1
User Manual for Future Call Talking Caller ID Box with Call
Blocking FC-0215
USER MANUAL
• Please follow instructions for repairing if any otherwise do not alter or repair any parts of device except
specified.
IMPORTANT SAFETY INSTRUCTIONS
Before using your talking caller ID box with call blocking, basic safety precautions should always be
followed to reduce the risk of fire, electric shock and injury to persons including the following:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product.
3. Unplug this product from the wall outlet before cleaning. Do not use liquid or Aerosol cleaners. Use a
damp cloth for cleaning.
4. Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry
tub, in a wet basement or near a swimming pool.
5. Do not place this product on an unstable cart, stand, or table. The product may fall causing serious
damage to the product.
6. Slots and openings in the enclosure and the back and bottom are provided for ventilation, to protect it
from overheating. These openings must not be blocked or covered. The openings should never be
blocked by placing the product on a bed, sofa, rug, or another similar surface. This product should never
2
be placed near or over a radiator or heat register. This product should not be placed in a built-in
installation unless proper ventilation is provided.
7. This product should be operated only from the type of power source indicated on the marking label. If
you are not sure of the type of power supply to your home, consult your dealer or local power company.
8. Do not allow anything to rest on the power cord. Do not locate this product where the cord will be
abused by persons walking on it.
9. Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock.
10. Never push objects of any kind into this product through cabinet slots as they may touch dangerous
voltage points or short out parts that could result in a risk of fire or electric shock. Never spill liquid of any
kind on the product.
11. Do not disassemble this product, but take it to a qualified service technician or service center when
repair work is required. Opening or removing covers may expose you to voltage or other risks. Incorrect
reassembly can cause electric shock when the appliance is subsequently used.
12. Unplug this product from the wall outlet and refer to qualified service personnel under the following
conditions:
A. When the power supply cord or plug is damaged or frayed.
B. If liquid has been spilled into the product.
C. If the product has been exposed to rain or water.
D. If the product does not operate normally by following the operating instructions. Adjust only those
controls that are covered by the operating instructions. Improper adjustment of other controls may result in
damage and may require extensive work by a qualified technician to restore the product to normal
operation.
E. If the product has been dropped or the enclosure has been damaged.
F. If the product exhibits a distinct change in performance.
13. Avoid using a telephone during an electrical storm. There may be a remote risk of electric shock from
lightning.
14. Do not use the telephone to report a gas leak in the vicinity of a leak.
15. Never install telephone wiring during a lightning storm.
16. Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.
17. Never touch uninsulated telephone wires or terminals unless the telephone line has been
disconnected at the network interface.
Installation
1. Please plug in the 5 VDC AC adapter before using this product.
2. Please plug in the line cable from the wall jack into the LINE IN socket. You can now plug your
Telephone into the PHONE socket but this is optional.
3
SAVE THESE INSTRUCTIONS
1
Delete key
6
DC Socket (5V)
2
Dial/ Confirm key
7
Phone Socket
3
White-list key
8
Line Socket
4
UP 9 Battery Slot
5
DOWN
10
Desk Bracket
Function description：
1. FSK single data and compound data TYPEI, TYPEII, compatible with receiving both data, comes
with call waiting function.
2. LCD can display 13 digits and 11 numbers.
3. Two languages: English and Spanish; English set as default.
4. Caller ID Functions：
(1) Support call back function for incoming numbers in US;
（2）Deletion for Incoming call records and full deletion function;
（3）Reviewing incoming calls records, quick review function;
4
（4）99 groups of incoming calls;
（5）50 groups of white-list numbers, recording for the name in the white-list.
（6）Talking the name or numbers when the calls come in.
（7）icon Indications on the LCD for new incoming calls, Voice mail, Low Battery, AM-PM, RPT, and
VIP.
5. Dialing System: DTMF
6. Back light Function：
8 seconds back light for ringing, keys operation, and phone pick up & hang up. The back light will
turn off after 8 seconds if no more operation is done.
7. Clock System：
12-hour real-time clock display and setting function, month and day format. (Not year)
8. LCD Contrast：
5 Levels of contrast settings, 4
th
level set as default.
9. Saving information when the power down：
When there is no external power supply, it enters the STOP mode, keeping the information from
being lost.
