EAD
Electric Advance & Drop
Instruction Sheet
Sheet 1 of 8
ISSUE: 003
www.futureautomation.co.uk
1 IR Remote Control
FUNCTION
A remote controlled
mechanism that will
advance and drop a
screen while keeping
it parallel to the wall.
SUITABILITY
SPECIFYING
The wall the mechanism
is to be fixed to must be
completely vertical.
WARNING
It is the responsiblity of
the installer to warn all
potential end users of
the dangers of interfering
with mechanisms during
operation
IMPORTANT
Mechanisms which lift
or move weights need
to be checked on a
yearly basis for any
damage which may
result in an accident
FUTURE
CONTROL
Supplied with basic infrared
remote. Can be learnt
by many learning remotes.
Also has switch control so
can be operated by relays,
switches, Crestron/AMX or
Lutron systems.
AUTOMATION
EAD
Electric Advance & Drop
Instruction Sheet
Sheet 2 of 8
ISSUE: 003
www.futureautomation.co.uk
Fixing to Wall
Always use appropriate
fixing types.
Fitting The Mechanism To The Wall
The EAD must be completely vertical.
Make sure with the use of a spirit level
that the wall behind is vertical. If it is not,
you will have to use washers / spacers
behind the wall plates in order to make
the mechanism completely vertical.
A
Suitability of wall fixings will
depend on the type of
wall the product is to
be fixed to.
If unsure, please seek
instruction from your
supplying dealer.
FUTURE
DETAIL A
AUTOMATION
EAD
Electric Advance & Drop
Instruction Sheet
Checking The Mechanism
Sheet 3 of 8
ISSUE: 003
www.futureautomation.co.uk
Movement
Once fixed to the wall, make
sure the mechanism moves
freely and with ease.
Be sure that the mechanism
cannot sit back against the
wall by itself.
The mechanism operates
by unwinding a long strap
system within the casing.
If the mechnism is leaning
back a lot, the mechansim
may fail to release from
the wall properly.
Make sure the mechanism
CANNOT stay in this position
without motor power or assistance.
FUTURE
AUTOMATION
EAD
Electric Advance & Drop
Instructions Sheet
Adjusting Mechanism Limits
B
DO NOT REMOVE
THIS SCREW
Sheet 4 of 8
ISSUE: 003
www.futureautomation.co.uk
X4 COVER
BOLTS
IN SWITCH
OUT SWITCH
DETAIL B
The EAD comes set to its maximum
drop. Do not try to adjust it past
it's factory setting.
When the buttons are clicked out they are set. To adjust the positions push the buttons so they are clicked in,
use the remote to get mechanism in the new positions. Press stop on the remote in the desired position and
set by pressing the corresponding motor switch so it clicks out. The new position is now set.
FUTURE
AUTOMATION
EAD
Electric Advance & Drop
Instruction
Sheet
Sheet 5 of 8
ISSUE: 003
www.futureautomation.co.uk
Electrical Connections
The EAD
the AC2 connection block.
mechanism must be connected to
Remove this screw to release the lid
Connect the Infrared Sensor here
A
DETAIL A
Connect the IEC Power Lead Here
It is VERY important that when all of the
connector blocks are connected in the
FUTURE
electrical connections are made, the
way shown above, with all the wires
coming directly out the top of the
connector blocks.
AUTOMATION
EAD
Instruction
Electric Advance & Drop
Sheet
Contact Closure
Use an RJ45 connector in the
CC1 socket on the control box
to operate via contact closure.
Sheet 6 of 8
ISSUE: 003
www.futureautomation.co.uk
1
pins
8
There are a number of LEDs
which will light up when the
corresponding contact closure
connections are shorted together.
A red LED will light up when the
emergency stop link is removed.
B
PIN
1
2
3
4
5
6
7
8
568
A
W/G
G
W/O
BL
W/BL
O
W/BR
BR
568
B
W/O
O
W/G
BL
W/BL
G
W/BR
BR
DESCRIPTION
12V SUPPLY CURRENT LIMITED
12V LATCH
GROUND
DEVICE IN LATCHED
DEVICE STOP
DEVICE OUT
DEVICE IN
ACTION
When 12V is attached, device will go OUT.
When 12V is removed, device will go IN.
When shorted to ground, device will go OUT.
When short removed, device will go IN. CC4
When shorted to ground,
stops device in current position. CC3
Momentary short to ground
will make device go OUT. CC2
Momentary short to ground
will make device go IN. CC1
DETAIL B
FUTURE
AUTOMATION
EAD
Instruction
Electric Advance & Drop
Sheet
RS232
Use an RJ11 connector in the
socket marked RS232 on the
control box to operate using RS232.
DETAILS
Band rate: 9600
Stop bit: 1
Parity: None
Databits: 8
PROTOCOL
ASCI
fa_in = Device IN
fa_out = Device OUT
fa_stop = Device STOP
Sheet 7 of 8
ISSUE: 003
www.futureautomation.co.uk
= Carriage Return
PIN 1: IN
PIN 6: OUT
PIN 3&4: GROUND
6
7
1
8
2
3
9
4
5
FUTURE
PIN 2: IN
PIN 3: OUT
PIN 5: GROUND
AUTOMATION
EAD
Instruction
Electric Advance & Drop
Sheet
Operation Details
Sheet 8 of 8
ISSUE: 003
www.futureautomation.co.uk
Contact Closure LEDs
To show the contact closure
operation is working correctly.
LEDs are on when connections
are shorted together.
EMERGENCY STOP
This connection will stop all
functions of the mechanism
once broken / removed. Red
LED will also be on.
AC2
Gives an output of 240V(or 110V)
to control the Electric Tilt motor.
Outputs stay live for 60 seconds
after
the OUT or IN functions are
selected.
FUTURE
AUTOMATION
Loading...