GAL A X Y AUDIO Quick Start Guide
Included Components
GALA XY AUDIO Quick Start Guide
1. GPS-8 x1
2. IEC Power Cable x1
3. Quick Start Guide x1
1.
2.
3.
Included Components
1. GPS-8 x1
2. IEC Power Cable x1
3. Quick Start Guide x1
Setup
1
Connect power cable to GPS-8, connect
other end to a power outlet.
3
Bring the GPS-8 down onto the speaker
stand gently until it is fit snugly.
4
To enhance the low frequencies, press
the Bass Boost button.
1.
2
From your mixer or source, connect an
XLR or 1/4" Cable into the Combo Jack
Input located on the back of the GPS-8.
4
Tighten the fastener by turning the knob
clock-wise until snug.
5
The green signal LED indicates you
have input signal.
The Red Limiter indicates too much
signal. If lit, turn the input down.
3.
2.
Stand Mounting (Optional)
1
3
Loosen the knob on the back of the
To loop to a second GPS-8, connect an
GPS-8 by turning counter-clockwise to
XLR female into the output and the male
ensure there is no obstruction in the
end of the cable to the input of the
mounting hole from the fastener.
second GPS-8.
Operation
1
2 3
For Line Level input, the button should
Insure the input level control is turned
be in the up position.
down (fully counter-clockwise) Turn the
For Mic Level input, press the button in,
power switch on.
the Mic On LED will light up.
The GPS-8 is a versatile speaker which can be mounted on a speaker stand as well as be
used as a wedge on stage.
2
Lift the GPS-8 over the speaker stand
and align it up with the hole.
Level control: turn clockwise to raise the
level. Turn counter-clockwise to lower
the level.
Setup
1
Connect power cable to GPS-8, connect
other end to a power outlet.
3
Bring the GPS-8 down onto the speaker
stand gently until it is fit snugly.
2
From your mixer or source, connect an
XLR or 1/4" Cable into the Combo Jack
Input located on the back of the GPS-8.
4
Tighten the fastener by turning the knob
clock-wise until snug.
3
To loop to a second GPS-8, connect an
XLR female into the output and the male
end of the cable to the input of the
second GPS-8.
Operation
1
For Line Level input, the button should
be in the up position.
For Mic Level input, press the button in,
the Mic On LED will light up.
Stand Mounting (Optional)
1
Loosen the knob on the back of the
GPS-8 by turning counter-clockwise to
ensure there is no obstruction in the
mounting hole from the fastener.
2 3
Insure the input level control is turned
down (fully counter-clockwise) Turn the
power switch on.
2
Lift the GPS-8 over the speaker stand
and align it up with the hole.
Level control: turn clockwise to raise the
level. Turn counter-clockwise to lower
the level.
4
To enhance the low frequencies, press
the Bass Boost button.
5
The green signal LED indicates you
have input signal.
The Red Limiter indicates too much
signal. If lit, turn the input down.
The GPS-8 is a versatile speaker which can be mounted on a speaker stand as well as be
used as a wedge on stage.
Quick Start Guide
FAQ
1. Q. Can the GPS-8 be used outside of the US?
A. Yes, but you must change the mains switch to the proper voltage for your location.
2. Q. Can I plug a microphone directly into the GPS-8?
A. Yes, but it must be a dynamic mic. There is no Phantom Power for condenser mics.
Other Helpful Sources
GPS-8
Product Page
GPS-8
Cutsheet
TM
GPS-8
Manual
(PDF Download)
GPS-8
How To Video
(PDF Download)
Specifications subject to change without notice.
601 E. Pawnee Wichita, KS 67211 316. 263.2852 FAX 316.263.0642 www.galaxyaudio.com
Distributed in Canada by Audio Distributors International (ADI) 1275 Newton, unit 6 Boucherville, QC J4B 5H2 Canada
450.449.8177 FAX 450.449.8180
Printed in China
V20151124