Galaxy 58715132400, 58715132401, 58715132402, 58715132403, 58715139400 Installation Guide

Dishwasher

Installation

Instructions

INSTALLER: Leave Installation Instructions with owner.
OWNER: Read your dishwasher Use and Care Guide. It contains

important safety information for operating this appliance. It also has
many suggestions for getting the best results from your dishwasher.

Printed in U.S.A. 154524101

(05/04)

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

Read all instructions before installing dishwasher.

For your safety, please read and observe all safety instructions.

This guide will help you anticipate drain, water, and electrical
connections, and help you select the best location for the dishwasher.

Tip Over Hazard

Do not use dishwasher until completely installed.

Do not push down on open door.
Failure to follow this warning can result in serious injury.

Parts You Will Need*

• Drain Hose Clamp, 1'/4"Diameter (included)

• Elbow, 90° with a %" National Pipe Thread (not included)

• Conduit Connector (not included)

• Wire Nuts, two (2) for 12-14 gauge wire (not included)

If required:

• "Y" Branch Tailpiece and
Connector Kit (See Step 4)

• Air Gap Kit (See Step 4)

• Fasteners for floor
anchoring (See Step 9)

Electric Shock Hazard

Disconnect electrical power at the fuse box or
circuit breaker box before beginning installation.
Failure to follow this warning could result in death

or serious injury.

• Examine dishwasher and locate connections. See Step 4.

• Locate dishwasher where there is easy access to drain, water,

and electrical lines. The best location is on either side of the
kitchen sink for access to existing plumbing and ease in

loading dishes. See Step 4.

• Electrical, water, and drain connections are not the same for

all age, brands, or models of dishwashers. Check the location
and length of home utilities. See Step 4.

• A 15-20 amp, grounded, 120 volt AC only, electrical supply is
required. See Steps 4 and 8.

• If dishwasher drain hose will be connected to a food disposer
for the first time, knock out plug located inside disposer inlet.

See Steps 4 and 6.

• Kinked water or drain hoses can cause problems. See Step 6.

• Dishwashers need to be connected to a hot water supply with

enough water pressure to insure an adequate fill. See Steps 4
and 7.

• Each home installation differs. You will need additional parts
listed above to complete your installation. See Steps 4 and 7.

• Flush water line prior to making the final connection to
prevent clogging of dishwasher's filter screen. See Step 7.

• The dishwasher will look, sound, and perform best when
properly leveled. See Step 5. (NOTE: If levelers are removed
during installation, make sure the floor is flat and free of any
obstruction.)

• Anchor the dishwasher to countertop. See Step 9.

1. Remove two (2) screws at front of the kickplate assembly

using a #2 Phillips screw driver.

2. Tilt and pull forward to remove. (Figure 1).
NOTE: It is not necessary to remove the outer door for installation.

However, you might find it more convenient to do so. You
can find directions for removing door in Step 10.

Available at:

Plumbing Supply Store

Plumbing Supply Store
Hardware Store

Electric Shock Hazard

Observe all local codes and ordinances for electrical

and plumbing connections. All electrical and

plumbing work should be performed by qualified
persons. Failure to follow this warning could result
in death or serious injury.

1. Make sure your location has the right drain, water, and electrical

outlets to make the connections. Do not install unit under a
cooktop range. Damage to plastic tub will occur.

©

I 90° "-,-4, / ©

Elect_cal, water,

and drain lines

24,,_

min.

must be con[ined to

shaded area.

©

_ 18"

@

Z

7J(2"/

\ \\

24" _ 1_/z"

Fi_I//'e 2

IMPORTANT: For proper operation and appearance of unit,
cabinet opening should have dimensions as shown in Figure 2.
If unit is to be placed in a corner, there must be at least a 2-inch

side clearance to open door.

2. Remove any carpet from area to provide motor clearance. Floor

should be flat and free of any obstruction.

IMPORTANT: Drain, water, and electrical lines should be
roughed-in before going any further.

Electric Shock Hazard

Electrical, water, and drain lines must be confined
to shaded areas in Figure 2.

Electric conductors, water, and drain could be
damaged.
Failure to follow these instructions could result in
fire or electric shock.

NOTE: If dishwasher is installed at end of a cabinet line, sides

and back must be fully enclosed.

IMPORTANT: Disconnect power before starting installation.

Electrical

1. The dishwasher operates on a 120 volt, 60 Hz electrical supply.
Provide a separate circuit with a fuse or circuit breaker rated for
at least 15 amps (20 amps if connected with disposer) but not
more than 20 amps.

2. Note the locations of electrical supply and dishwasher's electrical

junction box on right underside of unit behind kickplate assembly.

See Figure 3.

