Page 1
Pub. 42004-464B
GAI-TRONICS® CORPORATION
A HUBBELL COMPANY
Model 10458-701 and 10458-801 VoIP &
VoIP WiFi Electronic Paging Modules
T ABLE OF C ONTENTS
Foreword .........................................................................................................................................1
Scope of Manual ...................................................................................................................................... 1
Nomenclature .......................................................................................................................................... 1
Ordering Replacement Parts ................................................................................................................. 1
Service and Repair .................................................................................................................................. 1
Confidentiality Notice ............................................................................................................................. 2
FCC Licensing Information ................................................................................................................... 2
Computer Software Copyrights ............................................................................................................. 3
Warranty ................................................................................................................................................. 3
Safety and General Information ............................................................................................................ 4
Operational Cautions .............................................................................................................................. 5
Safe Handling of CMOS Integrated Circuit Devices ........................................................................... 6
General Information .......................................................................................................................7
Product Overview ................................................................................................................................... 7
Features and Functions .......................................................................................................................... 8
Available Models ..................................................................................................................................... 8
System Requirements and Limitations ................................................................................................. 9
Replacement Parts and Kits ................................................................................................................. 10
Performance Specifications ..........................................................................................................10
Programming and Set Up .............................................................................................................12
Opening the VoIP Paging Module Assembly ..................................................................................... 12
WiFi Interface Setup (Model 10458-801) ............................................................................................ 14
VoIP PCBA Configuration ................................................................................................................... 17
VoIP PCBA Initial Network Configuration ........................................................................................................ 17
Closing the VoIP Electronic Paging Module ...................................................................................... 17
Installation ....................................................................................................................................18
Safety and General Information .......................................................................................................... 18
Outdoor Installation Product ............................................................................................................................... 19
Antenna Care ...................................................................................................................................................... 19
Electromagnetic Interference/Compatibility ....................................................................................................... 19
GAI-Tronics Corporation 400 E. Wyomissing Ave. Mohnton, PA 19540 USA
610-777-1374 800-492-1212 Fax: 610-796-5954
V
ISIT WWW.GAI-TRONICS.COM FOR PRODUCT LITERATURE AND MANUALS
Page 2
TABLE OF CONTENTS P UB. 42004-464B
Mechanical Receipt Inspection ............................................................................................................ 19
Cable Installation Safety Considerations ............................................................................................ 19
Mounting ................................................................................................................................................ 19
Field Wiring ........................................................................................................................................... 22
Power Connection ............................................................................................................................................... 22
Speaker Connection ............................................................................................................................................ 22
Output Contact Connections ............................................................................................................................... 22
Opto Output Connection ..................................................................................................................................... 22
Antenna Connection............................................................................................................................................ 23
GAI-Tronics Corporation 400 E. Wyomissing Ave. Mohnton, PA 19540 USA
610-777-1374 800-492-1212 Fax: 610-796-5954
V
ISIT WWW.GAI-TRONICS.COM FOR PRODUCT LITERATURE AND MANUALS
Page 3
Pub. 42004-464B
GAI-TRONICS® CORPORATION
A HUBBELL COMPANY
Model 10458-701 and 10458-801 VoIP
& VoIP WiFi Electronic Paging Modules
Foreword
Scope of Manual
This manual offers descriptive data and service information for the VoIP Electronic Paging Modules.
Nomenclature
The model number, located on the nameplate on top of the speaker, specifically identifies GAI-Tronics
equipment.
Ordering Replacement Parts
When ordering replacement parts or requesting equipment information, please include the complete
identification number. This applies to all components, kits, and chassis. If the component part number is
not known, the order should include the number of the chassis or kit of which it is a part and sufficient
description of the desired component to identify it. Order parts from:
Customer Service
GAI-Tronics Corporation
400 E. Wyomissing Ave.
Mohnton, PA 19540
US: 800-492-1212
Outside US: 610-777-1374
Service and R epair
Inoperative or malfunctioning equipment should be returned to the factory for repair. Please call
1-800-492-1212 or 610-777-1374 to obtain a Return Authorization number, published repair prices, and
shipping instructions.
OTE: A purchase order or credit card number is required prior to processing non-warranty repairs.
N
GAI-Tronics Corporation 400 E. Wyomissing Ave. Mohnton, PA 19540 USA
610-777-1374 800-492-1212 Fax: 610-796-5954
V
ISIT WWW.GAI-TRONICS.COM FOR PRODUCT LITERATURE AND MANUALS
Page 4
Pub. 42004-464B
Model 10458-701 and 10458-801 VoIP & VoIP WiFi Electronic Paging Modules Page 2 of 24
Confidentiality Notice
This manual is provided solely as an operational, installation, and maintenance guide and contains
sensitive business and technical information that is confidential and proprietary to GAI-Tronics.
GAI-Tronics retains all intellectual property and other rights in or to the information contained herein,
and such information may only be used in connection with the operation of your GAI-Tronics product or
system. This manual may not be disclosed in any form, in whole or in part, directly or indirectly, to any
third party.
FCC Licensing In formation
Your radio operates on General Mobile Radio Service (GMRS), Private Land Mobile Radio Service,
Amateur Radio Service, Aeronautical Mobile, or Maritime Mobile Service frequencies and is subject to
the Rules and Regulations of the Federal Communications Commission (FCC). The FCC requires that all
operators using such frequencies obtain a radio license before operating their equipment. To obtain the
FCC forms, go to http://wireless.fcc.gov/services/personal/generalmobile/index.html
and 159, which include all forms and instructions.