10. Talking the numbers when white-list call comes in.
The white-list calls with name recording can talk the names 0-5 times, if someone sets it to “0”
the speaker will keep silence and will not say any names or numbers until it is set back to 1-5. Calls
not in the white-list will only talk the numbers if the block function is OFF.
Functions & Operation
1. Note: Please use the AC adapter before using this product. Once you plug in the adapter or
put in batteries, the LCD will show “Welcome to Future Call Model FC-0215 + Version
number in page-turn display, and back to normal display in 5 seconds.
2. Back to default setting. Hold and press DEL key first and then plug in the adapter or put in
batteries. The LCD will show “LOAD DEFAULTS” and then after 3 seconds it will show the
word “DONE” on the LCD. Now you can release the DEL key, the box is back to default
setting, then the LCD will show “Welcome to Future Call Model FC-0215 + Version
number”in page-turn display, and back to normal display.
5
3. Battery Notice: We suggest to use 4 Alkaline batteries type AAA 1000mAh as backup
power for normal use. Batteries will last about 3-4 days if there’s no power from the AC
adapter. When the batteries are in low power mode, you will see a low battery icon showing
on the LCD, which means you need to change the batteries as soon as possible.
2.1. Menu Setting:
1) Language settings:
Press DIAL key to enter main menu setting, the LCD will show: “Set Language”, press DIAL again
to confirm and enter the language option. The LCD will show “English”, press “UP/DOWN” to choose
the language you want, then press DIAL to confirm. Press UP/DOWN to choose other menu settings
or choose “Exit Options” then press DIAL key to exit.
2) White-list Setting：
After pressing DIAL key to enter the main menu, press UP key just once the LCD will show “Store
Number”, press DIAL key to confirm and enter into the white-list setting, The LCD will show “Input
Number”, after one second press UP/DOWN keys to choose the digit, you want to store. Press
DIAL key to confirm the digit, and continue this process until you have set all digits of the telephone
number you wish to store (If you have stored a digit by mistake, use the DEL key to delete the digit).
Once you finished to store the number, If you would like to just add this number without giving a
name recording, just push red OK key to save this number into the white-list and the LCD will show
“SAVED”; If you would like to add this number with a name recording, please push DIAL key again
the LCD will show the word “Recording”, start the recording immediately. Please note you can only
record for 3 seconds and please note when recording the name there must be silence no background
noise, No AC, Fans, TV etc. Once the recording is done, it will play it back to you automatically.
Note: You must set the numbers from left to the right.
3) LCD Contrast Adjustment：
After pressing DIAL key to enter the main menu, press the UP key 2 times, the LCD will show: "LCD
Contrast", press the DIAL button to confirm and enter the LCD contrast adjustment setting. The LCD
will display: "Contrast 4", press the UP/DOWN button to select the contrast setting. After the setting,
press the DIAL key to confirm. The LCD display will show “Area Code”. Press UP/DOWN to choose
other menu settings or choose “Exit Options” then press DIAL key to exit.
6
4) Area Code Setting：
After pressing DIAL key to enter the main menu, press the UP key for 3 times until the display
shows “Area Code”, press DIAL key to confirm and enter the Area Code Menu Setting. The LCD
will display “Area Code”, press UP/DOWN keys to select the first digit of the local area code and
press the DIAL key to confirm and skip to the next digit. After finishing the setting, press DIAL key
to confirm and return to the “Set Voice”. Press UP/DOWN to choose other menu settings or choose
“Exit Options” then press DIAL key to exit.
Note: You must set the area code 3 digits to the area code of the line the caller ID box is
connected to. E.g., If your phone number is 480-759-2255 your area code must be set to 480
Note: All 3 digits local area codes must be set from left to the right;
5) Voice Setting for white-list numbers.
After pressing DIAL key to enter the main menu, press the UP button 4 times, the LCD will display:
"Set Voice”, press the DIAL button to confirm and enter the Voice Setting. The LCD will display:
"Set Voice 0", press UP/DOWN key to select 0-5, “0” means turn off talking numbers/names, and
this unit will keep silence whenever calls come in and if you’re looking over the white- list or call
records. 1-5 means the times of talking the names when you receiving the incoming calls. After the
setting done, press DIAL key to confirm and return to the ‘Set Time and Date setting’ Press
UP/DOWN to choose other menu settings or choose “Exit Options” then press DIAL key to exit.
