Gain Electronic Co 081K User Manual
Installation & Operation Manual
SAGA1-K Series Industrial Radio Remote Control
Gain Electronic Co. Ltd.
Table Of Contents
Safety Considerations ------------------------------------------------------------2
Part. 1 Operator’s Manual
Chapter 1 Warranty -----------------------------------------------------3
Chapter 2 Precautions of Operation --------------------------------- 4
Chapter 3 Standard Accessories ---------------------------------------6
Chapter 4 Operation -----------------------------------------------------7
Chapter 5 Inspection and Fault Detection ---------------------------10
Chapter 6 FAQ ----------------------------------------------------------11
Part. 2 Technician’s Manual
Chapter 1 General Characteristics -------------------------------------12
Chapter 2 System Configuration ---------------------------------------13
Chapter 3 Installation ----------------------------------------------------15
1
Safety Considerations
Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
This product and related documentation must be reviewed for familiarization with
safety markings and instructions before operation.
Safety Symbols The following symbols may be found on the remote control
or throughout the remote control’s documentation.
Refer to Manual
When product is marked with this symbol refer to instruction
manual for additional information.
High Voltage
Indicates presence of hazardous voltage. Unsafe practice
could result in severe personal injury.
Warning
Denotes a hazard. Included text gives proper procedures.
Failure to follow instructions could result in severe personal
injury and/or property damage.
Caution
Denotes a hazard. Included text gives proper procedures.
Failure to follow instructions could result in minor personal
injury and/or properly damage.
2
Part 1. Operator’s Manual
Chapter 1 Warranty
1-1 Warranty
Gain Electronic Co., Ltd. guarantees that this product meets its published
specifications at the time of shipment from the factory. Under proper installation
it should work as expected.
1-2 Warranty Period
This equipment is warranted against defects in material and manufacturing for a
period of one year from the date of shipment. During the warranty period, Gain is
responsible for necessary repairs as long as the product can be proved to be
defective.
For warranty service or repair this product must be returned to a service facility
designated by Gain. Buyer will pay shipping charges to Gain while Gain will pay
return shipping charges.
1-3 Excluded Items
This warranty does not include consumptive parts such as batteries, fuses, buttons,
and relays. Also this warranty does not cover defects caused by improper
installation, improper or insufficient maintenance, unauthorized modification,
improper operation, ignorance of environmental specifications, or improper
software or interfacing.
1-4 Remarks
No other warranty is expressed or implied, except for the above mentioned.
The remedies provided herein are the buyer’s sole and exclusive remedies.
Gain shall not be liable for any direct, indirect, special, incidental or
consequential damages.
3
According to FCC Part 15.21 Information to user.
Caution :
The user that changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
Chapter 2 Precautions of Operation
2-1 Attention
Please carefully read the manual before installing and operating this device.
Due to the complex nature of this equipment it is necessary to read the entire
manual before installation.
Never dismantle the equipment by any unauthorized personnel, or equipment may
be damaged.
This manual is for reference only. Pleases consult your distributor for further
assistance.
The equipment has been strictly tested for quality before delivery from our plant.
However, this equipment must not be used in dangerous situations or where
damage may result.
After operation, shut off main power to the crane, power to receiver, and remove
transmitter key.
Transmitter should be placed in a safe area when not in use to avoid accidental
pressing of buttons.
The crane should be equipped with main power relay, limit switch and other safety
devices.
Don’t use equipment during lightening or high electrical interference conditions.
Make sure that the batteries are in good condition and power for receiver is correct.
Maintenance should only be done while the crane’s main power is off to prevent
electrical shock.
The contents of this manual may be amended by the manufacturer without notice.
The manufacturer may introduce new functions to the equipment as necessary,
therefore, the descriptions may change.
4
2-2 Precautions
Operating in an industrial facility is relatively dangerous; therefore, operator must
have taken the adequate trainings in using SAGA1-K system.
Those who operate the machine should be healthy and have good judgment in
regard to safety.
Although the SAGA1-K transmitter is so durable and resistant for the fluctuating
temperature, care still need be taken to prevent it from the severe impact or
pressure.
During operation, if the power supply of the transmitter’s batteries is insufficient,
the transmitter will send out EMS signal first to de-energize all of motion relays
inside the receiver to stop crane’s moving, and then the LED indicator on
transmitter will flash in red constantly. At this moment, the batteries need to be
replaced and all of four batteries should be replaced at the same time.
If the severe interference occurred the equipment should be stopped at once.
Please take the batteries out when the equipment will not be used for a long time.
Be sure to know the “Procedures of Emergency “ as follows.
2-3 Procedures of emergency
In case of an Emergency, please follow the steps below and ask the distributor for
service immediately.
1. Press "EMS" button.
2. Turn the key to "OFF" position and remove it.
3. Switch off the main power of crane.
4. Advise the distributor to find out the reason.
5
Loading...