Changes or modifications not approved by GAI-Tronics Corporation may void the user’s authority
granted by the FCC to operate this radio and should not be made. To comply with FCC requirements,
transmitter adjustments should be made only by or under the supervision of a person certified as
technically qualified to perform transmitter maintenance and repairs in the private land mobile and fixed
services as certified by an organization representative of the user of those services. Replacement of any
transmitter component (crystal, semiconductor, etc.) not authorized by the FCC equipment authorization
for this radio could violate FCC rules.
to obtain Forms 605
OTE: Use of this radio outside the country where it was intended to be distributed is subject to
N
government regulations and may be prohibited.
Federal Communications Commission (FCC)
1-202-418-0177 1-800-418-FORM
1-800-418-3676
1-888-CALL-FCC
1-888-225-5322
Or: http://www.fcc.gov
f:\standard ioms - current release\ 42004 instr. manuals\42004-464b.doc
07/14
Page 5
Pub. 42004-464B
Model 10458-701 and 10458-801 VoIP & VoIP WiFi Electronic Paging Modules Page 3 of 24
Computer Softw are Copyrights
This product contains copyrighted computer programs stored in semiconductor memory. These programs
are copyrighted by GAI-Tronics Corporation and may not be reproduced in any form without expressed
written permission from GAI-Tronics.
Warranty
GAI-Tronics warrants for a period of one (1) year from the date of shipment, that any GAI-Tronics equipment supplied hereunder
shall be free of defects in material and workmanship, shall comply with the then-current product specifications and product
literature, and if applicable, shall be fit for the purpose specified in the agreed-upon quotation or proposal document. If (a)
Seller’s goods prove to be defective in workmanship and/or material under normal and proper usage, or unfit for the purpose
specified and agreed upon, and (b) Buyer’s claim is made within the warranty period set forth above, Buyer may return such
goods to GAI-Tronics’ nearest depot repair facility, freight prepaid, at which time they will be repaired or replaced, at Seller’s
option, without charge to Buyer. Repair or replacement shall be Buyer’s sole and exclusive remedy, and the warranty period on
any repaired or replacement equipment shall be one (1) year from the date the original equipment was shipped. In no event shall
GAI-Tronics’ warranty obligations with respect to equipment exceed 100% of the total cost of the equipment supplied hereunder.
The applicability of any such third-party warranty will be determined solely by GAI-Tronics.
Services. Any services GAI-Tronics provides hereunder, whether directly or through subcontractors, shall be performed in
accordance with the standard of care with which such services are normally provided in the industry. If the services fail to meet
the applicable industry standard, GAI-Tronics will, for a period of one (1) year from the date of completion, re-perform such
services at no cost to the Buyer. Re-performance of services shall be Buyer’s sole and exclusive remedy, and in no event shall
GAI-Tronics’ warranty obligations with respect to services exceed 100% of the total cost of services provided hereunder.
Limitations/Exclusions. The warranty on any equipment supplied hereunder is subject to Customer’s use in compliance
with applicable FCC regulations and manufacturer specifications. The warranties herein shall not apply to, and GAI-Tronics
shall not be responsible for, any damage to the goods or failure of the services supplied hereunder, to the extent caused by
accident, misuse, abuse, neglect, system design, product modification, failure to follow instructions contained in the product
manual, repair, or attempted repair by anyone not authorized by GAI-Tronics, improper installation, installation of parts that do
not conform to the quality or specifications of the original parts or accessories, damage or loss occurred during shipment, or any
unit which is not new when sold or upon which the serial number has been defaced, modified or removed. The warranty does not
extend to damage incurred by natural causes including Force Majeure. The warranty does not cover microprocessors if failure is
due to static damage or application of improper voltage. THE WARRANTIES AND REMEDIES CONTAINED HEREIN ARE
IN LIEU OF AND EXCLUDE ALL OTHER WARRANTIES AND REMEDIES, WHETHER EXPRESS OR IMPLIED BY
OPERATION OF LAW OR OTHERWISE, INCLUDING ANY WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE.
Operational and Maintenance Procedures. Buyer acknowledges that any improper use, maintenance, or
modification of the equipment provided hereunder, or use of unqualified maintenance or service technicians will severely impair
the operational effectiveness of the entire communication system. Buyer hereby agrees to indemnify, defend and hold GAITronics harmless from and against any and all third party claims arising, in any manner, out of: (a) Buyer’s neglect of the
equipment; (b) Buyer’s use of technicians not authorized by GAI-Tronics to service the equipment; or (c) Buyer’s improper use
or modification of the equipment or failure to follow the operational and maintenance procedures provided with the equipment.
Limitation of Liability/Damages. In no event (even should circumstances cause the exclusive warranties and remedies
set forth in the Warranty section to fail of their essential purpose) shall either party be liable for any indirect, incidental, special or
consequential damages (including, but not limited to, loss of use, loss of anticipated profits, or damages arising from delay)
whether such claims are alleged to have arisen out of breach of warranty, breach of contract, strict or absolute liability in tort, or
other act, error or omission, or from any other cause whatsoever, or any combination of the foregoing.
f:\standard ioms - current release\ 42004 instr. manuals\42004-464b.doc
07/14
Page 6
Pub. 42004-464B
Model 10458-701 and 10458-801 VoIP & VoIP WiFi Electronic Paging Modules Page 4 of 24
Safety and General Info rmation
Installation should only be performed by qualified service personnel in accordance with the
National Electrical Code or applicable local codes.
