001

This kit contains the components needed to convert the Gamber Johnson Notepad V (7160-0250)
and Notepad V-LT (7160-0402) so that they can be used with smaller notebook and tablet format
computers, without the bulk of the Rear Support/Brace. The kit provides a depth adjustment of

7.2 - 8.1 inch when the Cam Mount Clip is installed facing inward and 8.1 - 9 inch when the Cam
Mount Clip is installed facing outward. The width adjustment, 10.62 - 16.50 inch (for Notepad V)
and 8.2 - 11.8 inch (for Notepad V-LT) remain unchanged. As does the height adjustment of 0 - 1.5 inch.

7120-0587

A 9/64 inch Hex (Allen) wrench will be needed for installation and adjustment.

7120-0587

A 9/64 inch Hex (Allen) with pin wrench / bit will be needed for installation and adjustment.

If attached, remove existing Rear Support/Braces from back edge of cradle. When finished cradle
should appear as shown in Fig. 1.

Fig. 1

Product Mounting Disclaimer

Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage

Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson

of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is

products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications

required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.

and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.

© Copyright 2012 Gamber-Johnson, LLC

If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868

1/4

ASSEMBLY
Install components of conversion kit as shown in Fig. 2. Position Cam Mount Clips facing inward

(shown) or outward based on depth adjustment range (see page 1) needed for computer/tablet.When
completed, cradle should appear as shown in Fig. 3. All screws should be loosely tightened to allow
side-to-side movement of Clip Guides and rotation of Cam Clips.

7120-0635

Use security hardware version of screws for the (3) #8 x .625 screws and (1) #8-32 screw. Sizes are still
the same as indicated

Cam Clip

#8 x .625 SHCS
Qty. 3

Qty. 2

5/16 External Tooth Lock
Washer, Qty. 2

Cam Mount Clip
Qty. 2

Clip Guide
Qty. 2

#8 Flat Washer
Qty. 4

Fig. 2

#8-32 x .625 SHCS

Spacer

#8-32 x 1 SHCS

Fig. 3

2/4