Page 1
TM
E-VentTM System
INSTALLATION INSTRUCTIONS
Page 1 of 1
You may wish to paint your E-Vent™ system prior to installation. This can speed up installation and reduce errors.
Materials needed:
• Safety glasses
• Tape measure
• Hammer or Pneumatic Nailer
• Nail Countersink
• Corrosion-Resistant Fasteners
• Caulk Gun
• Polyurethane Compatible Adhesive
1. Draw a Layout of the Roof-line
Begin by drawing a simple layout of the roof-line. Determine the location and quantities of the parts you need.
2. Apply Adhesive and Set Corner Into Place
Starting with one of the corners, apply a bead of adhesive to the back side and mitered joint of the corner and set it into place. Snug it into
place. The corner is shipped in two pieces and requires assembly before installation.
3. Fasten Corner Pieces
Fasten the corner piece with nails or screws. Continue with all other inside and outside corners of the roof.
4. Determine Moulding Lengths
Using your roof-line layout drawing as a guide, measure the length of the first trim piece you need. To ensure a snug fit on longer lengths, add
¼" every ten feet. Transfer your measurement ((¼” every ten feet and cut the first piece to length. Check the fit by laying the piece in place.
5. Apply Adhesive and Set Moulding Into Place
Apply a bead of adhesive to the surfaces that the E-Vent will touch. Lay the first piece into place. Note: Because you cut them slightly long,
some pieces will spring into place, and will be slightly bowed. This is normal. The piece will flatten as it is screwed into the wall.
6. Fasten The Moulding
Starting with the ends first, attach the E-Vent with fasteners. Work toward the middle, driving nails or screws every 16". Again, the extra ¼”
every ten feet will flatten as you move toward the center. Continue to install the E-Vent system, until the entire system is done.
7. Patch Holes & Touch Up or Paint
General Installation Notes
Any adhesives, sealants, fillers or paint used must be compatible with the material that is being installed (see manufacturer’s recommendations in the
Finishing and Adhesives section below). Always use corrosion-resistant mechanical nails or screws along with manufacturer’s recommended adhesive
product when installing all Fypon products. This combination provides a secure, long-lasting bond. Countersink all fasteners about 1/8” and fill with
product compatible filler. Exterior installations should be finished using a manufacturer’s recommended caulk to prevent water infiltration behind
siding, windows and doors. Some exterior installations, in particular new construction before siding is applied, may require a J-channel and/or
flashing to prevent water infiltration. Installers must determine which installation technique is best for the specific situation.
Finishing and Adhesives
Polyurethane (PUR) – Fypon polyurethane products are factory primed. Depending on product location, always use interior/exterior-grade, PUR
compatible adhesives, sealants, and fillers when installing Fypon products. Consult the manufacturer’s recommendations for your particular
climate and the substrate you are installing to.
Cellular PVC – Depending on product location, always use interior/exterior-grade, PVC compatible adhesives, sealants, and fillers when installing
Fypon products. Consult the manufacturer’s recommendations for your particular climate and the substrate you are installing to. If painting is
desired, a 100% acrylic latex paint with a Light Reflectance Value (LRV) of 55% or higher must be used. Applying paint with an LRV of 54% or
lower will void the warranty.
IMPORTANT:
Please read these installation guidelines thoroughly before beginning installation. Please note that these guidelines are provided only to assist with the installation of Fypon moulding
and millwork products. Modified procedures may be required in order to meet specific situations, unique applications and local building codes. The manufacturer does not, under any
circumstances, warrant the installation of its products. Be sure to wear appropriate protective clothing, gloves and safety glasses when working with any tools. Installer should check
for and relocate all electrical wiring within the proposed installation area, as needed (be sure to disconnect all electric power before working with any electrical wiring and follow all
applicable local electrical codes and safety procedures).
Fypon, Ltd. 1750 Indian Wood Circle Maumee, Ohio 43537 1.800.446.3040 www.fypon.com
Loading...