Power Sources - Operate this unit only from the type of power source indicated on the label. If
Outdoor Product:
Power Lines - An outdoor system should not be located in the vicinity of overhead power lines, electric
lights, or power circuits, or where it may contact such power lines or circuits, as this contact might be
fatal. Refer to the National Electrical Code Article 800 regarding installation.
unsure of the type of power supply to use, contact qualified service personnel.
For units intended to operate from battery power, refer to operating instructions.
For units intended to operate with External Power Supplies, use only the recommended
approved power supplies.
For units intended to operate with a limited power source, this power source must comply
with EN60950. Substitutions may damage the unit or cause fire or shock.
User Instructions
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Exposure to Radio Frequency Energy
Your radio is designed to comply with the following standards and guidelines regarding exposure of
human beings to radio frequency electromagnetic energy:
FCC, Code of Federal Regulations; 47 CFR part 2 sub-part J
American National Standards Institute (ANSI)/Institute of Electrical and Electronic Engineers (IEEE)
C95.1-1992
Institute of Electrical and Electronic Engineers (IEEE) C95.1-1999 Edition
International Commission on Non-Ionizing Radiation Protection (ICNIRP) 1998
Ministry of Health (Canada) Safety Code 6. Limits of Human Exposure to Radio Frequency
Electromagnetic Fields in the Frequency Range from 3 kHz to 300 GHz, 1999
f:\standard ioms - current release\ 42004 instr. manuals\42004-464b.doc
07/14
Page 7
Pub. 42004-464B
Model 10458-701 and 10458-801 VoIP & VoIP WiFi Electronic Paging Modules Page 5 of 24
Antenna Care
Unauthorized antennas, modifications, or attachments could damage the radio and may violate FCC
regulations.
Do NOT hold the antenna when the radio is IN USE. Holding the antenna affects the effective range.
Approved Accessories
Only use GAI-Tronics Corporation approved accessories. Please visit www.gai-tronics.com.
Electromagnetic Interference/Compatibility
Electronic equipment may be susceptible to electromagnetic interference. If you experience interference,
visit the FCC website at http://www.fcc.gov
for possible solutions.
Operational Cautions
Hospitals or Health Care Facilities
To avoid electromagnetic interference and/or compatibility conflicts, turn off your radio in any facility
where posted notices instruct you to do so. Hospital or health care facilities may be using equipment that
is sensitive to external RF energy.
Aircraft/Airports
Airports may be using equipment that is sensitive to external RF energy. Any use of a radio must be in
accordance with applicable regulations.
Medical Devices - Pacemakers
These recommendations are consistent with the independent research by, and recommendations of the
U.S. Food and Drug Administration. Persons with pacemakers should:
ALWAYS keep the radio more than six inches (15 cm) from their pacemaker when the radio is turned
ON.
Do NOT carry the radio in the breast pocket.
Turn the radio OFF immediately if you have any reason to suspect that interference is taking place.
Blasting Caps and Areas
To avoid possible interference with blasting operations, turn off your radio when you are near electrical
blasting caps, in a blasting area, or in areas posted: “Turn off two-way radio.” Obey all signs and
instructions.
f:\standard ioms - current release\ 42004 instr. manuals\42004-464b.doc
07/14
Page 8
Pub. 42004-464B
Model 10458-701 and 10458-801 VoIP & VoIP WiFi Electronic Paging Modules Page 6 of 24
Safe Handling of CMOS Integrated Circuit De vices
Many of the integrated circuit devices used in communications equipment are of the Complementary
Metal Oxide Semiconductor (CMOS) type. Because of their high open circuit impedance, CMOS
integrated circuits are vulnerable to damage from static charges. Care must be taken handling, shipping,
and servicing them and the assemblies in which they are used.
Even though protection devices are provided in CMOS integrated circuit inputs, the protection is effective
only against overvoltage in the hundreds of volts range such as is encountered in an operating system. In
a system, circuit elements distribute static charges and load the CMOS circuits, decreasing the chance of
damage. However, CMOS circuits can be damaged by improper handling of the modules, even in a
system.
To avoid damage to circuits, observe the following handling, shipping, and servicing precautions:
1. Prior to and while servicing a circuit module, particularly after moving within the service area,
momentarily touch both hands to a bare metal, earth-grounded surface. This will discharge any static
charge that may have accumulated on the person doing the servicing.
OTE: Wearing a conductive wrist strap will minimize static build-up during servicing.
N
2. Whenever possible, avoid touching any electrically conductive parts of the circuit module with your
hands.
3. Power down the unit before installing or removing the circuit module.
4. When servicing a circuit module, avoid carpeted areas, dry environments, and certain types of
clothing (silk, nylon, etc.) because they contribute to static build-up. Similarly, disconnect the test
probe prior to removing the ground lead.
5. All electrically powered test equipment should be grounded. Apply the ground lead from the test
equipment to the circuit module before connecting the test probe.
