Pub. 42004-308G
GAI-TRONICS®
A HUBBELL COMPANY
Model 234WM-202
Wall-Mount Stanchion Assembly
Confidential ity Notice
This manual is provided solely as an installation, operation, and maintenance guide, which contains
sensitive business and technical information that is confidential and proprietary to GAI-Tronics. GAITronics retains all intellectual property and other rights in or to the information contained herein, and
such information may only be used in connection with the operation of your GAI-Tronics product or
system. This manual may not be disclosed in any form; in whole or in part, directly or indirectly, to any
third party.
General Information
The Model 234WM-202 Wall-Mount Stanchion Assembly is part of a completely integrated emergency
communications station and is designed to house a GAI-Tronics Model 39x or 27x Series Flush-Mount
Telephone and a Model 540-001or 531A Strobe (each sold separately). The stanchion is a simple,
attractive, yet highly visible unit measuring 40.5 inches (1.03 meters) tall.
GAI-Tronics enhanced emergency telephones are designed for isolated high-risk areas requiring
emergency communications equipment. Emergency telephone users simply press the clearly labeled
emergency push button for immediate connection to a user-programmed central security telephone
number.
The strobe creates added visibility to emergency telephone locations by providing a constant-on lamp that
automatically flashes when the emergency button is pressed. The telephone is also highly visible; a light
mounted in the stanchion shines on the front of the telephone to illuminate the telephone for nighttime
use.
The Model 234WM-202 Wall-Mount Stanchion Assembly consists of the Model 84505-202 Wall-Mount
Stanchion and the Model 84503-30x Panel Light Assembly (each packaged separately). The strobe and
the emergency telephone are purchased and packaged separately.
GAI-TRONICS 3030 KUTZTOWN RD. READING, PA 19605 USA
610-777-1374 800-492-1212 Fax: 610-796-5954
VISIT WWW.GAI-TRONICS.COM FOR PRODUCT LITERATURE AND MANUALS
Pub. 42004-308G
Model 234WM-202 Wall- Mount Sta nc hi on Ass embly Page 2 of 11
Installation
The following sections provide information on the installation of the complete wall-mount stanchion.
Fig
ure 1. Model 234WM-202 Wall-Mount Stanchion Assembly
p:\standard ioms - current release\42004 instr. manuals\42004-308g.docx
04/16
Pub. 42004-308G
Model 234WM-202 Wall- Mount Sta nc hi on Ass embly Page 3 of 11
Model 84505-202 Wall-Mount Stanchion Installation
1. Remove and save the two tamper-resistant screws at the top of the stanchion. See Figure 1.
OTE: GAI-Tronics Model 233-001 Security Screwdriver (sold separately) is required to remove the
N
tamper-resistant screws.
2. Remove the wall-mounting assembly from the front panel assembly. Refer to Figure 1. Detach the
chain from the wall-mounting assembly. See Figure 2.
3. Enlarge the conduit entry pilot hole(s) to be used for the stanchion power cables. See Figure 3.
4. Fasten the wall-mounting assembly to a wall or flat surface that can support at least 50 pounds, using
3/8-inch bolts. Refer to Figure 2 for mounting hole dimensions and ADA height requirements.
p:\standard ioms - current release\42004 instr. manuals\42004-308g.docx
04/16
Figure 2. Wall Mounting Instructions
Pub. 42004-308G
Model 234WM-202 Wall- Mount Sta nc hi on Ass embly Page 4 of 11
Grounding Requirements
This unit must be grounded in accordance with the National Electrical Code (NEC) in the United States or
the Canadian Electrical Code (CEC) in Canada. A #10 grounding stud has been provided at the base of
the stanchion for grounding. Connect the #10 grounding stud to a grounding electrode. A grounding
electrode rod is typically 8 feet (2.44 m) long per NEC 250, or 9.84 feet (3 m) long per CEC Rule 10.
Figure 3. Conduit/Surge Protection Locations
p:\standard ioms - current release\42004 instr. manuals\42004-308g.docx
04/16
Loading...