Page 1
F(x)tec Pro
1
QUICK START GUIDE
OTHER LANGUAGE 2
OTHER LANGUAGE 3
OTHER LANGUAGE 4
OTHER LANGUAGE 5
OTHER LANGUAGE 6
2
10
13
17
20
27
Page 2
QUICK START GUIDE
Thank you for choosing the Pro1. Before using the device, please
read this guide to help you get started. The full User Guide is
available at www.fxtec.com/support.
Getting To Know Your Phone
Familiarise yourself with the different parts of the phone as shown in
the diagram below.
Front
Camera
Proximity Sensor
Sim Card Tray
+ Micro-USB Port
Earpiece
Indicator
Volume Keys
Power Button
Fingerprint Reader
Camera
Button
pg. 2
Rear Camera
Flash
Charger Microphone
Headset
Connector
Loudspeaker
Page 3
Sliding Your Phone Open
1. Lift the right side of the Pro1 up slightly.
2. Slide the screen up until the hinge locks into position
1
2
3
pg. 3
Page 4
Inserting and Removing the SIM card
1. To open the SIM card tray, place your ngernail into the ridge and
carefully slide the tray out.
2. Put the nano-SIM card into the slot located on the tray with the
contact area facing down.
3. Slide the SIM card tray back into the slot.
1
2
pg. 4
3
Page 5
Charging Your Phone
To charge the phone, use the charger provided with your phone.
The charger type may vary according to country. Please use the one
that is relevant to your region. Plug the charger into a wall outlet
and connect the cable to the phone. A charging indicator will be
displayed to indicate the phone is charging.
Once fully charged, press and hold the Power button until the screen
lights up to switch your phone on.
The screen prompts will guide you through the setup.
Indicator
Power Button
pg. 5
Page 6
Safety Information
Read all safety information before using the device to prevent
injury to yourself or others, to prevent damage to your device
and to avoid breaking local laws and regulations. See the
full ‘Important Safety Information’ at www.fxtec.com/support.
Handle Device with Care
The screen of this device is made of glass. This glass can break if the
device is dropped or receives a substantial impact. Should the glass
break, do not touch the glass parts or attempt to remove the broken
glass.
Get the glass replaced by an authorised service personnel before
using the device.
Batteries, Chargers and Other Accessories
Only use manufacturer approved battery, charger and accessories for
this device. Do not use incompatible batteries or chargers as this may
cause re, explosion, or other hazards. Using incompatible products
may also damage your device and invalidate the warranty.
Protect Your Hearing
Road Safety
Obey local laws and regulations. Keep your hands free to operate the
vehicle while driving.
Switch off in Restricted Areas
Obey all instructions in restricted areas. All wireless devices may be
susceptible to interference.
Switch your device off when mobile phone use is not allowed or
when it may cause interference. Be aware of restrictions in areas such
as in hospitals, near petrol pumps, during ights or near medical
equipment.
Authorised Service
Only send this device to authorised service personnel for repairs or
installations.
Do not open the device other than as instructed in the user guide.
Unauthorised modications may damage the device and violate
regulations and invalidate the warranty.
Keep Device Dry
This device is not waterproof and has no IP rating. Exposure to liquid,
moisture and humidity can damage the parts or electronic circuits of
the device.
Specic Absorption Rate (SAR)
This device meets RF exposure guidelines when used either in the
normal use position against the ear or when positioned at least 5mm
away from the body.
Mobile devices may be transmitting even when not on a voice call.
Ensure that any carry case, belt clip or other form of device holder
does not contain metal and should provide at least 5mm separation
distance from the body.
Do not listen at high volume levels for
long devices. Use caution when holding the
device near your ear while the loudspeaker is in use.
pg. 6
Page 7
Correct Disposal
The crossed-out wheelie bin symbol on your device,
battery or packaging is a reminder that all electrical
and electronic products and batteries must be taken to
a separate collection point at the end of their working life.
DO NOT dispose of these products as unsorted municipal waste.
Always recycle your devices, batteries and packaging materials to
dedicated recycling points.