6. If a circuit module is removed from the system, it is desirable to lay it on a conductive surface (such
as a sheet of aluminum foil) which is connected to ground through 100k of resistance.
7. When soldering, be sure the soldering iron is grounded and has a grounded tip.
8. Prior to connecting jumpers, replacing circuit components, or touching CMOS pins (if this becomes
necessary in the replacement of an integrated circuit device), be sure to discharge any static build-up
as described in procedure 1. Since voltage differences can exist across the human body, it is
recommended that only one hand be used if it is necessary to touch pins on the CMOS device and
associated board wiring.
9. When replacing a CMOS integrated circuit device, leave the device in its conductive rail container or
conductive foam until it is to be inserted into the printed circuit module.
10. All low impedance test equipment (such as pulse generators, etc.) should be connected to CMOS
device inputs after power is applied to the CMOS circuitry. Similarly, such low impedance
equipment should be disconnected before power is turned off.
11. Replacement modules shipped separately from the factory will be packaged in a conductive material.
Any modules being transported from one area to another should be wrapped in a similar material
(aluminum foil may be used). Never use non-conductive material for packaging these modules.
f:\standard ioms - current release\ 42004 instr. manuals\42004-464b.doc
07/14
Page 9
Pub. 42004-464B
Model 10458-701 and 10458-801 VoIP & VoIP WiFi Electronic Paging Modules Page 7 of 24
General Information
Product Overview
GAI-Tronics’ Electronics Paging Modules are mechanically designed for mounting to the access panel in
Model 234 Series Stanchions. Each Paging Module can be used with the Model 234SBM Stanchion
Broadcast Module or Model 234SBA Stanchion Broadcast Assembly to supply an amplified broadcast to
stanchion speakers.
The Model 10458-701 VoIP Electronic Paging Module enables broadcasting to personnel throughout an
area over an existing VoIP network via the GAI-Tronics 234 Series Stanchion’s integral speakers. The
Model 10458-801 VoIP WiFi Electronic Paging Module provides the same capability as the Model
10458-701 but allows connection to an existing wireless network. The Paging Modules can easily be
added to an existing network (10/100 baseT Ethernet) or wireless network (IEEE 802.11 b/g) with
minimal cost or effort.
The -701 and -801 Paging Modules include an integrated speaker amplifier circuit that can supply up to
30 watts of output power to an existing 8-ohm speaker or combination of speakers equaling 8 ohms. Each
VoIP or VoIP WiFi Electronic Paging Module is capable of providing two dry contact Type A (normally
open) outputs. Each output is programmable for a variety of use such as activation of a strobe or
initiating a door latch remotely.
The GAI-Tronics VoIP and VoIP Electronic Paging Modules provide the flexibility to address a diverse
range of applications. A wide variety of functions can be achieved by altering the configuration data
stored in the non-volatile memory. The configuration options include:
Web page configuration
Configuration file
Command Line Interface (CLI)
f:\standard ioms - current release\ 42004 instr. manuals\42004-464b.doc
07/14
Page 10
Pub. 42004-464B
Model 10458-701 and 10458-801 VoIP & VoIP WiFi Electronic Paging Modules Page 8 of 24
Fea tures and Functions
The GAI-Tronics Models 10458-701 VoIP and 10458-801 VoIP WiFi Electronic Paging Modules are
equipped with the following features:
Wired or WiFi VoIP
One-way broadcasting from IP network
30-watt speaker amplifier output (into an 8-ohm
speaker load) with 120/240 V ac power input
8-watt speaker amplifier output (into an 8-ohm
speaker load) with PoE input
Two dry contact closure outputs
SIP compatible (RFC3261)
Real-time alarm reporting via email, Syslog, or
TMA software
Configurable via web page, serial link or
download
Multicast capability, up to eight addresses
Available Mode ls
Table 1. VoIP & VoIP WiFi Electronic Paging Module Model Chart
Part No. Description
10458-701 VoIP Electronic Paging Module, 30 W (8-ohm load)
10458-801 VoIP WiFi Electronic Paging Module, 30 W (8-ohm load)
Figure 1. Model 10458-801 Outline Diagram
f:\standard ioms - current release\ 42004 instr. manuals\42004-464b.doc
07/14
Page 11
Pub. 42004-464B
Model 10458-701 and 10458-801 VoIP & VoIP WiFi Electronic Paging Modules Page 9 of 24
System Requ irements and Limitatio ns
A 100 baseT Ethernet with SIP Server is required for systems containing three or more VoIP Paging
Modules. The operation of this equipment is limited by the customer’s LAN media capabilities and the
services available at each end point. The performance of each module is dependent on the provision of
sufficient bandwidth and prioritization on the network to give the quality of service required. In addition,
the setup, installation, and software version of key components such as switches and routers can have a
significant effect on the operation of this equipment. Improper connections or loose cables can also affect
their operation.
The VoIP and WiFi Paging Modules require a local 120/240 V ac power source for operation.
The following network facilities should be provided (This may vary widely depending on how your
network is deployed):
SIP proxy server (to route calls)
SIP registrar server (frequently combined with proxy servers)
TFTP server (for downloading configuration files).
TCP Syslog server (for reporting alarms and external inputs)
SMTP server (for reporting via email)
STNP server (to synchronize the internal clock)
STUN server (for NAT firewall traversal)
Dedicated systems, such as Gatekeepers, VoIP-enabled PABXs or soft PABXs may also provide these
functions.