3. Cut access hole in shaded area shown in Figure 2.

4. Pull electrical cable through hole into installation area.

Water

1. Determine where you will connect to hot water supply. Review
Figure 3 and note the location of water inlet valve.

Property Damage

Do not use the furnished drain hose or a rubber garden hose

for the water supply line. Either of these hoses can burst.

Flooding may occur and cause property damage.

.

Be sure water inlet valve is protected from freezing. Ifvalve
freezes and ruptures, flooding may occur.

3.

Determine amount of tubing needed to connect hot water supply
to the unit's water inlet valve. Copper tubing must have a
minimum .%" OD. High-pressure and high-temperature rated
plastic tubing with a minimum inner diameter of W' may be

used. A shut-off valve installed outside dishwasher cabinet is
best. See Figure 4.

iii iiiililiiiiii!iiii!iiiiiii! i ii!i!i!iiiiii i!!iil¸

!!iii_iii!i_ii_;i¸iiii!ii!ii!i;!ii!_!i;_i_!i_!i_!i_!i_!i_!i_!i_!i_!_!i,liiiili!!ii!_!iiiii_il¸ii!ii!!_!!i_iiii!_!:!i;iiiiiiii!!!iiiill¸!i!!i¸iiil;i!;!i_
i!i_ili_iiiii_iill¸i_ii!iiiii!:i!i¸i¸iil;!ii!i¸i_i!i!i!iiiii¸_ii¸!_!!i

!i(!iiii!!i!i!II i!! ii!iii il

J_e4

4. Cut water access hole in shaded area in Figure 2.

5. Route water supply line into installation area.

IMPORTANT: Incoming hot water temperature should be at
least 120°F (49°C). Water pressure should be between
20-120 psi.

Drain

1. Review Figures 5 and 6 to see the different ways to connect
dishwasher to drain system. Choose method that best suits your

need.

3. If you connect to a sink trap, local codes may require you to
install an air gap kit, not included. The drain hose will be routed
from dishwasher to air gap inlet as shown in Figure 6. An air gap
kit is available from a plumbing supply store.

4. If you connect to a disposer, the large end of drain hose will fit.

Figure 7(a). The knock out plug must be removed from

inside disposer inlet before making the final fit to drain hose.

See Figure 7(b).

Drain

Motor Larger end

End fltsdisposer

Inlet fitting.

Drain Hose

l_gure 71a)

5. Before cutting drain hose access, check both sides of selected
area to avoid interference. Cut a 2" diameter hole in shaded area

shown in Figure 2.

6. If the cabinet wall is wood, sand edges of hole until smooth and

rounded. If cabinet wall is metal, cover all sharp edges with

electrical or duct tape to avoid cutting drain hose.

Cutfor 3/4" connection.

Tools and Materials Needed for

Installation

• Drill, Electric

• Driver, Socket V16",1/4",s/16"

• Flaring Tool / Tube Cutter (for copper tubing)

• Flashlight

• Gloves

• Level

• Pipe Joint Compound (for iron pipe plumbing) or
Pipe Thread Tape (for sealing threads)

• Pliers

• Safety Glasses

• Saw, Keyhole or 1/2",11/2"to 2" Hole Cutters

• Screw Drivers, Slotted and #2 Phillips (magnetic tip
preferred)

• Tape, Electrical or Duct

• Tape, Measuring

• Wire Stripper or Utility Knife

• Wrench, Hex-end

• Wrenches, 2 Adjustable (for copper tubing)
or 2 Pipe wrenches (for iron pipe plumbing)

/ Adjustable Toeplate

Kld_plate

%

Water Inlet

Valve _ Bottom Screws

Fi_Ure l

3. Locate water inlet valve behind kickplate on bottom left underside
of unit. The valve has a %" NPT female fitting.

4. Wrap 90° elbow (not included) with pipe thread tape (or apply
joint compound) and thread it into water inlet valve.

5. Tighten elbow with a wrench, leaving elbow pointing toward rear
of unit. To prevent bending of bracket or breaking of valve, avoid

overtightening.

IMPORTANT: Do not cross drain, water, and electrical lines in

front of dishwasher motor or frame.

Locating the Connections

1. Review dimensions in Figure 3 to locate dishwasher's drain,
water, and electrical connections.

2. All connections must be made in shaded area in Figure 2.

Left Side Front

24 J/J'

_ 23 7/s" ,

Irl.

, 49 _/4

/ I

Doorin =

openposliion i

BightSide

........ i

iL '

_ 173/J ' ÷

From rear to

juncllon box.

From _ to

_enter of water

inletvalve.

3_/," [

From floor to [

watcrinlet I

valve. [

Junction Box

(not visible)

Entry Must be

Above

I;

Sink at l._ft

l
l

I

.