Check with your local waste authority for information on your nearest
recycling point.
Regulatory Information: EU
EU Compliance Notice
Hereby, FX Technology Limited declares that Pro1 is in compliance
with Directive 2014/53/EU (Radio Equipment Directive). The full
declaration of conformity is below:
EU Declaration of Conformity
FX Technology Limited
This declaration of conformity is issued for:
Radio Equipment model number: QX1000
Product name: Pro1
Software version: Android OS
Accessories supplied: USB-C earbud, AC adapter,
USB-C to C cable
We, FX Technology Limited, declare under our sole responsibility that
the above named product(s) conform to the essential requirements
of the following European Union directives:
Radio Equipment Directive (RED) 2014/53/EU
RoHS Recast Directive 2011/65/EU
Ecodesign Requirements for Energy 2009/125/EC
Related Products Directive
The conformity assessment procedure referred to in Article 10 and
detailed in Annex III of the Radio Equipment Directive 2014/53/EU
has been carried out by Notied Body Name: STS Labs, Number:
STS1906274. The following harmonized standards and normative
documents are those to which the product’s conformance is
declared, and by specic reference to the essential requirements of
the referenced Directives:
Health & Safety IEC 60950-1:2005 + A1:2009 + A2:2013
(Article 3.1(a) of the RED) EN 60950-1:2006 + A11:2009 +
A1:2010 + A12:2011 + A2:2013
IEC 62368-1:2014, EN 62368-1:2014 +
A11:2017
EN 62311:2008, EN 62479:2010
EN 50360:2017, EN 62209-1:2016
EN 50566:2017, EN 62209-2:2010
EMC Draft EN 301 489-1 v2.2.0
(Article 3.1(b) of the RED) Final Draft EN 301 489-3 V2.1.1
Draft EN 301 489-17 V3.2.0
pg. 7
Page 8
Draft EN 301 489-19 V2.1.0
Draft EN 301 489-52 V1.1.0
EN 55032:2015/AC:2016 Class B
EN 55035:2017
Spectrum EN 300 328 v2.1.1
(Article 3.2 of the RED) EN 301 893 v2.1.1 EN 301 511 V12.5.1
EN 301 908-1 V11.1.1, EN 301 908-2
V11.1.2,
EN 301 908-13 V11.1.2
EN 300 328 V2.1.1, EN 301 893 V2.1.1
EN 303 413 V1.1.1, EN 300 330 V2.1.1
Draft EN 300 440 V2.2.0
EN 303 417 V1.1.1
Equipment within Certain N/A
Categories or Classes
(Article 3.3 of the RED)
Ecodesign Requirements Regulation 1275/2008, Regulation for
Energy Related 278/2009
Products Directive,
2009/125/EC
RoHS Recast Directive, EN 50581:2012
2011/65/EU
Signed for and on the behalf of FX Technology Limited
Restrictions and Requirements under Directive 2014/53/EU
The device is restricted to indoor use only when operating in the
5150 to 5350 MHz frequency range in AT, BE, BG, CY, CZ, DE, DK, EE,
EL, ES, FI, FR, HR, HU, IE, IT, LT, LU, LV, MT, NL, PL, PT, RO, SE, SI, SK, UK,
CH, IS, LI, NO, and TR.
Frequency Bands and Power
European Union, United Kingdom
Data given here is the maximum radio-frequency power transmitted
in the frequency band(s) in which the radio equipment operates.