The GAI-Tronics VoIP Interfaces only support Session Initiation Protocol (SIP) to RFC3261 Call Control
signaling.
In addition to direct access, peer-to-peer or via a SIP server, each interface/amplifier is capable of
receiving a Multicast broadcast. Multicast allows a single audio stream to be sent to multiple end points
simultaneously, to achieve multi-point paging or Public Address functionality over IP. Multicast requires
the use of a SIP server that specifically supports Multicast functionality and each interface must be
configured (enabled) to receive Multicast packets.
f:\standard ioms - current release\ 42004 instr. manuals\42004-464b.doc
07/14
Page 12
Pub. 42004-464B
Model 10458-701 and 10458-801 VoIP & VoIP WiFi Electronic Paging Modules Page 10 of 24
Replac ement Parts and Kits
Table 2. Spare Parts List
Part No. Description 10458-701 10458-801
100-02-7013-000
69625-001 VoIP Broadcast Carrier PCBA
69868-001 Ethernet Wireless Interface PCBA
40404-081
12234-102
VoIP PCBA
Power Supply PCBA
WiFi Antenna/Lens Kit
(for use with 234 series Stanchion)
Perf ormance Specificat ions
Power Options
AC Power
Input voltage ............................................................................................................. 120/240 V ac, 50/60 Hz
Input current ...................................................................................... 0.35 A @ 120 V ac, 0.2 A @ 240 V ac
Power over Ethernet (PoE) (Model 10458-701 only)
Power ............................................................................................................... 802.3af compliant (via RJ45)
Audio
Output
Speaker output power
With PoE .............................................................................................................. 8 W into 8-ohm load
With 120/240 V ac input .................................................................................... 30 W into 8-ohm load
Frequency response .................................................................................................................... 300–3000 Hz
Network (Ethernet)
Signaling ....................................................................................... SIP (RFC3261 compliant) Loose routing
Configuration .............................................................................................................. Embedded web server
Embedded Telnet server
Configuration file download
Configuration file building tool (Vconf.exe)
Direct serial connection
(Nine-way D-type female connector)
Command line interface
SNTP with time zone and daylight saving
Automatic updating via TFTP
Password protection
Control Outputs
Output 1 (isolated solid state switch) ..........................................50 milliamps @ 30 V ac/dc (resistive load)
Output 2 (isolated SPST relay) .......................................................... 10 amps @ 30 V ac/dc (resistive load)
f:\standard ioms - current release\ 42004 instr. manuals\42004-464b.doc
07/14
Page 13
Pub. 42004-464B
Model 10458-701 and 10458-801 VoIP & VoIP WiFi Electronic Paging Modules Page 11 of 24
WiFi Module (Model 10458-801 only)
Antenna (part of Model 12234-102 Antenna Lens Kit, purchased separately) .................. 2.4 GHz, 2.0 dBi,
50-ohm, omni-directional,
¼ wavelength dipole configuration, VSWR <
2.0
Standards .............................................................................................................. Wireless 802.11b, 802.11g
Static IP provisioning or DHCP STUN client (NAT traversal)
Frequency ............................................................................................................... Europe 2.412–2.472 GHz
USA 2.412–2.462 GHz
Antenna connector ................................................................................................................................. BNC
Mechanical
Physical dimensions ................................... 4.50 W 7.00 D 7.63 H inches; (114.3 177.8 193.8 mm)
Enclosure material ...................................................................................................... 0.062 thick aluminum
Connections......................................................................................................... Screw type terminal blocks
Shipping weights
Model 10458-701 ................................................................................................................. 4.5 lbs. (2.04 kg)
Model 10458-801 ................................................................................................................. 5.0 lbs. (2.27 kg)
Environmental
Temperature range ................................................................................. −4º F to +140º F (−20º C to +60º C)
Humidity ............................................................................................................ Up to 95%, non-condensing
Approval Standards
USA .............................................................. FCC Modular Approval, FCC ID: FCC ID: XM5-SM2144N1
CFR Title 47 FCC Part 15, Subpart B and C
Canada ............................................................... Industry Canada Module Approval IC: 8516A-SM2144N2
Industry Canada ICES-003, RSS-Gen, RSS-210
EU ............................................................................................. EN 300 328 (R&TTE Directive 1999/5/EC)
EN 301 489 (EMC Directive 2004/108/EC)
f:\standard ioms - current release\ 42004 instr. manuals\42004-464b.doc
07/14
Page 14
Pub. 42004-464B
Model 10458-701 and 10458-801 VoIP & VoIP WiFi Electronic Paging Modules Page 12 of 24
Programming and Set Up
NOTE: The 10458-701 and -801VoIP and VoIP WiFi Electronic Paging Modules include the same
embedded browser as do GAI-Tronics’ VoIP and WiFi telephones. There are many programmable
parameters utilized by our telephones that are not utilized by the VoIP Paging Modules. All Paging
Modules are factory programmed for maximum operating proficiency. Please do not make any
programming changes other than those directed in this manual.
Opening the VoIP Paging Module Assembly
The VoIP Paging Module must be opened for programming and installation. Bench programming and
testing is recommended. Remove the assembly from the carton and position on a flat surface.