Please note: This will only work for the numbers with a name recording in the white-list, if there’s a
number in the white-list without giving a name, then it will talk this number only one time when the
call comes in.
6）Date and Time Setting：
After pressing DIAL key to enter the main menu, press the UP key 5 times, the LCD will display:
"Set Time/Date", press the DIAL button to confirm and enter the date and time setting, the LCD will
display: "TIME/DATE", hour is flashing, press the UP/DOWN button to select the hour, press DIAL
key to confirm and enter the minute setting. The adjustment sequence is hours, minutes, month and
day. After finishing the setting, press DIAL key to confirm and return to the “SET BACKLIGHT” Press
UP/DOWN to choose other menu settings or choose “Exit Options” then press DIAL key to exit.
Note: The time and date will automatically set up itself on the first incoming call.
7) Back light Setting:
After pressing DIAL key to enter the main menu, press the UP key 6 times, the LCD will display:
"Set Backlight", press DIAL key to enter and then press UP/DOWN key to choose ON or OFF to turn
7
on or off the backlight. After finishing the setting, press DIAL key to confirm return to the “Block setting”
Press UP/DOWN to choose other menu settings or choose “Exit Options” then press DIAL key to exit.
8）Block Setting:
After pressing DIAL key to enter the main menu, press the UP key 7 times, the LCD will display: “Block”,
Press DIAL key to confirm, and then press UP/DOWN to choose ON or OFF to turn on or off the block
function. After finishing the setting, press DIAL key to confirm and return to the “Exit Option” Press
UP/DOWN to choose other menu settings or choose “Exit Options” then press DIAL key to exit.
Note: When a nonwhite-list call comes in, the phone will ring just once and then stop the calls
automatically. If there are a few phones which are connected on the same line in parallel, the box will
stop all the phones on the same line from ringing, not only the phone that is plugged into the box itself.
9）Exit to the menu：
After all the settings are finished, choose the menu “Exit Options”, press DIAL to exit.
2.2. Caller ID Function：
1. Save the caller IDs and display：
(1) Display after receiving an incoming call：
After receiving a group of new incoming calls, the incoming call number will remain displayed on the
LCD for 10 seconds. During this period, after receiving a new ring tone, it will continue to display for
10s and the ‘New Call’ icon will be displayed at the same time.
(2) Incoming call information storage：
Caller information will save caller ID numbers, names, call time, and icon of new calls.
(3) Records of calls：
Caller information will be recorded in order, when the storage is full, the latest call records will replace
automatically the oldest calls.
(4) Cancellation of new call records:
After the new call record is reviewed, the new call icon will be no longer be displayed; after the call
is received and the handset is picked up, the new call icon will be no longer displayed as well.
(5) How to handle Repeated incoming calls and repeated new calls icon:
8
When a new caller ID number is the same as the previous old caller ID number from the call records,
then the call record for the previous one will be replaced by the recent call; If the previous caller ID
number is a new incoming call, then the RPT icon will be lit up. When you are looking over the RPT
numbers, the RPT icon will not disappear, when there is a new caller and this number is the same as
the RPT numbers, then the RPT icon will disappear, as the RPT icon will light up only when the new
incoming call comes in.
2. Reviewing the Call records:
Press the DOWN key to view the incoming calls from the last group, press the UP key to view the
incoming calls from the first group, if there is no information, it will display "NO CALLS", and between
the first group of records and the last group of records, it will display "END OF LIST".
3. Delete the caller information and full deletion.
（1）Delete a group of incoming calls:
In the off-hook or on-hook state, press the UP or DOWN key to select the call you want to delete, press
the DEL key once, "Delete?" is displayed on the screen, press the DEL key again to confirm and delete
the group of incoming calls. The LCD displays the next incoming call, If you don’t want to delete, you
can press UP/DOWN to exit and continue to check.
(2) Delete all incoming calls:
In the off-hook or on-hook state, press the UP/DOWN key to display any incoming call, press and hold
the DEL key for 3 seconds, the display changes to "DEL ALL CALLS?", press the DEL key again to
display "NO CALLS", all the memories will have been deleted.
