
VG 415 211CA
Stainless steel
Width 15" (38 cm)
Natural gas. For conversion to
LP gas, LP kit (part #10004445) must
be ordered.
Included accessory
1 wok attachment ring
Installation accessories
In combination of several Vario
cooktops or VL 414 downdraft,
connecting strips must be used.
Choose respective VA 420 strip from
one of the below, depending on type
of installation.
VA 420 000
Connection strip for combination
with other Vario 400 series appliances
for flush mounting.
VA 420 010
Connection strip for combination
with other Vario 400 series appliances
for surface mounting.
VA 440 010
Stainless steel appliance cover with
mounting strip.
Only available for individual Vario
installation.
Optional accessories
WP 400 001
Wok pan made of multiple-layer
material with round bottom and handle
ø 14 ³⁄₁₆", 6.3 qt., height 4".
AA 414 010
Stainless steel, removable air deflector
for gas Vario next to VL 414 downdraft.
Combinable with:
2 x VL414712
AL400721
AI442720 / AI442760
AW442720 / AW442760
AF210791
Good to know:
Wall installations require the hood to
be as large as the cooktop(s). Island
installations require the hood to be
larger than the cooktop(s).
Important note:
If paired with VL414712, for best
performance it's recommended to
place a VL on each side of the gas wok.
Vario 400 series gas wok
VG 415
– Three-ring burner with 18,800 BTU
– Full electronic power regulation on
12 levels.
– Precise and reproducible flame
regulation
– Automatic ignition, electronic flame
monitoring with automatic
re-ignition
– Simmer function for cooking on a
very low output level
– Solid stainless steel control knob
– Precision-crafted 3 mm stainless
steel
– For surface mounting with a visible
edge or for flush mounting
– Can be combined with other Vario
400 series products
Cooking zones
1 multi-ring wok burner (300 W –
5,500 W), 1,000 – 18,800 BTU,
suitable for pots up to max. ø 12 ⅝".
Operation
Control knobs with illuminated
ring, cooking zone and output level
markings.
One-handed operation.
Full electronic control in 12 output
levels for exact power level regulation
plus simmer function.
Automatic ignition.
Features
Simmer function.
Cast-iron pan support with flat,
continuous pot surface.
Brass burner rings.
Equipped for natural gas. For
conversion to LP gas, LP kit (part
#10004445) must be ordered.
Safety
Electronic flame monitoring with
automatic re-ignition.
Residual heat indication.
Safety shut-off.
Planning notes
If using the VL414 downdraft for
ventilation, the Vario gas wok must be
placed between two VL downdrafts.
Recirculation is not recommended.
Depending on the type of installation
(surface-mounted or flush-mounted,
with or without an appliance cover),
the specific location of the cut-out and
the knob positions may vary.
The drawing "Installation of the control
knob" must be observed if the panel is
more than 1" thick (there must be a
recess at the rear).
If combining several Vario 400 series
appliances, a connection strip
VA 420 must be placed between the
appliances. Depending on the type of
installation, the corresponding
connection strip must be provided.
The weight bearing capacity and
stability, in the case of thin countertops in particular, must be supported
using suitable substructures. Take into
account the appliance weight and
additional loads.
Additional instructions for flush mounting:
Installation is possible in countertops
made of stone, synthetics or solid wood.
Heat resistant and watertight sealing of
the cut edges must be observed.
For a suitable heat resistant filler please
consult the countertop manufacturer.
The groove must be continuous and
even, so that uniform placing of the
appliance on the gasket is ensured.
Do not use discontinuous lining.
The joint width may vary due to size
tolerances of the combinations and of
the countertop cut-out.
If installing several appliances in
individual cut-outs allow for a minimum
distance of 2" between the cooktops.
Plan for an electrical connection
(the appliance is not operable without
power supply).
Air intake from above.
No intermediate shelf required.
Rear panel and wall trims must be
heat-resistant and consist of a
non-flammable material.
A minimum clearance of at least 6"
from adjacent heat-sensitive cabinets
or contact surfaces must be observed
or thermal insulation fitted.
If operated next to the downdraft
ventilation VL 414, the air deflector
AA 414 010 is recommended to ensure
maximum performance of the cooktop.
With a total connected load of more
than 37,533 BTU local regulations
concerning room ventilation, room size
and combination of extraction or
recirculation hoods must be observed.
Minimum clearance between gas cooktop(s) with more than 37,533 BTU and
ventilation hood must be 30".
Appliance can be snapped into the
countertop from above.
Appliance weight: approx. 33 lbs.
Rating
Rating: 25 W (18,800 BTU)
Minimum fuse protection: 15 A
Electrical: 120 V / 60 Hz
Electrical connection:
Plan for a 55" long connecting cable
with 3 prong NEMA 5-15 plug.
www.gaggenau.com/us
Revised: June 2021

Surface-mount Installation Flush-mount Installation
Installation of the control knob; surface mounting
> ⅞" (23)
14¹⁵⁄16"
≥ 1¹⁵⁄
(50)
⅛" (3)
5³⁄
" (131)
16
(1400)
16
"
> 1⅜"
(380)
55"
(35)
14³⁄16"
(360 )
20½"
(520) (A)
±1
Installation of the control knob
±¹⁄
16
"
±¹⁄
19⅜"
±1
(492 ) (A)
16
"
ø 1¹⁵⁄
(50)
ø 2⅜"
(60)
14¹⁵⁄16"
(380)
5¼" (134)
55"
(1400)
16
"
16
"
R ⅛" (R 3)
90°
≥ 1¹⁵⁄
(50)
> 1⅜"
(35)
14³⁄16"
(360 )
15⅛"
(384+1)
20½"
(520) (A)
"
16
±¹⁄
±1
+¹⁄16"
⅛" (3)
±¹⁄
19⅜"
±1
(492 ) (A)
ø 1¹⁵⁄
16
(50)
ø 2⅜"
(60)
16
"
"
+¹⁄16"
20⅝"
(524+1) (A)
R ³⁄
+¹⁄16"
16
"
(R 4+1)
(B)
90°
R ⅛" (R 3)
Longitudinal section
Gas connection
> 1⅜" (35) > 1⅜" (35)
1⅜" (35)
16
" (50) ø 1¹⁵⁄16" (50)
ø 1¹⁵⁄
2¾" (70)
≤ ⅞" (23)
1
/2"*
1
(38*)
4
(107)
3
/16"
⅞" (23)
¹⁄16"
(2)
Cross-section
16
"
¹⁄
(2)
(380)
14³⁄
(360 )
15⅛"
(384+1)
19⅜"
20⅝"
16
±¹⁄
16
"
±1
+¹⁄16"
(520)
(492 )
(524+1)
16
±¹⁄
±1
+¹⁄16"
¹⁄16"
(2)
(A)
"
(B)
¹⁄16"
(2)
(A)
16
"
* 21/16" (53 mm) with appliance cover or adjustment strip.
Numbers indicated
inside parenthesis ( ) = mm
1/
2"
www.gaggenau.com/us
Revised: June 2021