GAI-Tronics 12251-001 User Manual

Pub. 42003-116A

GAI-TRONICS® CORPORATION

A HUBBELL COMPANY

Modification Kit for G AI-Tro ni cs

Non-Metallic Enclosure Door Spring

Model 12251-001

Confidentiality Notice

This manua l is provide d sole ly as an operatio nal, installation, and ma inte nance guide and conta ins se nsitive
business and technical information that is confidential and proprietary to GAI-Tronics. GAI-Tronics
retains all intellectual property and other rights in or to the information contained herein, and such
information may only be used in connection with the operation of your GAI-Tronics product or system.
This manua l may not be dis closed in any form, i n whol e or in part, directly or indirect ly, t o any t hird party.

General Information

The Model 12251-001 Modification Kit is used on the following Page/Party® models and enclosures:

• 10444-003 • 660-102 • 659-101 • 730-104 • 730-106 • 7335-005

• 730-107 • 733-001 • 733-002 • 733-003 • 7335-001 • 7335-006

• 7335-002 • 7335-003 • 7305-104 • 7305-105 • 7305-107 • 7335-007

• 785-001 • 785-002 • 7855-001 • 7855-002 • 7335-004

This model is also used on the following stations:

• Model 476-001 Electro-Sound Station

• Model 473-002 Centra-Page Station

Installation

1. Units with stainless steel roll pin: Remove the lower

hinge by driving the pin out with a 5/32-inch pin punch.

Units with Telflon

cutting t he pi n off be low pin retain er using a kn ife or
chisel.

2. Ream the hole using a 0.187-inch diameter drill.

®

pin: Remove the lower hinge by

3. Refer to Figure 1. Position the spring as shown. Align the

coils of the spring with hinge hole while sliding new hinge
pin into the assembly.

4. Press new retainers into new hinge pin using a 3/16-inch

hex socket wrench. Leave a 1/16-inch clearance between
retainers and the spring.

GAI-Tronics Corporation P.O. Box 1060, Readi ng, PA 19607-1060 USA

610-777-1374  800-492-1212  Fax: [phone]

ISIT WWW.GAI-TRONICS.COM FOR PRODUCT LITERATURE AND MANUALS

V

Figure 1. Ass e mbly Details

Warranty

Equipment. GAI-Tronics warrants for a period of one (1) year from the date of shipment, that any

GAI-Tronics equipment supplied hereunder shall be free of defects in material and workmanship, shall
comply with the then-current product specifications and product literature, and if applicable, shall be fit
for the purpose specified in the agreed-upon quotation or proposal document. If (a) Seller’s goods prove
to be defective in workmanship and/or material under normal and proper usage, or unfit for the purpose
specified and agreed upon, and (b) Buyer’s claim is made within the warranty period set forth above,
Buyer may return such goods to GAI-Tronics’ nearest depot repair facility, freight prepaid, at which time
they will be repaired or replaced, at Seller’s option, without charge to Buyer. Repair or replacement shall
be Buyer’s sole and exclusive remedy. The warranty period on any repaired or replacement equipment
shall be the greater of the ninety (90) day repair warranty or one (1) year from the date the original
equipment was shipped. In no event shall GAI-Tronics warranty obligations with respect to equipment
exceed 100% of the total cost of the equipment supplied hereunder. Buyer may also be entitled to the
manufacturer’s warranty on any third-party goods supplied by GAI-Tronics hereunder. The applicability
of any such third-party warranty will be determined by GAI-Tronics.

Services. Any services GAI-Tronics provides hereunder, whether directly or through subcontractors,

shall be performed in accordance with the standard of care with which such services are normally
provided in the industry. If the services fail to meet the applicable industry standard, GAI-Tronics will
re-perform such services at no cost to buyer to correct said deficiency to Company's satisfaction provided
any and all issues are identified prior to the demobilization of the Contractor’s personnel from the work
site. Re-performance of services shall be Buyer’s sole and exclusive remedy, and in no event shall GAI­Tronics warranty obligations with respect to services exceed 100% of the total cost of the services
provided hereunder.

Warranty Periods. Every claim by Buyer alleging a defect in the goods and/or services provided

hereunder shall be deemed waived unless such claim is made in writing within the applicable warranty
periods as set forth above. Provided, however, that if the defect complained of is latent and not
discoverable within the above warranty periods, every claim arising on account of such latent defect shall
be deemed waived unless it is made in writing within a reasonable time after such latent defect is or
should have been discovered by Buyer.

Limitations / Exclusions. The warranties herein shall not apply to, and GAI-Tronics shall not be

responsible for, any damage to the goods or failure of the services supplied hereunder, to the extent
caused by Buyer’s neglect, failure to follow operational and maintenance procedures provided with the
equipment, or the use of technicians not specifically authorized by GAI-Tronics to maintain or service the
equipment. THE WARRANTIES AND REMEDIES CONTAINED HEREIN ARE IN LIEU OF AND
EXCLUDE ALL OTHER WARRANTIES AND REMEDIES, WHETHER EXPRESS OR IMPLIED BY
OPERATION OF LAW OR OTHERWISE, INCLUDING ANY WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

Return Policy

If the equipment requires service, contact your Regional Service Center for a return authorization number
(RA#). Equipment should be shipped prepaid to GAI-Tronics with a return authorization number and a
purchase order number. If the equipment is under warranty, repairs or a replacement will be made in
accordance with the warranty policy set forth above. Please include a written explanation of all defects to
assist our technicians in their troubleshooting efforts.

Call 800-492-1212 (inside the USA) or 610-777-1374 (outside the USA) for help identifying the
Regional Service Center closest to you.

(Rev. 10/06)