Futaba WTR-7 User Manual

ｎ

G

The

ude

to k

WTR

Th

the RF si

use

W

t

t

th

will

T

the

usua

T

m

7

udent's

.

t

)

)

z

M

G3

W

)

.

t

)

W

7

D

)

pplied

Before using your new WTR-7, please read this manual thoroughly and use the

p

n

t

r

t

T

The LED

WTR

ill be blinki

4

th

ude

The LED

WTR

ill b

Tu

trans

n

d

f

dff

s

f

d

n

trans

WTR

Tu

y

P

.

)

A

d

r

undesired

.

ibl

F

.

T

)

)

:

V

)

)

)

g)

F

4

M

n

20

©

)

)

V

)

pplied

WTR

.

system properly and safely. After reading this manual, store it in a safe place.

ank you for purchasing the WTR-7, Wireless Trainer

ystem for FASST.

e WTR-7 is to be used as a wireless trainer unit instead

f the conventional wired trainer cable.

Wireless

e chart below shows how the WTR-7 is to be used.

Trainer

Syste

TR-

NSTRUCTION MANUAL

Wireless Trainer System

ASST-2.4GHz, FM-PP

M1024 or PCM-

sage condition:

he st

- be in the 7ch mode of FASST such as T6EX, T7C, TM7,

TM8's 7ch-mode, TM10's 7ch-mode, TM14's 7ch-mode, etc.

- have the micro connector trainer port

he instructor's transmitter can be any type of Futaba's

ransmitter which has the micro connector trainer port.

It means that the instructor's transmitter can be FASST,
onventional FM-PPM, PCM1024, or PCM-G3.

WTR-7

transmitter beforehand

Connections and Name of Each Par

(Orange

onnection cord (supplied

For WTR-7 only. Not for other purpose.

lug into the instructor's

transmitter's trainer port.

ini screwdriver (supplied

se the miniature screwdriver su

to operate the Link switch.

elcro tape (supplied

se the Velcro tape su

-7 on the instructor's transmitter

Link switch

TR-

transmitter MUST -

ithin 10m (33ft.

FASST-2.4GH

7ch-mode)

756SHFLÀFDWLRQ

FASST-2.4GHz Wireless Trainer

stem (7ch-mode

Applicable system:

LE

to attach the

ee the paragraph "Usage con

dition".

peration range: 10m

ize: 0.89x1.59x0.52in.

22.5x40.3x13.1mm

Weight: 0.29oz. (8.1

Usage Precaution

WARNIN

instructor and the st



e within 10 meters or 33 ft. in order

eep secure RF link with

ere should not be any people or

ｊ

ther objects between the instructor

nd the student in order to avoid blocking

gnal.

ince the student's transmitter



lso has to be turned on to

TR-7 please make sure that the student's

ransmitter's battery is fully charged or still

as enough capacity to operate for the full

ime of training.

the WTR-7 lose the RF-link with

ｊ

e student's transmitter during the

tudent's control, the priority of the control

automatically back to the instructor

egardless of the instructor's selector.

herefore, please keep paying attention to

model as

l.

nt must

-7.

the

AUTION

he connection cable is specially



ade for the WTR-7 thus it MUST not

e used for any other purpose.

eration Ste

reparatio

e sure that the student's transmitter is on FASST

7ch-mode if it's selectable.

• For utilizing the T14MZ or T12Z as the student.
ease set the trainer mode to "Teacher" in order

o get power to the WTR-7 for linking.

ink to the student's transmitte

Plug the WTR-7 into the student's

ransmitter's trainer port.

urn on the student's transmitter.

on the

.

Press and hold the link switch for more

an 2 seconds in order to link to the

t

nt's transmitter.

akuhari Techno Garden Bldg., B6F 1-3 Nakase, Mihama-ku, Chiba 261-8555, Japa

M23N174

-7 w

UTABA CORPORATION Phone: [phone] Facsimile: [phone]

ng

on the

-7 w

e on green

olid when the link is established.

rn off the transmitter.

nplug the WTR-7 from the student's

mitter.

ED Indicatio

reen

oli

link alternatelynrecoverable failure (EEPROM, etc.)

e

f

olid

o signal reception

eceiving signal

f

eceiving signals but ID is unmatche

tatus

Trainer function operatio

lug the WTR-7 to the instructor's

mitter.

x the
transmitter in order to prevent it from becoming
unplugged and dropping off the transmitter.

Check the airplane's control surfaces to

make sure

ther settings for the trainer usage are same as the

onventional usage.

lease refer the transmitter's instruction manual

r detail

ompliance Information Statement

for U.S.A.

This device, trade name Futaba Corporation of

merica, model number WTR-7, complies with
part15 of the FCC Rules. Operation is subject to the
following two conditions:

1)This device may not cause harmful interference, an

2) This device must accept any interference
eceived, including interference that may cause

The respons

utaba Service Center
002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A
EL [phone] or E-mail: [e-mail] (Support

TEL [phone] or E-mail: [e-mail] (Service

-7 to some place on the instructor's

rn on both transmitters.

ou have proper operation.

operation

e party of this device compliance is:

FUTABA CORPORATION 2009, 07 (1