Frequency Power
WiFi 2 400-2 483,5 MHz Max 20 dBm
WiFi 5 150-5 250 MHz Max 23 dBm
WiFi 5 250-5 350 MHz Max 23 dBm
WiFi 5 470-5 725 MHz Max 23 dBm
WiFi 5 745-5 825 MHz Max 14 dBm
Bluetooth: 2 400-2 483,5 MHz Max 20 dBm
NFC 13.56 MHz Max. -10 dBuA/m
GSM 900 PC4 (Max 33.5 dBm)
GSM 1800 PC1 (Max 30.5 dBm)
UMTS Band I/VIII PC3 (Max 24.5 dBm)
LTE:1, 3, 7, 8, 20, 28, 38, 40, 42 PC3 (Max 24.5 dBm)
Restrictions in the 5 GHz Band
WLAN function of these devices is restricted only to indoor use when
operating in the 5150 to 5350 MHz frequency range to reduce the
potential for harmful interference to co-channel mobile satellite
systems.
pg. 8
Page 9
Radio frequency interference
FX Technology Limited is not responsible for any radio or television
interference caused by unauthorized modication of these devices
or accessories, or by the substitution or attachment of connecting
cables and equipment other than that specied by FX Technology
Limited. The correction of interference caused by such unauthorized
modication, substitution, or attachment is the responsibility of
the user. FX Technology Limited and its authorized resellers or
distributors are not liable for any damage or violation of government
regulations that may arise from the user failing to comply with these
guidelines.
Specic Absorption Rate (SAR) information - EU
This device is classied for use in a typical Class B domestic
environment.
The Pro1 complies with radio frequency specications when used
near your ear or at a distance of 0.5 cm from your body. Ensure that
the device accessories, such as a device case and device holster, are
not composed of metal components. Keep the device away from
your body to meet the distance requirement.
The highest Specic Absorption Rate (SAR) value reported for this
device type when tested at the ear is 0.375 W/kg, and when properly
worn on the body is 0.397 W/kg.
Waste Electrical and Electronic Equipment (WEEE) & Batteries
Directive
The Waste Electrical and Electronic Equipment
(WEEE) Directive requires that all Electrical
and Electronic Equipment (EEE), including
your phone and its accessories, must be marked
with the symbol of the crossed-out wheeled bin.
This symbol means that the equipment must
not be disposed of as unsorted municipal waste.
Disposing of WEEE together with normal waste may pose a risk to the
environment and to human health, due to certain substances used in
EEE and their batteries.
Under the WEEE Directive, each EU Member State is responsible for
achieving a high level of collectionof WEEE for treatment, recovery,
and environmentally sound disposal.
The success of this EU policy will depend on your active contribution
in returning your WEEE to the appropriate facilities dedicated to
the disposal of such waste. You should contact your local authority
or your retailer for details about the return and collection points
available.
RoHS Compliance
This product is in compliance with Directive 2011/65/EU of the
European Parliament and of the Council of 8 June 2011, on the
restriction of the use of certain hazardous substances in electrical and
electronic equipment (RoHS) and its amendments.
REACH
REACH (Registration, Evaluation, Authorization and Restriction of
Chemicals, EC No 1907/2006) is the EU regulation addressing
the safe production and use of chemicals. FX Technology Limited
complies with all requirements of the regulation.
Manufacturer Info
Manufacturer: FX Technology Limited.
pg. 9
Page 10
Regulatory information: United States
U.S. Federal Communications Commission’s (FCC) Regulatory
Compliance
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for
help
• Changes or modications not expressly approved by FX
Technology Limited could void your authority to operate the
equipment.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
Radio Frequency Exposure
This device meets the U.S. Federal Communications Commission’s
(FCC) requirements for exposure to radio waves and is designed
and manufactured not to exceed the FCC’s emission limits for
exposure to radio frequency (RF) energy. For satisfying FCC RF
exposure compliance requirements, body-worn operations are
restricted to belt clips, holsters or similar accessories that have no
metallic components in the assembly and must provide at least 10
mm separation between the device, including its antenna, and the
user’s body.
Specic Absorption Rate (SAR) Information
This device is designed to meet the requirements for exposure
to radio waves established by the Federal Communications
Commission (USA).
The Specic Absorption Rate (SAR) limit adopted by the U.S. is 1.6 W/
kg averaged over one gram of tissue. The highest SAR value reported
to the FCC for this device type complies with this limit. The Pro1
complies with radio frequency specications when used near your
ear or at a distance of 1.0 cm (0.4 in) from your body. Ensure that the
device accessories, such as a device case and device holster, are not
composed of metal components. Keep the device away from your
body to meet the distance requirement.
