Future Beach WB 200, WB 202, WB 203, WB 400 Owner's Manual And Assembly Manual
Water Bee Pedal Boats
Owner’s Manual and Assembly Guide
(Models: WB 200, WB 202, WB 203, WB 400)
www.futurebeach.com
At Future Beach™, customer satisfaction is our top priority.
For all inquiries and product support contact us at:
1-800-357-7837 y info@futurebeach.com
Future Beach
™ is publicly traded on the TSX Venture Exchange, symbol FBC
Water Bee™ Pedal Boat Owner’s Manual and Assembly Guide
Introduction
Future Beach
Water Bee
™, The World’s Beach Company™, congratulates you on the purchase of your
™ pedal boat.
At Future Beach™, we are proud of our world-class product designs, workmanship, and quality.
Since our inception, the complete and permanent satisfaction of our customers has always been
our primary concern.
This manual will outline your Water Bee’s assembly instructions, product care, safety issues, and
warranty information. With proper care and consideration, your Water Bee
™ pedal boat will
provide many years of safe, enjoyable, and trouble-free reliability.
For your optimum safety, pleasure, and satisfaction, we urge you to read this manual carefully
and to follow its instructions and recommendations.
Table of Contents
I. Water Bee
II. Tools Required for Assembly…………….….…….……….…………….…...3
III. Assembly Instructions……….…….…..………………………………….…..4
A. Paddle Wheel Blade Installations………………………………………....4
B. Backrest Installation………………………………………………………5
C. Tiller and Rudder Installation………..…………………………………....6
D. Bimini Installation………………………………………………………...7
IV. Maintaining Your Water Bee
A. Checking your Bearings…………………………………………………..9
B. Draining Water from your Water Bee
V. Water Bee
VI. Water Bee
VII. Basic Water Bee Safety..……….……………………………………………13
VIII. Warranty Information………….…….………………………………………14
IX. Warranty Card…………………….…..……………………………………...15
™ Components……….…….…….…………………………………..3
™……………………………………………….…9
™…………………………..………...9
™ Specifications……………..……………………………………...10
™ Technological Aspects…………………………………………...11
Future Beach
™ Corporation
The World’s Beach Company
2
™
Water Bee™ Pedal Boat Owner’s Manual and Assembly Guide
I. Water Bee™ Components
This section will identify your Water Bee
proper terminology for future reference.
Paddle hub Paddle blades Delrin bearings
Threaded Drive Shaft Crankshaft with pedals
™ component parts, and will provide you with the
Steering Arm
Tiller Handle Rudder Rudder Shaft
Storage hatch cover Backrest with clip
II. Tools Required
• 1 set of vice-grips
• 1 set of pliers (optional)
• 1 ratchet (3/4” socket) with extension
• 1 Phillips star screwdriver
Future Beach
The World’s Beach Company
™ Corporation
3
™
Water Bee™ Pedal Boat Owner’s Manual and Assembly Guide
p
b
p
III. Assembly Instructions
A) Paddle Wheel Blade Installation
(Note: for purposes of clarity only, the paddle blade installation (photos 2-5) is
shown without boat)
1. Your paddle hub comes
already installed in your
Water Bee pedal boat. To
access the paddle hub,
simply turn the boat on its
side, or raise the boat onto
a table.
4. Ensure proper
installation of the paddle
lade: listen for the paddle
blade to snap into the
addle hub.
2. Locate open slot on
addle hub and align
base of paddle blade as
shown.
5. Ensuring all paddle blades are installed in
the same direction (think of a swimmer
cupping the water), repeat procedure with
other paddle blades.
Correct paddle blade installation
3. Push paddle blade
firmly into open slot.
Incorrect paddle blade
installation
Future Beach
™ Corporation
The World’s Beach Company
4
™
Water Bee™ Pedal Boat Owner’s Manual and Assembly Guide
p
p
p
B) Backrest installation
1. Your backrest will
come with seat clips
attached to backrest.
2. Using a Phillips star
screwdriver remove
screw and clip from
backrest.
3. Turn backrest over
and repeat previous
rocedure (step 2).
4. Using a flat
screwdriver, pry apart
seat clips from
backrest.
5. Ensuring that backrest is
reclined towards rear of
boat, place backrest
(without clips and screws)
onto adjustment rail as
shown above.
6. Place one seat clip and
screw onto one side of the
backrest (seat clip should
be placed underneath
adjustment rail).
7. Repeat previous
rocedure on other
side of the backrest.
8. Push seat clips firmly
into the backrest with
hands, or with hammer, if
required.
9. Using your Phillips
star screwdriver,
attach seat clip to
backrest tightly.
10. Repeat previous
rocedure on the other
side of the backrest.
11. Swing backrest
towards the center of
12. Install the backrest
into the adjustment
slot of choice
Future Beach
™ Corporation
The World’s Beach Company
5
™
Loading...