Gaggenau DF270800 Quick reference guide

Before using forthefirst time, read theoperating instructions.

1

2

max

15 ml

25 ml

50 ml

en

Setting up Home Connect

Tip:Connect your appliance to a mobile device. You can con-

veniently change all settings via the HomeConnect app.

1.

Install the HomeConnect app on your mo­bile device and follow the instructions.

2.

Scan the QR code using the HomeCon­nect app.

Quick reference guide  Dishwasher

Overview of water hardness settings

You can find an overview of the
water hardness values that can
be selected here.
A table of country-specific units
can be found in the instruction
manual.

Hardness
range

mmol/l Setting

value

Soft 0 - 1.1 0 - 8
Soft 1.2 - 1.4 9 - 10

Medium 1.5 - 1.8 11 - 12
Medium 1.9 - 2.1 13 - 15
Medium 2.2 - 2.9 16 - 20
Hard 3.0 - 3.7 21 - 26
Hard 3.8 - 5.4 27 - 38
Hard 5.5 - 8.9 39 - 62

Adding special salt

To avoid damage to the appliance, only add special
salt to the dispenser for special salt just before the
programme starts.

1.

Unscrew the lid of the dispenser for special salt
and remove.

2.

On initial start-up: Fill the dispenser right up with
water.

Adding rinse aid

1.

Press the catch on the lid
of the dispenser for rinse
aid and lift ⁠.

Setting the water softening sys­tem

1.

Press ⁠.

2.

To open the basic settings, press
for approx. 3seconds.

3.

Press repeatedly until the display
shows "Water hardness".

4.

Press or repeatedly until the
right water hardness has been set.

5.

To save the settings, press for ap­prox. 3seconds.

3.

Add the special salt to the
dispenser. The water in the
dispenser is displaced and
forced out. Never add de­tergent.

4.

Place the lid back on the dispenser and turn to
close.

2.

Add rinse aid up to the
max mark.

3.

Close the lid of the dispenser for rinse aid.

a The lid clicks into position.

Technical data

The specified values are laboratory
measurements taken in accordance
with GB38383, ECO program.

Grade 1
Power consumption

[kW•h/cycle]
Water consumption

[L/cycle]
Cleaning index 1.12
Drying index 1.08

1

Noise
[dB (A)]

Energy efficiency index 45
Water efficiency index 43
Place settings 13
Sterilization rate

1

Basis for test: GB/T 4214.3

2

Basis for test: QB/T 5133

The sterilization function meets the
relevant requirements of QB/T 1520
during the life cycle.
Types of bacteria removed: Escheri­chia coli, Staphylococcus aureus.

Instruction for test institutes

Test institutes receive the information
for comparability tests (e.g. loading,
detergent, noise measurement setup
etc.).
Request by e-mail to:
[e-mail]
The product number (E no.) and the
production number (FD) are required
which you can find on the rating plate
of appliance inner door.

0,740

10,0

44

2

99.99%

How to use your appliance

1.

Load the tableware.
Only clean tableware that is suitable for dish­washers. Remove large remnants of food from
the tableware. Check that the spray arms can ro-

9001620332 (010326) DF270800

*9001620332*

Adding detergent

1.

Add the detergent to the
dry detergent dispenser.

tate freely.

2.

Add detergent.

3.

Switch on the appliance ⁠.

2.

Close the lid of the deter­gent dispenser.

a The lid clicks into position.

4.

Select the programme.

5.

Start the programme ⁠.

6.

Remove the tableware at the end of the pro­gramme.

7.

To cancel the programme, press for
approx. 4seconds.
The programme is cancelled and ends after ap­prox. 1minute.

Cleaning filters

1

2

1

2

1

2

1

2

1.

After each wash check the filters for
residue.

2.

Turn the coarse
filter anticlock­wise and re­move the filter
system ⁠.

3.

Pull down the mi­cro filter to re­move.

Troubleshooting

Fault Cause and troubleshooting

E:3200 or indicator for
water supply lights up.

Supply hose is kinked.

▶

Install the supply hose without kinks.

Water tap is turned off.

▶

Turn on the water tap.

Water tap is jammed or furred up.

▶

Turn on the water tap.
The flow rate must be at least 10 l/min when the water sup­ply is open.

The filters in the water connection of the supply or AquaStop
hose are blocked.

1.

Switch off the appliance.

2.

Pull out the mains plug.

3.

Turn off the water tap.

4.

Unscrew the water connection.

5.

Remove the filter from the sup­ply hose

6.

Clean the filter.

7.

Re-insert the filter in the supply hose.

8.

Screw the water connection back on.

9.

Check the water connection for leaks.

10.

Restore the power supply.

11.

Switch the appliance on.

4.

Press the locking
catches to­gether and lift
the coarse filter
out ⁠.

5.

Clean the filter elements under running
water.

6.

Re-assemble the filter system.

7.

Insert the filter system into the appliance
and turn the coarse filter clockwise.
Make sure that the arrow markings
match up.

Fault Cause and troubleshooting

E:9240 lights up. Filters are soiled or blocked.

E:6102 lights up. Wastewater pump is blocked.

Remnants of food on
tableware.

Cleaning spray arms

1.

Unscrew the upper spray arm and
pull down to remove ⁠.

2.

Pull up the lower spray arm to remove.

3.

Check the outlet nozzles on the spray arms for blockages un­der running water and remove any foreign bodies.

4.

Insert the lower spray arm.

a The spray arm clicks into position.

5.

Insert the upper spray arm and screw it firmly in place.

▶

Clean the filters.

▶

Clean the wastewater pump.

Cover of the wastewater pump is loose

▶

Secure the cover of the Wastewater pump so it clicks into
position.

Tableware is placed too close together or basket is overfilled.

1.

Arrange tableware with sufficient space in between.
The spray jets must reach the surfaces of the tableware.

2.

Avoid points of contact.

Spray arm rotation is blocked.

▶

Arrange tableware so that it does not obstruct spray arm ro­tation.

Spray arm nozzles are blocked.

▶

Clean the Spray arms.

Filters are soiled.

▶

Clean the filters.

Filters are inserted incorrectly and/or not engaged.

1.

Insert the filters properly.

2.

Engage the filters.

Washing programme selected too weak.

▶

Select a more intensive washing programme.

▶

Adjust the sensitivity of the sensors.

Clean wastewater pump

1.

Disconnect the appliance from the power supply.

2.

Remove the filter system.

3.

Scoop out any water.

4.

Prise off the pump cover using a
spoon and grip it by the crosspiece.

5.

Lift the pump cover inwards at an angle and remove.

6.

Remove any remnants of food and foreign bodies in the area
of the impeller.

7.

Insert the pump cover and press
down ⁠.

a The pump cover clicks into position.

8.

Install the filter system.

Fault Cause and troubleshooting

Removable streaks are
present on glasses, glass­ware with a metallic ap­pearance and cutlery.

Rust spots on cutlery. Cutlery is not sufficiently rust-resistant. Knife blades are often

Detergent residue is
present in the detergent
dispenser or the tablet
collecting tray.

Amount of rinse aid to be dispensed is set too high.

▶

Set the rinse aid system to a lower setting.

No rinse aid has been added.

▶

Add rinse aid.

more severely affected.

▶

Use rust-resistant tableware.

Cutlery may also rust if washed together with rusting items.

▶

Do not wash rusting items.

Spray arms were blocked by tableware so detergent was not
rinsed out.

▶

Check that the spray arms are not blocked and can rotate
freely.