Digital Alarm Clock HD SPY DVR
(Motion Activated with Remote)
Instruction for Use
Table of Contents
Preface and Quality Assurance
Using instruction for Chinese time signal clock
DV Structure diagram
DV product introduction & handling instruct ion
DV File storage instruction
Relevant parameters of DV
Power source and fittings
Troubleshooting
Precautions
Preface
This Instruction will guide you how to use the product. Meanwhile it provides the
necessary information related to the product, such as the information for operating
and handling. You are recommended to read the Instruction carefully and understand
all contents herein before operating. Please keep the Instruction carefully. We hope
this product satisfied with your demand and sever you better.
Product Assurance
This product is with FCC and CE certificate and had inspected by the authorized
organizations where was found to comply with the recommended indexes. User is
under our safety assurance when operating this product.
Instruction for Use for Time-signal Clock
I. Basic functions
1. 5 buttons: HR, MIN, SET, LIGHT, TALK/SNZ;
2. The time & minute can be displayed in a 3. 5 bit LCD panel. Time-showing system of
12 hours and 24 hours is available;
3. Multiple rings for choice: Beep, cock, etc. 5 melodies for option.
4. The time alarm will be triggered every 10 minutes if the clock is on the snooze
function. It can alarm 6 times maximally.
5. Two on-the-hour alarm functions for choice;
6. The ring of “Beep” will be become louder generally. And it will last 1 minute;
7. If adopting the melody as the ring, the clock will alarm when the melody ends.
II. Function operation
1. When switching the power on, the whole LCD will display; after the ring of a melody
ends, the clock will display time;
2. P ress “Set” button under the Time mode to set as per the following sequences (the
display will flash simultaneously):
Time setting → Alarm setting → On-the-hour alarm setting
3. Press “HR” button under the Time Setting mode to set hour and “MIN” button to set
minute;
4. Press “HR” button under the Alarm Setting mode (Symbol:
) to set hour and
“MIN” button to set minute. Press “SNZ” button when alarming, the clock will re-alarm
every 10 minutes, and will send alarm by 6 times at mos t;
5. Under the On-the-hour Alarm Setting mode (the symbol of alarm and the on-the-hour
alarm will flash):
It will open and close the function (Symbol:
) by pressing the “HR” button, but send
alarm during the time from 7:00am to 9: 00pm (Symbol: ); it can activate the inactivate
the alarm ring by pressing “MIN” button (Symbol:
).
6. Under the Time Mode and if the “HR” button is pressed, it c an shift the hour system
(12/24 hour system); by pressing “MIN” button, it can select the alarm ring.
7. Under any modes, it can turn the background light off by pressing the “LIGHT” button.
8. Under any modes, it can report the time by pressing the “TALK” button.
DV Using Instruction
I. Structure Diagram
Ti
II. Product Introduction
This product is a high-resolution 30-frame (640X480, 1280*960) remote v ideo surveillanc e clock, with an
external TF Card. As a multi functional high-tec h product, the product is availabl e multi ple functi ons, suc h
as: video, sound recording, induction video, take a photo, cyber chat, electric alarm clock and file storage;
with the high-capacity battery, it can last recording for about 12 hours continuously and audio recording for
25 hours continuously; besides, the product can replace the high-resolut ion video with 2 million pixels,
sound and file automatically, Meanwhile, the product is designed th e multiple languages for telling the
time. It supports 32GB storage. Its TF card can be used for a long time and remote controller can be easy
to handle. With the best imperceptibility, this product will be as your ideal assistant to prevent theft and get
evidence.
1、Alarm Clock
Time-telling button
Rotational cover
TF card
Turn off
Turn on
Electric Clock Function Button
Receiver
2、Remote controller
Sender
Switch button
Video
motion detection video
Sound recording
Take a photo
III. Handling Instructions
1. Open the rotational cover at the right side, insert the TF card and turn “ON” to get ready.
2. Use the remote controller to aim to the receiver of the clock and press "
" to start. When the blue lamp
is on and the clock is under the stand by mode.
3. Press
to start recording video. After the blue lamp flashes 3 times and then turns off, it start recording.
stop pressing
, it will save the video file and return to the “holding state” , and the blue lamp will be on
(the default time length for video recorded is 20 minutes).
4. Press button to start recording a sound; after the blue lamp flashes 3 times and turns off, it will be put
into the working order; Press again, it will save the sound file and return to the “holding state” , and
the blue lamp will be on (the default time length for sound recorded is 20 minutes);
5. Press button to get in photo taking mode. It will take a photo if pressing this button again. When
pressing this button, the blue lamp will flash; after taking the photo, it will return to the stand by.
6. Press
button to get in motion detection mode, then the blue lamp will flash quickly. If a moving object
is detected, the blue lamp will flash slowly by two times and the device will be start to record video. If there
is no moving object to be detec ted, the blue lamp will return to “Quick-flash: and get in motion detection
mode (the default length for the video file is 3 minutes);
7. Press
button, it will turn t he device off and the blue lamp will be off.
8. When the switch is “ON”, insert the U SB cable and then press
button on the remote control ler, the
device will access to the U-disc mode.
