Page 1
Before connecting the unit for the first time, please, read
these instructions carefully.
1.- IMPORTANT INFORMATION
• The warranty of the panel heater will not cover any damage
• This Guide must be kept and given to any new owner.
• Check that the voltage shown on the rating plate on the heater is
• Should the heater be moved and reinstalled it is essential that the
• The use of panel heaters is forbidden in any area where there is a
• Do not use this heater to dry clothes.
• Neither the connecting cable nor any other object must come into
• Do not cover this heater at any time.
• The surfaces of this heater can be hot, so young children should
• The air outlet grill at the top of the heater cabinet and the air inlet
• This heater should be disconnected from the electricity supply
• The panel heater should not be installed just below an electrical
• The appliance must be installed in such a way that switches and
• The installation must be carried out in accordance with the current
• The heater is fitted with a flexible cable size 3 x 1.00 mm2 for
• This appliance must be connected to the supply by fixed wiring.
• If the flexible power cable for this unit is damaged, it may only be
• This appliance must be earthed.
• Before carrying out any work inside the appliance, the panel heater
• The presence in the air of particles of smoke, dust and other
• Please complete the enclosed warranty card and return it to the
• All models are supplied with an electrical interrupt cut-out. This will
PHM200 RATING 2000 W 230 – 240 V~
caused by non observance of any of these instructions.
the same as the voltage of the supply to which connection is to be
made.
work is carried out by a competent electrician.
presence of gases, explosives or inflammable objects.
contact with the hot unit.
not be left unsupervised in the vicinity of the heater.
at the bottom of the heater are provided to ensure the most effi-
cient operation of the appliance. They also protect the heater from
overheating, therefore, it is essential that at no time are they covered.
before any repair work is carried out. This action should also be
taken during the times of the year when heat is not required.
socket.
other control devices cannot be touched by a person using a bath
or shower.
electrical regulations.
electrical connection. It may be used to connect the heater to the
fixed wiring of the premised through a suitable connection box positioned adjacent to the panel heater.
The supply circuit to the heater must incorporate a double pole
isolating switch having a contact separation of at least 3 mm.
replaced by a repair workshop recognised by the manufacturer, as
special tools are necessary.
must be disconnected from the electricity supply.
pollutants could, in time, discolour the walls and surfaces around
the panel heater.
manufacturer to enable registration to take place.
switch off the heater if, for any reason, it overheats. Should the cut-
out operate, turn the heater off and remove the cause for the overheating. The cut-out will be reset automatically.
PANEL CONVECTOR HEATERS
INSTALLATION INSTRUCTIONS AND USER GUIDE
PHM075 RATING 750 W 230 – 240 V~
PHM125 RATING 1250 W 230 – 240 V~
PHM150 RATING 1500 W 230 – 240 V~
2.- Installation instructions
- When positioning the heater for installation it is important that a minimum clearance of 50 cm must be allowed between the heater and any
combustible materials, such as furniture, curtains etc, to ensure the best
heating results.
- Open the carton at the indicated side. The screws are in the accessories
bag. Turn the carton upside down to allow the heater to stand. Check that
it is the correct model and that it is in good condition.
- Fix the two square brackets to the back of the heater by using the two
small screws (see Fig. 1).
min 20cm min 20cm
- Position and fix the top bracket at the correct distance from the floor
(see Fig. 2) and hang the unit on the hooks of the top bracket. Mark the
fixing points on the wall using a pencil. Use the heater fixing holes as a
template and mark the wall through the two fixing holes in the square
brackets. Fix the heater to the wall.
8cm
10cm
Fig. 1
41.0 cm ( 750W)
56.0 cm (1250W)
63.5 cm (1500W)
78.5 cm (2000W)
Fig. 2
min 15cm min 15cm
41.0 cm
Page 2
3.- Using the panel heater.
7
6
5
4
9
8
10
*
2
3
3.- Cleaning and maintenance.
Clean and dust with a dry, soft cloth only when the unit is disconnected and cold.
Do not use solvents or abrasive products for cleaning.
Switch on the heater by setting the switch marked I-O to “ I “. The off position is
marked “ O “.
When the heater is generating heat the neon indicator on the switch will be illuminated.
The heater is fitted with an adjustable thermostat, which enables room temperature to
be controlled by adjusting the setting accordingly. Turn the thermostat control to the
maximum (fully clockwise) to heat the room rapidly. When the desired temperature has
been reached, turn the thermostat control slowly to the left (anti-clockwise) until the
luminous indicator switches off. By leaving in this position, the heater will automatically
maintain the selected temperature.
4.- Wiring
R: heating element with safety cut out
C: Switch
Ta: Ambient thermostat
Brown : Live
Blue : Neutral
Green and Yellow : Earth
The symbol on the product or in its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to
the applicable collection point for the recycling of electrical and electronic
equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health,
which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop
where you purchased the product. These instructions are only valid in the EU
member states.
Made by ELNUR s.a.
Pol. Ind. “El Nogal” c/ Villa Esther, 11
www.elnur.es
As a part of the policy of continuous product improvement Elnur s.a reserves the right to alter specifications without notice.
@ 2008 Cod. 40490017-A
Loading...