Remove the four screws (two on top and two on bottom) holding the mounting plate to the chassis. The
mounting plate has two finger holes that can be used to remove it from the chassis. Remove the six
screws that are holding the chassis together (two on the rear and four on the side). Refer to Figure 2
below.
Figure 2: Electronic Paging Module Assembly (Model 10458-701 shown)
f:\standard ioms - current release\ 42004 instr. manuals\42004-464b.doc
07/14
Page 15
Pub. 42004-464B
Model 10458-701 and 10458-801 VoIP & VoIP WiFi Electronic Paging Modules Page 13 of 24
Carefully open the chassis, keeping the U-bracket to the right. The VoIP Broadcast Carrier PCBA is
mounted on the U-bracket and is where the settings and adjustments exist. Refer to Figure 3.
Figure 3: Electronic Paging Module (opened)
f:\standard ioms - current release\ 42004 instr. manuals\42004-464b.doc
07/14
Page 16
Pub. 42004-464B
Model 10458-701 and 10458-801 VoIP & VoIP WiFi Electronic Paging Modules Page 14 of 24
WiFi Interface Setup (Model 10 458-801)
Configuration of the WiFi Interface PCBA is required to set up security of the WLAN unit’s connection.
For first time configuration of the WiFi interface, power the unit by connecting 120/240 V ac to the
chassis connections. Refer to Figure 8. To reconfigure a unit, power the unit and press MSEL button,
PB1, on the WiFi Interface PCBA for 20 seconds to return the default settings to the PCBA.
Connect to the ad-hoc network GTC using a PC/laptop with a wireless capability. Open a web browser
on PC and type http://192.168.1.3/iChip
In the following webpage enter password for the password to enter configuration of the WiFi interface
PCBA.
into the address field.
Figure 4. WiFi Interface Log In Webpage
f:\standard ioms - current release\ 42004 instr. manuals\42004-464b.doc
07/14
Page 17
Pub. 42004-464B
Model 10458-701 and 10458-801 VoIP & VoIP WiFi Electronic Paging Modules Page 15 of 24
Figure 5. WiFi Interface Network Configuration Webpage
f:\standard ioms - current release\ 42004 instr. manuals\42004-464b.doc
07/14
Page 18
Pub. 42004-464B
Model 10458-701 and 10458-801 VoIP & VoIP WiFi Electronic Paging Modules Page 16 of 24
In the Network Configuration page, enter the parameters WLCH, WSTO, WLK1, WLPP and WLSI.
Other settings need not be entered.
WLCH is the Wireless LAN Channel.
WSTO is the Wireless Security Type. The following are the choices:
Table 3. Wireless Security Type Choices
WSTO Setting Wireless Security Type
0 NONE
1 WEP-64
2 WEP-128
3 WPA
4 WPA2
WLK1 is the WEP key. It is ten HEX characters for WEP-64 or 26 HEX characters for WEP-128.
If NONE, WPA or WPA2 are used, leave blank.
WLPP is the Wireless LAN WPA Passphrase. If NONE, WEP-64 or WEP-128 are used leave blank.
WLSI is the SSID of the Access Point you connect to. This entry is case sensitive.
After entering parameters, press “SUBMIT” button to save configuration. Now the VoIP PCBA can be
accessed through the wireless network for configuration.
f:\standard ioms - current release\ 42004 instr. manuals\42004-464b.doc
07/14
Page 19
Pub. 42004-464B
Model 10458-701 and 10458-801 VoIP & VoIP WiFi Electronic Paging Modules Page 17 of 24
VoIP PCBA Configuration
For the first time configuration of the VoIP PCBA, power the unit by connecting 120/240 V ac to chassis
connections and connecting Ethernet port of the VoIP PCBA to a 10/100 base-T Ethernet Network. Refer
to Figure 8.
The easiest way to get started is to make a network connection to the unit and log on via a web browser.
The unit is initially set with a static IP address:
IP address 192.168.1.2
A user name and password will be requested. The initial factory settings are:
User Name user
Password password
Changing the user name and password is recommended. This security measure helps to prevent
unauthorized changes to the VoIP PCBA Interface’s configuration.
N
OTE: The audio output level is set by configuring the Hands-free Output on the Audio Settings
webpage during the configuration of the speaker.
VoIP PCBA Initial Network Configuration
Each VoIP PCBA must be set up for the network prior to installation. Assign a local ID, domain, proxy,
and registrar.
Assign a host name The host name provides identification of the different VoIP PCBAs on the
network.
Test Verify that calls can be made successfully.
Maintain Monitor alarms. Set up auto-updates.
Refer to Pub. 42004-482 for detailed programming instructions of this VoIP device.
Closing the VoIP Electronic Paging Module
Assemble the two chassis sections and tighten the screws.
f:\standard ioms - current release\ 42004 instr. manuals\42004-464b.doc
07/14
Page 20
Pub. 42004-464B
Model 10458-701 and 10458-801 VoIP & VoIP WiFi Electronic Paging Modules Page 18 of 24
Installation
Safety and General Info rmation
Install equipment without modification and according to all applicable local and national electrical codes.
Consult the National Electrical Code (NFPA 70), Canadian Standards Association (CSA 22.1), and local
codes for specific requirements regarding your installation. Class 2 circuit wiring must be performed in
accordance with NEC 725.55.
Read, follow, and retain instructions – All safety and operating instructions should be read and followed
before operating the unit. Retain instructions for future reference.