4. Save the Incoming call number to the whitelist:
In the on-hook state, press the UP or DOWN key to display any incoming call, and press the red OK
key (Add to the Whitelist key) to get this number into the white-list, press DIAL key to confirm and enter
“Recording...” to start the recording, please note you can only record for 3 seconds and please when
recording the name there must silence no background noise, No AC, Fans, TV etc. Now the name
recording is set! Please note just push OK key to save this number into whit-list directly if you don’t
need a name recording for this number.
How to delete a number in the white-list? Push the red OK key to enter the white-list, and use UP
and DOWN key to find the number that you want to delete, push DEL key once and the LCD shows
“Delete?”, press the DEL key again to confirm and this number is deleted. And if you want to delete all
the numbers in the white-list at one time, then hold and push DEL key for 3 seconds the LCD will show
“Del All Calls?”, push the DEL key again to display "NO CALLS", all the numbers from white-list have
9
been deleted now.
5. Call Waiting (CW) Function:
When you are talking on the 1st call, on handset or speaker mode, and the 2nd call is calling, you can
hear a beep sound and the number from the 2nd call will show on the LCD, press flash key to answer
the 2nd call and then press the flash key again to get back the 1st call. (Note: the number from 2nd call
will show on LCD even it’s from white-list or nonwhite-list)
Note: The call waiting function in this unit will not work well when using a telephone without
call waiting function and also not supported by your telephone provider.
6. Call back the calls records:
On-hook state:
1． Use UP/DOWN to select the numbers you want to call back, press DIAL key to confirm the
number, and pick up the handset of the phone, it will then dial out automatically the number.
2. There are only three situations where you can adjust the number to call back: the number is 10
digits; the 7-digit local number shows that the 3-digit area code has been filtered out; the 7-digit local
number shows that the long-distance number 1 and the 3-digit area code have been filtered out. By
pressing the DIAL key, the number will be adjusted according to the following conditions:
（1） The 7-digit，local number, which also displays the 3-digit area code or the 7-digit local
number that has been filtered out, and the long-distance number 1 and 3-digit area code
that have been filtered out: Press the DIAL key once, the LCD displays the 7-digit
number, and press the DIAL key again the LCD displays 10-digit number, press DIAL
key again, LCD displays 11-digit number. When you see the number, you want to dial,
pick up the handset of the phone and it will dial out automatically the number displayed.
（2） For a 10-digit number displayed on the LCD, press the DIAL button once, the LCD
displays 11 digits, press the DIAL button again, the LCD displays 10 digits, and press
the DIAL button again, the LCD displays 7 digits When you see the number you want
to dial pick up the handset of the phone and it will dial out automatically the number
displayed.
（3） Note: You must set the area code 3 digits to the area code of the line the caller ID box
is connected to. E.g., If your phone number is 480-759-2255 your area code must be
set to 480
7. Indication for new incoming calls：
10
a) When there is a new call record, in the on-hook state, the back light will be lit for 10 seconds, and
the new call icon on the LCD will light up; after the new call record is reviewed, the new call icon will
disappear.
b) Note:
After the incoming call is received and the handset is picked up, the new incoming call icon will
disappear.
8. Talking the names when the calls come in:
A). You can set the talking times on menu setting when the calls from the white-list come in;
It will only talk the numbers, NOT the name, when the call is not in the white-list.
B). There is a preprogrammed 10 second announcement for an incoming call that is not in the
white list. After the announcement the call will be disconnected.
9. Voice Mail:
a）There is an icon on the LCD for Voice mail.
b）Function：
To use the voice mail function, you must apply for this service at your local telephone company
1) If the voice mail message is sent after the ring tone, the message can be received. The mailbox
icon on the LCD will be lit. In the on-hook state, the mailbox icon will be flashing. The time
period is about 200MS every 2 seconds.
2) After checking the mailbox, the telephone company will send a clear signal, and the mailbox icon
will disappear. Alternatively, after receiving this signal; you can also delete the mailbox icon
manually: when there is a voice mailbox prompt, press and hold the DEL key for 3 seconds,
the LCD will display: MSG WAITING OFF, the voice mailbox record will be cleared.
