GAI-Tronics 12518-101 User Manual
Pub. 42003-165
GAI-TRONICS® CORPORATION
A HUBBELL COMPANY
PCBA, Keypad, and Seal
Replacement Kit
MODEL 12518-101
Confidentiality Notice
This manual is pr ovided s olely as a n op erat ional, installation, and maintenance guide and contains sens itive
bus ines s and t echnic al infor ma tion which is conf idential and propriet ary to GAI-Tronics. GAI - Tronic s
retains a ll intellectual pr operty and other rights in or to t he inf ormation c ontained herein, and s uch
informa tion may only be used in connection wit h the operation of you r GAI- Tronic s pr oduct or system.
This ma nual may not be disclosed in any form, in whole or in p art, dir ec tly or indirectly, to any t hird pa rty.
General Information
The mat erial included in this kit are replacement p art s for the following telephone models:
Model Description
240 Rugged Telephone (Met al)
246 Rugged Telephone (Non-metallic)
250 Rugged Telephone
256 Rugged Telephone
KIT CONTENTS
The Model 12518-101 PCBA Replacement Kit includes the following materials:
Item Quantity Description
1 1 Telephone P rinted C ircui t Board Assembly ( PCBA)
2 1 Keypad Sealing P anel
3 2 #
4 4 #
-40 × 3/8-inch machine screw (for att aching PCBA)
4
-40 × 7/8-inch machine screw (for att aching PCBA)
4
1
5 2 Spacer -
GAI-Tronics Corporation P.O. Box 1060, Reading, PA 19607-1060 USA
610-777-1374 800-492-1212 Fax : 610-796-5954
ISIT WWW.GAI-TRONICS.COM FOR PRODUCT LITERATURE AND MANUALS
V
/
8-inch
Pub. 42003-165
M
ODEL 12518-101 PCBA, KEYPAD, AND SEAL REPLACEMENT KIT Page: 2 of 2
Removing the Existing PCBA and Keypad
1. Loosen t he f our front c over screws.
2. Pull out the front panel assembly about 6–8 inches. Disconnect t he modular telephone cord.
3. Disconnect the ha ndset, hookswitch, ringer, and keypad wires from the pr inted circ uit b oard ass embly
(PCBA).
4. Remove the six screws securing the PCBA.
5. Remove the PC BA, gasket, and the keypad sealing p anel. Di scard the PCBA and seal.
Installing the New Keypad Seal and PCBA
1. Attach a nd secur e the keypad s eal and PCBA ont o the front cover u sing the fou r #4 - 40 × 7/8-inch
screws.
2. Sli d e the
using the two #4 - 40 ×
1
/8-inch sp acer s on top of the standoffs loc ated a t the bottom of the b oard, and f ast en in p lace
3
/8-inch screws provided in this kit.
3. Make the following connections to the PCBA ter mina l strip.
Handset Hookswitch Ringer
Terminal Wire Terminal Wire Terminal Wire
E1 Red E5 Blue E7 Black
E2 Green E6 White E8 Gray
E3 White
E4 Black
4. Connect the modular telephone cord t o the PCBA terminal str ip.
5. Replace the front cover as sembly onto the rear enc losur e. Replace and tighten the f ou r front cover
screws.
6. Check telephone for dial tone.
\\s_eng\gtc proddoc s \ s tandard ioms - current release\ 42003 k it m anuals \42003-165.doc
9/97
Loading...