WARNING
station and any associated equipment before beginning any installation.
CAUTION
approval listing in the “Specifications” section of t his manual . Such installation may cause a safety
hazard and consequent injury or property damage.
Heed warnings – Adhere to all warnings on the unit and in the operating instructions.
Attachments – Attachments not recommended by the product manufacturer should not be used, as they
may cause hazards.
Servicing – Do not attempt to service this unit by yourself. Opening or removing covers may expose you
to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
This permanently connected apparatus must have an ALL-POLE MAINS switch with a contact separation
of at least 3 mm in each pole incorporated in the electrical installation of the building.
This product can contain hazardous voltages. Always remove power to this
Do not install this equipment in areas other than those indicated on the
f:\standard ioms - current release\ 42004 instr. manuals\42004-464b.doc
07/14
Page 21
Pub. 42004-464B
Model 10458-701 and 10458-801 VoIP & VoIP WiFi Electronic Paging Modules Page 19 of 24
Outdoor Installation Product
Power lines - An outdoor system should not be located in the vicinity of overhead power lines, electric
lights, or power circuits, where it may contact such power lines or circuits, as this contact might be fatal.
Refer to the National Electrical Code Article 800 regarding installation.
Antenna Care
Unauthorized antennas, modifications, or attachments could damage the radio and may violate FCC
regulations.
Electromagnetic Interference/Compatibility
Electronic equipment may be susceptible to electromagnetic interference. If you experience interference,
visit the FCC website at http://www.fcc.gov for possible solutions.
Mechanical Receipt Inspection
The Paging Modules are shipped in a cardboard container, protected from movement and distress by a
self-forming packaging material. Thoroughly inspect it as soon as possible after delivery. In-transit
damage should be immediately reported to the transportation company.
Cable Installation Safety Considerations
Interconnecting, communications, and Class 2 dc power cables should be separated from electrical light
or other Class 1 circuits by at least 2 inches. The exception is where Class 1 wiring or power circuits are
run in a raceway, or are metal-sheathed or metal-clad, or are permanently separated from the conductors
of the other circuitry by a continuous and firmly fixed nonconductor such as porcelain tubes or flexible
tubing in addition to the insulation on the wire. Communications cables and in-building wiring should be
listed and marked for the purpose according to NEC Article 800.
Mounting
Remove the access panel from the Model 234 Stanchion (if applicable).
Remove the back plate from the Paging Module by removing the four #6-32 screws.
The Model 12510-002 or Model 12510-003 Access Panel Kit (sold separately) contains four #6-32 studs
to attach the Paging Module. Attach the mounting plate to the #6-32 studs with the provided #6 keps
nuts. Be sure to note the orientation of the access panel when attaching the plate. Refer to Figure 6 and
Figure 7.
f:\standard ioms - current release\ 42004 instr. manuals\42004-464b.doc
07/14
Page 22
Pub. 42004-464B
Model 10458-701 and 10458-801 VoIP & VoIP WiFi Electronic Paging Modules Page 20 of 24
f:\standard ioms - current release\ 42004 instr. manuals\42004-464b.doc
07/14
Figure 6.
Page 23
Pub. 42004-464B
Model 10458-701 and 10458-801 VoIP & VoIP WiFi Electronic Paging Modules Page 21 of 24
Figure 7. Unit Component Identification
Attach the remainder of the Paging Module to the mounting plate/access panel assembly with the four #632 screws. Note the orientation of the module.
Attach the Access Panel/Paging Module to the Model 234 Stanchion.
f:\standard ioms - current release\ 42004 instr. manuals\42004-464b.doc
07/14
Page 24
Pub. 42004-464B
Model 10458-701 and 10458-801 VoIP & VoIP WiFi Electronic Paging Modules Page 22 of 24
Field Wiring
WARNING
Do not apply power until all the connections have been wired.
After all the field wires are pulled through the stanchion, install all connections as indicated below. Refer
to Figure 8 for wiring details. Refer to Table 4 on page 23 for the recommended conductor sizes and the
termination chart.
N
OTE: Consult the National Electrical Code (NFPA 70), Canadian Standards Association (CSA 22.1),
and local codes for the specific requirements regarding your installation. Install all equipment without
modification and according to the local and national codes. Class 2 circuit wiring must be performed in
accordance with NEC 725.55.
The Paging Module provides terminal blocks on the front of the assembly for all field wiring. Each
terminal block is labeled to indicate functionality. Refer to Figure 8 for sample wiring diagram.
Power Connection
Power over Ethernet (PoE)
The device can be powered from the network cable assuming the speaker output requirement is less than
8 watts. PoE works across standard network cabling (i.e. Cat5) to supply power directly from the data
ports where the device is connected. Connect the LAN cable (Cat5 or Cat5e UTP cable) into the RJ45
connector on the VoIP daughter board. N
OTE: PoE is not applicable to Model 10370-80x series. Refer to
Figure 9.
Local Power
If a speaker output requirement is greater than 8 watts, the device must be powered from a 120 or 240 V
ac power source. Remove the cover from the power terminal block. Connect 120/or 240 V ac power
wires observing the H, N, and END labels. Replace the cover before applying power. N
OTE: External
power supply usage is required for Model 10458-801. Refer to Figure 8.