10. Back light function:
The back light will come on if there is an incoming ring, key operation, and parallel machine
pick-up or hang-up operation, it will stay on for 8 seconds. If there is no operation within 8
seconds, then the backlight will turn off.
11
CONSUMER INFORMATION
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA On the
bottom of this equipment is a label that contains, among other information, a product identifier of US: If
requested, this number must be provided to the telephone company.
The applicable jacks (i.e., RJ11C) for this equipment are provided in the packaging with each piece of
approved equipment. The jacks are certified by Universal Service Order Codes (USOC).
A plug and jack used to connect this equipment to the premises wiring and telephone network must
comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant
telephone cord and modular plug are provided with this product. They are designed to be connected to a
compatible modular jack that is also compliant. See installation instructions for details.
The REN is used to determine the number of devices that may be connected to a telephone line.
Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call.
In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of
devices that may be connected to a line, as determined by the total RENs, contact the local telephone
company. [For products approved after July 23, 2001, the REN for this product is part of the product
identifier that has the format US: AAAEQ##TXXXX. The digits represented by ## are the REN without a
decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label.
If this equipment FC-0215 causes harm to the telephone network, the telephone company will notify you in
advance that temporary discontinuance of service may be required. But if advance notice isn’t practical,
the telephone company will notify the customer as soon as possible. Also, you will be advised of your right
to file a complaint with the FCC if you believe it is necessary.
The telephone company may make changes in its facilities, equipment, operations or procedures that
could affect the operation of the equipment. If this happens the telephone company will provide advance
notice in order for you to make necessary modifications to maintain uninterrupted service.
If you experience trouble with this equipment, disconnect it from the network until the problem has been
corrected or until you are sure that the equipment is not malfunctioning.
Please follow instructions for repairing if any (e.g., battery replacement section); otherwise, do not alter or
repair any parts of device except specified.
Connection to party line service is subject to state tariffs. Contact the state public utility commission, public
service commission or corporation commission for information.
This equipment is hearing aid compatible.
NOTICE: If your home has specially wired alarm equipment connected to the telephone line, ensure the
installation of this equipment FC-0215 does not disable your alarm equipment. If you have questions
about what will disable alarm equipment, consult your telephone company or a qualified installer.
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
SERVICE: According to FCC regulation. This equipment which has been certified and registered by the
FCC, may only be repaired by authorized person, the FCC certification may be voided. Should you
encounter any problems, please call the FUTURE CALL LLC.
Toll-free Customer Hotline for assistance:
1-888-934-CALL, Monday - Friday between the hours of 9:00 am - 6:00 pm PST
12
For general inquires, you can E-Mail to help@future-call.com or visit our website at www.future-call.com
FOR WARRANTY AND OUT-OF WARRANTY SERVICE:
You may call our toll-free hot line on 1-888-934-CALL (1-888-934-2255) 9AM-6PM PST or E-mail
to help@future-call.com
QUESTIONS?
STOP...doesn’t take unit back to the store.
LOOK...for the toll-free “help” telephone number.
LISTEN... as our experts talk you through the problem.
For immediate answers to your questions regarding operation, missing parts or installation call:
FUTURE CALL LLC
HOTLINE & E-MAIL AT:
1-888-934-CALL & help@future-call.com
LIMITED WARRANTY AND SERVICE
FUTURE CALL LLC. warrants this product to be free from defective materials or factory workmanship and
will replace or repair this unit or any part thereof, except batteries, if it proves to be defective in normal use
or service within 90 days from
date of original purchase. Our obligation under this warranty is the repair or replacement of the defective
instrument or any part thereof, except batteries. This warranty will be considered void if unit is tampered
with, improperly serviced, or subjected to misuse, negligence or accidental damage. There are no other
express warranties other than those stated herein.
This warranty gives you specific legal rights, and you may also have other rights which varies from state to
state. TO OBTAIN SERVICE PLEASE E-MAIL US ON help@future-call.com OR CALL US TOLL FREE 1888-934-CALL 9AM-6PM PST (1-888-934-2255). IF THE UNIT IS UNDER WARRANTY PROOF OF
PURCHASE MUST BE PROVEN.
Loading...