If you connect to a sink drain, entry will need to be above trap.
A "Y" branch tailpiece and connector kit, not included, will make
this method easier and includes all needed fittings and
instructions. See Figure 5.

.

Measure height of cabinet opening
from underside of countertop to floor.
Check chart for height opening and
suggested adjustment.

Leg Leveler

Height of

Cabinet Opening

34" (86.4cm)

34W' (86.7cm)

34V1_"(87.2cm)

341/_" (87.6cm)

For additional height

.

Move dishwasher to front of installation area.

3.

Loosen the front and rear leveling legs by turning
counterclockwise. Refer to chart for number of turns. See

Figure 8. Front levelers should allow W' below underside of
countertop.

Adjustment Chart

Number of Turns to

Adjust Levelers

0
2

6
9

add shims under levelers.

Clamp

/

F_re I0

The drain hose loop must be at least 32" _ from the floor to
Insure proper drainage.

Property Damage

Do not solder within 6" of the water inlet valve. Damage to

the plastic parts in the valve may occur.

Use care that no sealer, dirt, or other objects enter the valve.
Damage to the filter screen may occur.

Be sure the dishwasher is placed where the water inlet valve

will be kept from freezing. If the valve freezes, it may rupture
and flooding may occur.

Electrical Supply

1. Remove junction box cover and pull house wiring into junction
box. See Figures 12 and 13.

2. Use a UL listed conduit connector, not included, at box to
stabilize wiring.

IMPORTANT: Be sure electrical cable is not routed behind

dishwasher s motor.

Through

Wall

Junction Box

(inplace)

l_ure 12

3. Inside junction box, attach ground wire under head of grounding
screw and tighten. See Figure 13.

4. Connect incoming black lead to dishwasher's black lead and
incoming white lead to dishwasher's white lead with wire nuts or
other suitable connectors, not included. Wire nuts should be tight.

5. Replace junction box cover. See Figure 13.

Note: If mounting your dishwasher to the counter top or to the floor is

not a disirable option, you can order the side mounting kit,

154477201, by calling 1-800-My-Home. This allows you to install the

dishwasher by securing it to the cabinets or partitions on either side of
the unit. The kit utilizes the front frame of the dishwasher to secure

the unit to the cabinet or partitions.

Disconnect electrical power at the fuse box or

circuit breaker box before beginning installation.

l_el Electric Shock Hazard

Failure to follow this warning could result in death
or serious injury.

.

When ready to replace door, fit the slots on each side of top door
edge over the tabs on the metal liner. Push on sides to insure the
door is flat. Push up from bottom until there is no gap between
door and control panel. See Figure 16c.

HgUre 16C

Control Panel

Side View

6. Unlatch door and open while supporting outer door on both sides
at bottom to keep in place. Align screw holes and replace screws.

Front Leveler

l_re 8

4. If levelers have to be removed, make sure floor is free of
obstructions.

5. Place dishwasher inside cabinet area so that it is centered in
opening. Use caution when moving dishwasher to prevent

damage to dishwasher, floor, and cabinets.

6. Check that dishwasher is level from side to side by placing a

level against the top front section of the tub. See Figure 9a.

J

Rear Leveler

_igure oa _igure 9b

7. Check that dishwasher is level from front to back by placing level

on side of opened door. See Figure 9b.

8. Adjust levelers up or down until dishwasher is level.

Helpful tip for built-up floors:

Measure height of opening from underside of countertop to built-up
floor. If the height is at least 33-3/4" (84.5 cm), the dishwasher will fit
into the opening without modification to the countertop or flooring.

Put front and rear levelers all the way up. If the opening is at 33-3/4"
(84.5 cm), the countertop mounting brackets may need to be removed
to avoid damage to the top of the dishwasher console. If so, follow
directions in Step 9 for floor anchoring when ready to secure unit.

Water Line

1. Flush water line before connecting it to water inlet valve to
prevent early clogging of filter screen. Place a bunched towel
over end of line to prevent splashing. Open valve for a few
seconds and let water drain into a pan. Turn off water supply

at shut-off valve.

l_gure II

2. Route water line to water inlet valve as shown in Figure 11.

3. While firmly pulling water supply line into 90° elbow, tightly
connect water supply to water inlet valve. Supply line must be
free of kinks, scales, chips, and lubricants.

4. Turn on water supply and check for leaks.

5. If water inlet valve clogs, make sure water supply is off. Remove
four (4) screws at inlet end of valve and clean filter screen.

Through
Wall

Conduit
Connector Ground Wire

Widte Wire to Junction
Widte Wire Box Cover

(Neutral)

Black Wire to
Black Wire (Hot)

Fioo_lre 13

The dishwasher must be secured to keep it from tilting when door is
opened. Choose one of the methods described belowto secure unit.

