Galaxy Audio DHXR4 Quick Start Guide

GAL A X Y AUDIO Quick Start Guide
Included Components
1. DHXR4 x1
2. Antennas x2
3. Rack Ears x2
4. 1/4" to 1/4" Audio Cable x1
5. Power Supply x1
6. BNC Connectors x2
7. BNC Cables x2
8. Screws x6
9. Antenna Plugs x2
10. Quick Start Guide x1
1
Insert the 5.5mm plug into the DC input jack, plug the wall wart into a 120VAC outlet.
1.
2.
5.
6.
3.
7.
4.
8.
GALA XY AUDIO Quick Start Guide
10.
Included Components
1. DHXR4 x1
1.
2. Antennas x2
3. Rack Ears x2
4. 1/4" to 1/4" Audio Cable x1
5. Power Supply x1
6. BNC Connectors x2
7. BNC Cables x2
8. Screws x6
9. Antenna Plugs x2
10. Quick Start Guide x1
Setup
1
Insert the 5.5mm plug into the DC input jack, plug the wall wart into a 120VAC outlet.
Rack Mounting (Optional)
Attach the rack ears using the provided screws.
2
Press the "SET" button twice, the group number will flash, use the up and down buttons to select a group.
3.
2.
7.4.6.
5.
2 3 4 5
Individual Outputs: Connect a shielded microphone cable to each channel’s XLRM output, connect the other end into your mixer input.
Front Mount Antenna (Optional)
1
Attach the BNC feed-through connectors to the rack ears.
3
Press set again, the channel number will flash, use the up down buttons to select a channel.
10.
8.
9.
2
4
Combined Outputs: 1/4" Connect one end of a shielded 1/4"M to 1/4"M cable to the 1/4" Mix output, connect the other end into your system input.
Attach the short BNC cables to the rear panel antenna jacks, and to the BNC feed-through connectors on the back of the rack ears.
With the transmitter turned on, place the transmitter with it’s IR window (figure 4a) facing the receiver IR window (figure 4b), about 6" away. Press the ADS button on channel 1.
Optional Accessories
1. HH65SC Handheld Mic
2. HH65 Handheld Mic
3. MBP77 Body Pack
4. LV-U3BK Lav Mic
5. AS-GTR Guitar Cable
6. HS-U3BK Headset Mic
7. SM-W77 Shockmount Base
Combined Outputs XLR Connect one end of a shielded microphone cable to the mix XLRM output, connect the other end into your system input.
31
4a
4b
Optional Accessories
What May be Needed
1.
to Rack
(Not Included)
2.
1. Rack Screws 10/32 x .75",
Phillips Truss Head Screws
4.
3.
2. #2 Phillips Head
7.
5.
Screwdriver
6.
1. 2.
Attach the antennas to the antenna jacks
Operation
1 1
Power on the receiver
Follow steps 2, 3 and 4 of “Operation
5
for each channel. Use the same group, but a different channel for each. Ex: Group 1; Channels 1, 2, 3 and 4.
1. HH65SC Handheld Mic
2. HH65 Handheld Mic
3. MBP77 Body Pack
4. LV-U3BK Lav Mic
5. AS-GTR Guitar Cable
6. HS-U3BK Headset Mic
7. SM-W77 Shockmount Base
1.
3.
2.
4.
7.
5.
6.
9.
2 3 4 5
Individual Outputs: Connect a shielded microphone cable to each channel’s XLRM output needed, connect the other end into your mixer input.
Combined Outputs: 1/4" Connect one end of a shielded 1/4"M to 1/4"M cable to the 1/4" Mix output, connect the other end into your system input.
Combined Outputs XLR Connect one end of a shielded microphone cable to the mix XLRM output, connect the other end into your system input.
What May be Needed to Rack
(Not Included)
1. Rack Screws 10/32 x .75",
Phillips Truss Head Screws
2. #2 Phillips Head
Screwdriver
1. 2.
Attach the antennas to the antenna jacks
Rack Mounting (Optional)
Attach the rack ears using the provided screws.
2
Press the "SET" button twice, the group number will flash, use the up and down buttons to select a group.
Front Mount Antenna (Optional)
1
Attach the BNC feed-through connectors to the rack ears.
3
Press set again, the channel number will flash, use the up down buttons to select a channel.
2
Attach the short BNC cables to the rear panel antenna jacks, and to the BNC feed-through connectors on the back of the rack ears.
4
With the transmitter turned on, place the transmitter with it’s IR window (figure 4a) facing the receiver IR window (figure 4b), about 6" away. Press the ADS button on channel 1. This will sync the Transmitter to the Receiver.
31
Attach the Antenna to the front end of the BNC Connectors.
4a
4b
Operation
1
1
Power on the receiver
Follow steps 2, 3 and 4 of “Operation
5
for each channel. Use the same group, but a different channel for each. Ex: Group 1; Channels 1, 2, 3 and 4.
Quick Start Guide
FAQ
1. Q. I’m having problems finding the best frequency for me. Where do I go to find this information?
A. Please consult the online manual or visit: GalaxyAudio.com/Frequencies.php
2. Q. I’m using channels on the same group and having issues.
A. It is ok to use multiple groups if you cannot get all channels to work within one group.
3. Q. How do I use the Scan function?
A. Consult the online manual for detailed instructions at: GalaxyAudio.com/pdfs/DHX-Manual.pdf
Other Helpful Sources
DHXR4 Product Page
DHXR4 Cutsheet
TM
DHXR4 Manual
(PDF Download)
DHXR4 How To Video
(PDF Download)
Specifications subject to change without notice.
601 E. Pawnee Wichita, KS 67211 316. 263.2852 FAX 316.263.0642 www.galaxyaudio.com
Distributed in Canada by Audio Distributors International (ADI) 1275 Newton, unit 6 Boucherville, QC J4B 5H2 Canada
450.449.8177 FAX 450.449.8180
Printed in China
V20151021
Loading...