Speaker Connection
After installing all speaker kits and antenna kit (for WiFi installations), make sure all wires and cables
from the components are at the bottom of the 234 series Stanchion. Connect the black/white and
white/black speaker wires to the 4-point speaker connector.
Speakers 1 and 2 are parallel wired onto terminals labeled 1 and 2. Speakers 3 and 4 are parallel wired
onto terminals labeled 3 and 4. Refer to Figure 8.
Output Contact Connections
Two relay contact sets are available on the chassis. Each contact is Form “A” type normally open (N.O.).
Opto Output Connection
Connect the violet and orange wires from the GAI-Tronics Model 530-001 Strobe Light to the terminals
labeled + and −. Polarity is important: Violet wire (+) and orange wire (−).
f:\standard ioms - current release\ 42004 instr. manuals\42004-464b.doc
07/14
Page 25
Pub. 42004-464B
Model 10458-701 and 10458-801 VoIP & VoIP WiFi Electronic Paging Modules Page 23 of 24
Antenna Connection
For WiFi installations, plug in the BNC connector on the antenna cable into the Paging Module.
Figure 8. Field Wiring Connections
Table 4. Recommended Cabling
Cable Use Recommended Size Conductor Range
LAN Cat5 or Cat5e UTP cable with an RJ45 connector
Power Two-conductor, No. 18 AWG is typical No.28–12 AWG
Speaker Two-conductor twisted pair, No. 18 AWG is typical No. 30–12 AWG
Output contacts Two or three-conductor, No. 18 AWG is typical No. 28–20 AWG
f:\standard ioms - current release\ 42004 instr. manuals\42004-464b.doc
07/14
Page 26
Pub. 42004-464B
Model 10458-701 and 10458-801 VoIP & VoIP WiFi Electronic Paging Modules Page 24 of 24
Figure 9. VoIP PCBA – Component Locations
f:\standard ioms - current release\ 42004 instr. manuals\42004-464b.doc
07/14
Page 27
Warranty
Equipment. GAI-Tronics warrants for a period of one (1) year from the date of shipment, that any
GAI-Tronics equipment supplied hereunder shall be free of defects in material and workmanship, shall
comply with the then-current product specifications and product literature, and if applicable, shall be fit
for the purpose specified in the agreed-upon quotation or proposal document. If (a) Seller’s goods prove
to be defective in workmanship and/or material under normal and proper usage, or unfit for the purpose
specified and agreed upon, and (b) Buyer’s claim is made within the warranty period set forth above,
Buyer may return such goods to GAI-Tronics’ nearest depot repair facility, freight prepaid, at which time
they will be repaired or replaced, at Seller’s option, without charge to Buyer. Repair or replacement shall
be Buyer’s sole and exclusive remedy. The warranty period on any repaired or replacement equipment
shall be the greater of the ninety (90) day repair warranty or one (1) year from the date the original
equipment was shipped. In no event shall GAI-Tronics warranty obligations with respect to equipment
exceed 100% of the total cost of the equipment supplied hereunder. Buyer may also be entitled to the
manufacturer’s warranty on any third-party goods supplied by GAI-Tronics hereunder. The applicability
of any such third-party warranty will be determined by GAI-Tronics.
Services. Any services GAI-Tronics provides hereunder, whether directly or through subcontractors,
shall be performed in accordance with the standard of care with which such services are normally
provided in the industry. If the services fail to meet the applicable industry standard, GAI-Tronics will
re-perform such services at no cost to buyer to correct said deficiency to Company's satisfaction provided
any and all issues are identified prior to the demobilization of the Contractor’s personnel from the work
site. Re-performance of services shall be Buyer’s sole and exclusive remedy, and in no event shall GAITronics warranty obligations with respect to services exceed 100% of the total cost of the services
provided hereunder.
Warranty Periods. Every claim by Buyer alleging a defect in the goods and/or services provided
hereunder shall be deemed waived unless such claim is made in writing within the applicable warranty
periods as set forth above. Provided, however, that if the defect complained of is latent and not
discoverable within the above warranty periods, every claim arising on account of such latent defect shall
be deemed waived unless it is made in writing within a reasonable time after such latent defect is or
should have been discovered by Buyer.
Limitations / Exclusions. The warranties herein shall not apply to, and GAI-Tronics shall not be
responsible for, any damage to the goods or failure of the services supplied hereunder, to the extent
caused by Buyer’s neglect, failure to follow operational and maintenance procedures provided with the
equipment, or the use of technicians not specifically authorized by GAI-Tronics to maintain or service the
equipment. THE WARRANTIES AND REMEDIES CONTAINED HEREIN ARE IN LIEU OF AND
EXCLUDE ALL OTHER WARRANTIES AND REMEDIES, WHETHER EXPRESS OR IMPLIED BY
OPERATION OF LAW OR OTHERWISE, INCLUDING ANY WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Return Policy
If the equipment requires service, contact your Regional Service Center for a return authorization number
(RA#). Equipment should be shipped prepaid to GAI-Tronics with a return authorization number and a
purchase order number. If the equipment is under warranty, repairs or a replacement will be made in
accordance with the warranty policy set forth above. Please include a written explanation of all defects to
assist our technicians in their troubleshooting efforts.
Call 800-492-1212 (inside the USA) or 610-777-1374 (outside the USA) for help identifying the
Regional Service Center closest to you.
(Rev. 10/06)
Loading...