Industrial Radio Remote Controller
SAGA1-P10 Series
User Manual
SSAAFFEETTYY // RREELLIIAABBIILLIITTYY // UUSSEERR--FFRRIIEENNDDLLYY
Gain Electronic Co., Ltd.
www.sagaradio.com.tw
Warning and Caution
The following symbols may be found on the product or throughout the
documentation.
Symbol Description
Refer to Manual
Refer the user manual for additional information when product
marked with this sign.
Dangerous Voltage
Indicates presence of hazardous voltage. Unsafe practice could
result in severe personal injury.
Warning
Denotes a hazard. Included text gives proper procedures.
Failure to follow instructions could result in severe personal
injury and/or property damage.
Caution
Denotes a hazard. Included text gives proper procedures.Failure
to follow instructions could result in minor personal injury and/or
properly damage.
FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
(3) Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
IMPORTANT NOTE
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between radiator & your body.
Industry Canada Notice
Operation is subject to the following two conditions: (1) this device may not cause interference
and (2) this device must accept any interference, including interference that may cause undesired
operation of the device.
Industry Canada Caution
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'IndustrieCanadaapplicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux
conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi,
même si le
brouillage est susceptible d'en compromettre le fonctionnement.
Warranty
Warranty
Gain Electronic Co., Ltd. guarantees that this equipment meets its published
specifications at the time of shipment from the factory. This equipment will perform
as described if installed properly. However, Gain can't guarantee that operation in
SAGA 1 system is absolutely error-free, or without interruption.
Warranty Period
This equipment is warranted against defects in materials and workmanship for a
period of one year from the date of shipment. During the warranty period, Gain is
responsible for necessary repairs as long as the product can be proved to be
defective.
For warranty service or repair, this equipment must be returned to a service facility
designated by Gain. Customer is responsible for shipping charges to Gain, while
Gain will pay return shipping charges.
Excluded Items
This warranty doesn't include consumable parts such as Joystick, batteries, fuses,
buttons and relays. Also this warranty doesn't cover defects caused by improper
installation, improper or insufficient maintenance unauthorized modification,
unavoidable natural essential, improper operation, ignorance of environmental
specifications, improper software/interfacing.
Remarks
1. No other warranty is expressed or implied, except for the above mentioned.
2. The remedies provided herein are the buyers' sole and exclusive
remedies. Gain shall not be liable for any direct/indirect, special, incidental or
consequential damages.
Important Information before You Start
Important
1. Read this manual carefully before operating and installation.
2. Due to the complex nature of equipment, it is necessary to read the entire
manual before installation.
3. Never allow any unauthorized personnel to dismantle equipment as this may
cause the equipment damage.
4. The equipment has been stringently tested for quality assurance before
delivery from factory. However, it must not be used in extremely dangerous
situations, or where damage may result.
5. After operation, switch off crane main power as well as receiver unit and
remove rotary key from transmitter unit.
6. The transmitter should keep in a safe place when not in use to avoid any
unintentionally operation.
7. The crane should be equipped with main power relay, limit switch and other
safety devices required.
8. Do not use this device during electrical storm or where there are conditions of
high electrical interference.
9. Always check transmitter battery and receiver input power condition before
operation.
10. The installation and maintenance service is allowed only when the crane and
receiver power are off to avoid electrical shock.
11. The contents of the manual may be amended by the manufacturer without
notice.
12. The specification and function is subjected to change without notice by
manufacturer.
Precautions
1. Press EMS button and switch off main power of crane and receiver after
operation. Then remove transmitter rotary key and keep in a safe place.
2. The following situations may cause receiver response delay and stop operation
immediately when situation occurs.
(a) Beyond operating range
(b) During severe radio interference
3. Remove transmitter batteries when not in use for long period of time.
4. To extend product life, please follow the standard operating procedure and
maintain system regularly.
5. Check EMS button and other system main functions before operation.
6. Press EMS button during system failure or any abnormal conditions occur.
7. The operator must be familiar with emergency procedures before operate the
system.
Emergency Procedures
In case of emergency, please follow the procedure below:
1. Press EMS button and stop operation.
2. Switch rotary key switch to "OFF" position and remove it from transmitter unit.
3. Switch off crane main power.
4. Contact the authorized distributor for further assistant.
□2 □3
Transmitter Overview
SAGA1-P10 Transmitter Overview
□1
□3
□5
□1 EMS Button □2 LED Indicator
□3 Function Button □4 Rotary Key Switch
□5 Battery Cover
General Operation
□4
Getting Started
1. Install 4 new AA-size batteries in the battery compartment (make sure batteries
correctly installed according to the indication of “Positive” & “Negative”) and
close battery cover firmly.
2. Insert rotary key switch into transmitter unit and switch to “ON” position.
3. Switch rotary key switch from “ON” to “START” position to power on the system.
Note: Red LED indicator will flash when fail to follow procedures above
accordingly.
4. Press function button for operation.
Follow the procedures below when finish operation
1. Press EMS button
2. Switch rotary key switch to “OFF” position
3. Remove rotary key and keep in a safe place
4. Remove batteries if not to be used for long period of time.
Transmitter LED Indicator
Green (Full Power) Operate as usual.
Yellow (Mid Power) Unload the article as soon as possible and stop operation until
new batteries are replaced.
Red (Low Power) An EMS signal will be sent to receiver automatically to turn off
receiver. To avoid the interruption during operation, check
battery power frequently.
Note: Switch rotary key switch to “OFF” position to turn off transmitter
completely thus extend battery life, otherwise transmitter is in standby
mode when rotary key switch remain in “ON” position.
Changing Receiver Input Voltage
If the factory preset receiver voltage is different from application, follow the
procedures below to change input voltage.
1. Switch off receiver main power.
2. Remove the connector from original position.
3. Insert connector to new voltage position accordingly.
Troubleshooting
A. When transmitter red LED flash fast continually, it may be
1. One of pushbutton jammed.
2. EMS button is not disengage
3. Fail to follow Power-on procedures accordingly.
B. When transmitter red LED flash slowly, it may be low battery power.
Loading...