9. PC camera function: Please install the driver software which is saved in the Compact Disc before
operating; Turn on the device by pressing
on the remote controller when the device is under the mode
of “ON”, insert USB cable to connect the computer; at t hi s time, it will access to PC CAM mode;
10. Charging: Place the chief switch to “OFF” position, insert USB adapter, and the red lamp will be on; When
it is full, the red l amp will be off. You can charge it too by connect this device to a comput er ( Please
use only the adapter provided with the device together; if the device getting hot or occurs other
unexpected situations whilst charging, please disconnect the adapter' s power source);
11. Reset: If the product s tops working under ill egal operation or other unclear reasons, please place the
switch of the device to “OFF” position, and then to “ON” position. It will reset the product accordingly;
12. When the battery is low capacity, the blue lamp will keep flashing or the screen display will be unclear.
Then please charge it immediately. If it is used off, the file wil l be saved automatically;
13. Recorder date: Run the writertime file( in CD disc) when the camera connect with computer. And then ,the
video time is the same computer.
14. File updat e: please install “Network Installer” from the installation disc; use the remote c ontroller to ope n
the clock, and then insert the USB cable in 10 seconds; afterwards, t he computer will open an interface
automatically; click “Program Upgrade”, it will open a dialogue box; afterwards click “Update”.
When ① DRAM Timing, select 0X35
When ② DRAM Size, select “8M”; afterwards, pres s “OK” to upgrade; several minutes later, press
“Confirm” button.
15. When the prog ram is lost, please install the software which is saved in the Compact Disc, and then click
“STK02NU Programme Upgrading Tool”, afterwards click “Update”;
Under ① DR AM Timin g , select 0X3 5
Under ② DRAM Size, select “8M”; afterwards, press “OK” to upgrade; several minutes later, press
“Confirm” button.
IV. File’s storage and play
When finishing video-recording and other operations, please place the switch to “ON”
position, connect it to your computer by USB cable, and press
on the remote
controller; copy the file or cut and paste it to the your computer to play; or you can remove
the TF card and use the card reader to read t he data inside.
The Media player / KM player is recommended.
V. Precautions
Application conditions: Please abide by the related national laws and regulations strictly; it is prohibited to
use the product for illegal purpose, otherwise you must be responsible for the consequences.
Software upgrade: In order to keep the devic e available a better performance, the manufacturer shall
improve the product software continuously. The device is designed the functio n to update by user itself,
please claim the latest software and upgrading method towards your local deal er.
Working temperature: Please use the de vice onl y at the natural tem perat ure; never use the d evice at the
temperature that human body feels unconformable.
Working humidity: Please use the device only in th e environmental humidity suitable for living; keep the
device faraway from the wet environment . This device is not designed the water-proof function.
Video luminance: Please use the device when the sufficient luminance is avai lable; it i s prohibite d to use
the lens to aim to the sun or other intensive light source; otherwise it may damag e the optical apparatus;
Cleanliness requirement: Please do not us e the device in the environment full of dirt; otherwise it may
cause the lens or other parts to attach with dirt and influence video effect. It can use the lens wiping paper
or glass cloth to clean.
Other precautions:
This device is a precision electronic product; please keep it away intensive impact, shock, intense
magnetic field or electric field.
USB data cable
USB port of
computer
V. Relevant Parameters
Pixel
2.0 maga pixel
Resolution
640*480、1280*960
Video format
AVI
Frame number
30fps
Vision angle
72°
Induction photographing
6 meters for Straight-line distance
Minimal illumination
1LUX
Battery capacity
2200MA
Continuous recording time
Over 12 hours
Remote operating distance
15m
Scope for sound recording
40m2
Power consumption
130MA / 3.7V
Storage temperature
-20~80℃
working temperature
-10~60℃
working humidity
15~85% RH
Type of memory card
Mini SD card
Capacity of memory card
32GB maximally
Player software
Media player / KM player
USB Interface
USB1.1/2.0
Operating system
WIN 2000/ XP / Visat32 / 7
Time consumed of storage
1GB/40 minutes
Charging time
About 4 hours
Troubleshooting
Trouble
Troubleshooting
Can not turn on
Remove the insulator
lock of Power, please charge accordingly;
Battery is not contact well, re-start
Can not charge the electricity
Replace the battery or adapter
Blue light flashes rapidly re-start camera, low-
power charging
reminder, delete redundant files from the
card, put in TF Card or replacing TF Card.
Remote controller is hard to use
Align with the receiver’s head, remove the
insulator of remote controller, replace
battery or wait for reading the card
Cannot connect with computer
Replace the data cable or computer
Clock’s screen flashes or character is
displayed incompletely
Charging
Sound is recorded with noise or video is not
clear
Charging, replace TF card
Other problems
Please contact local seller
Power Source
This product can only be allowed to comply the authorized power sources with the
following marks, i.e.:
UL mark / American Power Certification
CE mark / UN Power Certification
CCC mark / Chinese Power Certification
BS mark / British Power Certification
C-TICK mark / Australian Power Certificat i on
GS mark / German Power Certification
PSE mark / Japanese Power Certific ati on
Note:
The power device will get a rising-temperature on the surface when operat ing. This is an
expected phenomenon. If it is a must to bring the power device with you, please remove it
from the power socket.
Necessary Fittings
Compact Disc Switching power supply
USB Data Cable Instruction For Use
Loading...