GAI-Tronics 12513-006 User Manual

Pub. 42003-021A

GAI-TRONICS® CORPORATION

A HUBBELL COMPANY

Valox® Door Replacement Kit

MODELS 12513-001 AND 12513-006

Confidentiality Notice

This manual is pr ovided s olely as a n op erat ional, installation, and maintenance guide and contains sens itive
bus ines s and t echnic al infor ma tion which is conf idential and propriet ary to GAI-Tronics. GAI - Tronic s
retains a ll intellectual pr operty and other rights in or to t he inf ormation c ontained herein, and s uch
informa tion may only be used in connection wit h the operation of you r GAI- Tronic s pr oduct or system.
This ma nual may not be disclosed in any form, in whole or in p art, dir ec tly or indirectly, to any t hird pa rty.

General Information

The Model 12513-006 Valox® Door Repla cement K i t servic es the followi n g :
Model 256 Series, 257, and 258. Model 12513-001 services the Models 9081 and 9085.

NOTE: The Model 12513-001 Kit is NOT approved for use on telephones (256 Series, 257 and 258). Use
of this kit will violate UL 1459. If you ordered this kit for a telephone, please excha nge it f or kit M odel
12513-006. This kit includes the following components:

Qty Description

1 Door
8 Stainless steel screw
8 ¼-inch washer
1 Left lif t-off hinge
1 Right lift-of f hinge

A ¼-inch Allen wrench is needed to install this kit.

Installation

1. Open the enclosure door to acces s the hinge screws.

2. Loosen a nd remove the two sc rews fast ening t he lower hinge on the mid-sect ion of the enclosure, and

remove the hinge.

3. Lift up and remove the old door.

4. Loosen a nd remove the two sc rews securing the remaining hinge to the mid-section of the enclosure.

Remove and discard the hinge.

GAI-Tronics Corporation P.O. Box 1060, Reading, PA 19607-1060 USA

610-777-1374  800-492-1212  Fax : [phone]

ISIT WWW.GAI-TRONICS.COM FOR PRODUCT LITERATURE AND MANUALS

V

Pub. 42003-021A

V

ALOX® DOOR REPLACEMENT KIT Page: 2 of 2

5. Fasten the new upper male hinge half to the mid-section of the enclosure.

6. Posi tion the new door by mating the upper hinge halves.

7. Mate the lower male hinge ha lf with the door hinge half, and position it in p lace with t he mid-s ection.

Fasten them with the two new screws.

8. To adjust as neces sary, loos en t he screws , shift the hinge; retighten the scr ews and close the door.

\\s_eng\gtc proddoc s \ s tandard ioms - current release\ 42003 k it m anuals \42003-021a.doc

2/97

Warranty

Equipment. GAI-Tronics warrants for a period of one (1) year from the date of shipment, that any

GAI-Tronics equipment supplied hereunder shall be free of defects in material and workmanship, shall
comply with the then-current product specifications and product literature, and if applicable, shall be fit
for the purpose specified in the agreed-upon quotation or proposal document. If (a) Seller’s goods prove
to be defective in workmanship and/or material under normal and proper usage, or unfit for the purpose
specified and agreed upon, and (b) Buyer’s claim is made within the warranty period set forth above,
Buyer may return such goods to GAI-Tronics’ nearest depot repair facility, freight prepaid, at which time
they will be repaired or replaced, at Seller’s option, without charge to Buyer. Repair or replacement shall
be Buyer’s sole and exclusive remedy. The warranty period on any repaired or replacement equipment
shall be the greater of the ninety (90) day repair warranty or one (1) year from the date the original
equipment was shipped. In no event shall GAI-Tronics warranty obligations with respect to equipment
exceed 100% of the total cost of the equipment supplied hereunder. Buyer may also be entitled to the
manufacturer’s warranty on any third-party goods supplied by GAI-Tronics hereunder. The applicability
of any such third-party warranty will be determined by GAI-Tronics.

Services. Any services GAI-Tronics provides hereunder, whether directly or through subcontractors,

shall be performed in accordance with the standard of care with which such services are normally
provided in the industry. If the services fail to meet the applicable industry standard, GAI-Tronics will
re-perform such services at no cost to buyer to correct said deficiency to Company's satisfaction provided
any and all issues are identified prior to the demobilization of the Contractor’s personnel from the work
site. Re-performance of services shall be Buyer’s sole and exclusive remedy, and in no event shall GAI­Tronics warranty obligations with respect to services exceed 100% of the total cost of the services
provided hereunder.

Warranty Periods. Every claim by Buyer alleging a defect in the goods and/or services provided

hereunder shall be deemed waived unless such claim is made in writing within the applicable warranty
periods as set forth above. Provided, however, that if the defect complained of is latent and not
discoverable within the above warranty periods, every claim arising on account of such latent defect shall
be deemed waived unless it is made in writing within a reasonable time after such latent defect is or
should have been discovered by Buyer.

Limitations / Exclusions. The warranties herein shall not apply to, and GAI-Tronics shall not be

responsible for, any damage to the goods or failure of the services supplied hereunder, to the extent
caused by Buyer’s neglect, failure to follow operational and maintenance procedures provided with the
equipment, or the use of technicians not specifically authorized by GAI-Tronics to maintain or service the
equipment. THE WARRANTIES AND REMEDIES CONTAINED HEREIN ARE IN LIEU OF AND
EXCLUDE ALL OTHER WARRANTIES AND REMEDIES, WHETHER EXPRESS OR IMPLIED BY
OPERATION OF LAW OR OTHERWISE, INCLUDING ANY WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

Return Policy

If the equipment requires service, contact your Regional Service Center for a return authorization number
(RA#). Equipment should be shipped prepaid to GAI-Tronics with a return authorization number and a
purchase order number. If the equipment is under warranty, repairs or a replacement will be made in
accordance with the warranty policy set forth above. Please include a written explanation of all defects to
assist our technicians in their troubleshooting efforts.

Call 800-492-1212 (inside the USA) or 610-777-1374 (outside the USA) for help identifying the
Regional Service Center closest to you.

(Rev. 10/06)