Countertop Anchoring

1. Adjust levelers (see Step 5) so mounting brackets touch
underside of countertop. IMPORTANT: Dishwasher must rest
on floor--do not hang from countertop. See Figure 14.

2. Screw mounting brackets firmly to countertop using screws
provided in literature packet.

3. Open and close dishwasher door slowly. If door hits mounting
bracket screw heads, adjust front levelers.

Note: Open and close door to make sure it does not hit

surrounding cabinets or countertop.

Cut Hazard

Metal color panels are sharp and should be
handled with care. Wear gloves to protect hands.

Failure to follow this warning may result in injury.

To Remove and Replace Outer Door

1. Unlatch and open door. Using a Phillips head screw driver,
remove two (2) lower screws from inner door. Save screws to

reassemble. See Figure 16a.

Figure 16a

.

Close and latch door while holding both sides.

3.

Place one hand on each side of door and pull down at top
approximately 1/4". Pull entire door assembly toward you to
remove. See Figure 16b.

k3/_urei eb

_.77 .= ... .77 .- -=:7=-- =- - . .. . ..7_77_-= TT ...=.

Before starting the dishwasher,
check these #ems:

Drain hose is assembled to drain pump.
All packing materials and consumer literature have been

removed from unit.
Dishwasher is level and securely fastened.

Open and close door to make sure it does not hit surrounding
cabinet or countertop.

Water and drain lines have no kinks.
Wiring connections to junction box are tight.

Water supply is turned on.
Joints are free of leaks.

Replacing Door

1. Refer to Step 10, numbers 5 and 6, for replacing outer door.

2. Adjust door springs to balance weight of door. A correct spring
setting allows door to remain horizontal in opened position, yet

will rise to close with slight lift fo finger.

3. If necessary, increase tension by moving springs to a hole toward

rear of unit or decrease by moving them toward front. See Figure

17.

4. Turn electrical supply on.

Electric Shock Hazard

Plumbing material and drain hose must not come in

contact with wiring or electrical components.

Failure to follow this warning could result in
personal injury from exposed wiring.

1. Pull out unit and check to see if drain hose is correctly attached to

the drain pump assembly. If drain hose is not attached to drain

pump, follow the instruction sheet (included with drain hose) on
how to correctly install the drain hose to the drain pump assembly.

2. Move unit back in place while routing drain hose through access
hole. Use caution to prevent damage to the dishwasher, floor and

cabinets. IMPORTANT: Make sure there are no sharp bends or

kinks that might restrict drain flow.

3. Secure drain hose to sink drain, disposer, or separate trap with a

clamp. IMPORTANT: Be careful not to overtighten clamp or you

may damage end of hose. Do not connect hose to horizontal pipe
between sink drain and disposer.

4. Be sure unit does not rest on drain hose. It should be free of
electrical components and door springs. Do not cut corrugated

drain hose. Pull excess through cabinet and place under sink.

Make sure hose does not come in contact with any sharp edges.

See Figure 10.

Electric Shock Hazard

Make sure electrical power has been disconnected at fuse box

or circuit breaker box.
The dishwasher must be connected to a grounded metal,

permanent wiring system. The equipment-grounding
conductor must be run with the circuit conductors and

connected to the appliance's equipment grounding terminal

or lead. It is the consumer's responsibility to contact a

qualified installer to make sure the electrical installation

conforms with the National Electrical Code and local codes
and ordinances.

Do not connect the dishwasher to the power supply until the

appliance is permanently grounded.
All wiring connections must be enclosed in the junction box.

This unit has copper lead wires.
Joining aluminum building wire to stranded copper wire

should be done by a qualified electrician using materials

recognized by UL and local codes.
Do not use an extension cord. Such use can result in fire,

electrical shock, or other personal injury.

Failure to follow these instructions could result in death or

serious injury.

_i! i_ iiiiii

_i_ iiiI i_ i

#Sx /8 (indudedinthe
litemturepacket).

Fl_e 14

Floor Anchoring

This procedure is difficult and should be used only if countertop
mounting brackets cannot be used.

1. Screw W' lag screws, not included, through holes provided in
frame rail. See Figure 15.

2. Use expansion fasteners if floor is concrete.

Operate the machine through at

?

least one fill and pump-out,
checking the following items:

L At first fill, make sure water completely covers filter surface.

(Motor pump sound may be heard before water enters unit).
At pump-out, make sure all water is pumped out.
Check water connections again for leaks.

Electric Shock Hazard

If all connections are correct, there are no leaks,
and unit runs properly, replace the kickplate
assembly before placing unit into operation.

Failure to follow this warning could result in
electric shock.

4. Place door where it willnot get scratched or damaged while

completing installation.