Pro1 maximum SAR values as reported to the FCC are:
• 0.375 W/kg when holding it to your ear
• 0.397 W/kg when properly worn on the body
pg. 10
Page 11
Hearing Aid Compatibility (HAC)
The Pro1 has been evaluated and certied to be compatible with
hearing aids per technical specication ANSI C63.19-2011. There are
two measures of hearing aid compatibility:
M rating, which is a measure of immunity to radio frequency
interference for acoustic coupling hearing aids; and T rating, which
is a measure of performance when used with an inductive coupling
(telecoil) hearing aid.
The Pro1 is rated M3/T3.
Per FCC rules, a mobile phone is considered hearing aid compatible
if rated M3 or M4 for acoustic coupling or T3 or T4 for inductive
coupling.
The Pro1 has been tested and rated for use with hearing aids for
some of the wireless technologies that they use. It is important to
try the different features of your phone thoroughly and in different
locations, using your hearing aid or cochlear implant, to determine if
you hear any interfering noise. Please consult your service provider or
FX Technology Limited for information on hearing aid compatibility.
If you have questions about return or exchange policies, consult your
service provider or phone retailer.
The Pro1 meets the hearing aid compatibility (HAC) requirements set
by the Federal Communications Commission (FCC).
Regulatory information: Canada
Innovation, Science, and Economic Development (ISED) Canada,
Class B
This Class B digital apparatus complies with Canadian ICES-003.CAN
and ICES-3(B)/NMB-3(B).
Notice: The ISED Canada regulations provide that changes or
modications not expressly approved by FX Technology Limited
could void your authority to operate this equipment.
Innovation, Science, and Economic Development (ISED) Canada
Notices
The Pro1 complies with ISED’s license-exempt RSS standard(s).
Operation is subject to the following two conditions:
1. These devices may not cause interference.
2. These devices must accept any interference, including
interference that may cause undesired operation of the device.
The device for operation in the band 5150–5250 MHz is only for
indoor use to reduce the potential for harmful interference to cochannel mobile satellite systems.
Specic Absorption Rate (SAR) Information
The radiated output power of the Pro1 is below the ISED radio
frequency exposure limits. This device has been evaluated for and
shown compliant with the ISED Radio Frequency (RF) exposure limits.
This device should be used in a manner such that the potential for
human contact during normal operation is minimized.
When using the device next to your body (other than in your hand
or against your head), maintain a distance of 10 mm from your body,
to be consistent with how the device is tested for compliance with
RF exposure requirements. Ensure that the device accessories, such
as a device case and device holster, are not composed of metal
components.
pg. 11
Page 12
Pro1 maximum SAR values as reported to the ISED are:
• 0.375 W/kg when holding it to your ear
• 0.397 W/kg when properly worn on the body
This device has been certied for use in Canada.
Status of the listing in the ISED’s REL (Radio Equipment List) can be
found at the following web address:
http://www.ic.gc.ca/app/sitt/reltel/srch/nwRdSrch.do
Additional Canadian information on RF exposure also can be found
at the following web address:
http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08792.html
Regulatory information: Japan
When operating in 5GHz (W52/W53), the device is restricted to
indoor use only (except for the transmission with 5.2GHz High Power
Data Communication System Base Station or Relay Station).
This is a Class B equipment. Although this equipment is intended for
use in a residential environment, it could cause poor reception if used
near a radio or a television receiver. Please follow instructions in the
instruction manual.
VCCI-B
The Pro1 complies with Japan SAR regulations when used near
your ear or at a distance of 5 mm from your body. Ensure that the
device accessories, such as a device case and device holster, are not
composed of metal components. Keep the device away from your
body to meet the distance requirement.
Pro1 maximum SAR values as reported to the Japan Ministry of
Internal Affairs and Communications (MIC) are:
• 0.375 W/kg when holding it to your ear
• 0.397 W/kg when properly worn on the body
pg. 12
Page 13
pg. 13
Loading...