GAI-Tronics 12566-001 User Manual

Pub. 42003-082

GAI-TRONICS® CORPORATION

A HUBBELL COMPANY

Single Hub Replacement Kit

Model 12566-001

Confidentiality Notice

This manua l is provide d sole ly as an operatio nal, installation, and ma inte nance guide and conta ins
sensitive business and t e chnical informatio n tha t is confidentia l and pr opri et ary to GAI- Tronics.
GAI-Tronics retains all intellectual property and other rights in or to the information contained herein,
and such information may only be used in connection with the operation of your GAI-Tronics product or
system. This manu al may not be dis clos e d in any form, in whole or in pa rt, direct ly or i ndir ectly, to a ny
third pa r ty.

General Information

This kit is used on stations with cast aluminum enclosures. This kit includes the following components:

Qty Description

1 Single 1.25-inch Hub
1 Gasket, Flat Hub
1 Gasket, Tapered Hub
4 Screw

N

OTE: Before installing this kit, disconnect the supply voltage to the station.

Installation

Removing the Old Hub

1. Loosen the four screws securing the handset or speaker amplifier assembly to the rear enclosure, and

unplug the station.

2. Note the location of the internal wiring as it will have to be reconnected after installing the new hub.

The wiring instructions can also be found in the original installation manual for the enclosure.
Disconnect the internal wiring. DO NOT allow the terminal ends to touch one another. Electrical
tape should be used to insulate the terminals from each other.

3. Remove the conduit from the hub to be replaced.

4. Remove and discard the four screws securing the hub to the enclosure.

GAI-Tronics Corporation P.O. Box 1060, Readi ng, PA 19607-1060 USA

610-777-1374  800-492-1212  Fax: [phone]

ISIT WWW.GAI-TRONICS.COM FOR PRODUCT LITERATURE AND MANUALS

V

Pub. 42003-082

M

ODEL 12566-001 SINGLE HUB REPLACEMENT KIT Page: 2 of 2

Installing the New Hub

1. Identify which of the gaskets you will need to use. One gasket is designed for enclosures with a

tapered bottom; the other is designed for enclosures with a flat bottom. You will use only one of
th es e g a s k et s .

2. Align the holes in the gasket with the openings in the hub.

3. Alig n the hu b/gasket on th e enclosure, and sec ure it using the 4 new screws. Ma ke sure the gasket is

between the hub and the enclosure.

4. Reinstall the conduit to the new hub.

5. Reattach the internal wiring. Reference the original installation manual for the enclosure for the

wiring details.

6. Reattach the amplifier.

7. Reapply the supply voltage to the station.

\\s_eng\gtc proddoc s \st andard iom s - current release\42003 kit manuals \ 42003-082. doc
1991

Warranty

Equipment. GAI-Tronics warrants for a period of one (1) year from the date of shipment, that any

GAI-Tronics equipment supplied hereunder shall be free of defects in material and workmanship, shall
comply with the then-current product specifications and product literature, and if applicable, shall be fit
for the purpose specified in the agreed-upon quotation or proposal document. If (a) Seller’s goods prove
to be defective in workmanship and/or material under normal and proper usage, or unfit for the purpose
specified and agreed upon, and (b) Buyer’s claim is made within the warranty period set forth above,
Buyer may return such goods to GAI-Tronics’ nearest depot repair facility, freight prepaid, at which time
they will be repaired or replaced, at Seller’s option, without charge to Buyer. Repair or replacement shall
be Buyer’s sole and exclusive remedy. The warranty period on any repaired or replacement equipment
shall be the greater of the ninety (90) day repair warranty or one (1) year from the date the original
equipment was shipped. In no event shall GAI-Tronics warranty obligations with respect to equipment
exceed 100% of the total cost of the equipment supplied hereunder. Buyer may also be entitled to the
manufacturer’s warranty on any third-party goods supplied by GAI-Tronics hereunder. The applicability
of any such third-party warranty will be determined by GAI-Tronics.

Services. Any services GAI-Tronics provides hereunder, whether directly or through subcontractors,

shall be performed in accordance with the standard of care with which such services are normally
provided in the industry. If the services fail to meet the applicable industry standard, GAI-Tronics will
re-perform such services at no cost to buyer to correct said deficiency to Company's satisfaction provided
any and all issues are identified prior to the demobilization of the Contractor’s personnel from the work
site. Re-performance of services shall be Buyer’s sole and exclusive remedy, and in no event shall GAI­Tronics warranty obligations with respect to services exceed 100% of the total cost of the services
provided hereunder.

Warranty Periods. Every claim by Buyer alleging a defect in the goods and/or services provided

hereunder shall be deemed waived unless such claim is made in writing within the applicable warranty
periods as set forth above. Provided, however, that if the defect complained of is latent and not
discoverable within the above warranty periods, every claim arising on account of such latent defect shall
be deemed waived unless it is made in writing within a reasonable time after such latent defect is or
should have been discovered by Buyer.

Limitations / Exclusions. The warranties herein shall not apply to, and GAI-Tronics shall not be

responsible for, any damage to the goods or failure of the services supplied hereunder, to the extent
caused by Buyer’s neglect, failure to follow operational and maintenance procedures provided with the
equipment, or the use of technicians not specifically authorized by GAI-Tronics to maintain or service the
equipment. THE WARRANTIES AND REMEDIES CONTAINED HEREIN ARE IN LIEU OF AND
EXCLUDE ALL OTHER WARRANTIES AND REMEDIES, WHETHER EXPRESS OR IMPLIED BY
OPERATION OF LAW OR OTHERWISE, INCLUDING ANY WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

Return Policy

If the equipment requires service, contact your Regional Service Center for a return authorization number
(RA#). Equipment should be shipped prepaid to GAI-Tronics with a return authorization number and a
purchase order number. If the equipment is under warranty, repairs or a replacement will be made in
accordance with the warranty policy set forth above. Please include a written explanation of all defects to
assist our technicians in their troubleshooting efforts.

Call 800-492-1212 (inside the USA) or 610-777-1374 (outside the USA) for help identifying the
Regional Service Center closest to you.

(Rev. 10/06)