Futaba
DIGITAL PROPORTIONAL
RADIO CONTROL
FM
D60399
Thank you for purchasing a Futaba digital proportional radio control set.
Please read this manual carefully before using your set.
FEATURES OF FP-6NLK/5NLK
The FP-6NLK and FP-5NLK are 6 channel (6NLK) and 5
channel (5NLK) FM proportional radio control set with a
ergonomic case created as a result of the exhaustive pursuit
of easier operation, newly designed sticks tor smooth and
positive operation, servo reversing switch for each channel,
and other innovations based on the opinions and needs of
many RC modelers.
Please read this manual before using your new set.
TRANSMITTER FP-T6NLK/T5NLK
• Reliability substantially improved by using industrial robots
to assemble the PC board.
• Servo reversing switch for each channel. Servos are reversed
by using this switch.
• Newly designed open gimbal sticks operate smoothly and
positively.
Spring tension mechanism
allows adjustment of the operat-
ing
feel of the stick lever.
•Nonslip
adjustable
lever
head allows adjustment
of
the stick
length as desired.
• RF PC board module style system in transmitter. (Internal
only)
• Functional case, created as a result of the exhaustive pursuit
of
easier
operation,
has
evolved a thick
case
which
fits
into
the palm of the hand.
•Aileron, Elevator dual rate function. (Dual rate ON, OFF)
• Easy to read square transmitter battery voltage/output level
meter.
• Excellent radiation efficiency, strong 8-stage telescoping
antenna.
• Neck strap bracket provided as standard. Operation is easier
if the transmitter is hung from your neck by using the
optional neck strap.
• Large capacitor copes with voltage changes when a battery is
used.
• Vibration-resistant pin connectors.
• Fiberglass epoxy PC board with thru-the-hole plating is vibration and shock resistant.
SERVO FP-S138
SMALL, RUGGED, HIGH NEUTRAL LOW PROFILE SERVO
• Height is 0.2 in (5.2mm) lower than existing servos of its
type.
• New indirect drive potentiometer improves vibration
and
shock resistance and neutral accuracy.
• Futaba low-power custom 1C provides extremely high
torque, narrow dead band, and superior tracking.
• Fiberglass reinforced PBT (polybutylene terephthalate)
injection molded servo case is mechanically strong and
invulnerable to glow fuel.
• Strong polyacetal resin ultra-precision servo gear features
smooth operation, positive neutral, and very little backlash.
• Fiberglass reinforced epoxy resin PC board with thru-the-
hole plating improves servo amp vibration and shock resistance.
•Three pin connector eliminates faulty contact and improves
reliability against vibration and
shock. Housing has a reverse
insertion prevention mechanism.
•Special grommet simplifies mounting of the servo and has
an excellent cushioning effect.
• Six special adjustable splined
horns.
• Since the output torque is 34.75oz-in (2.5kg.cm) and operating speed is 0.23sec/6CT, it can be used with almost all
models.
RECEIVER FP-R107N
• Compact, high performance FM 7-channel receiver with PC
board space reduced to a minimum.
•Special IF amp for radio communications improves the
effective receiving range stability.
•Narrow band ceramic filter improves rejection of adjacent
channel interference.
• Futaba original squelch circuit reduces erroneous operation
by
weak
signals
(when
passing a dead
point,
etc.)
and
erroneous operation by natural noise when no signals are being
received.
SET CONTENTS AND RATINGS
(Specifications are subject to change without prior notice.)
Transmitter
Receiver
Servo
Battery holder
Switch
Others
FP-6NLK
FP-T6NLK x 1
FP-R107N x 1
FP-S138x4
NR-4J x 1
SSW-J x 1
Charger, Frequency flag. Spare horn,
Mounting screw.
FP-5NLK
FP-T5NLK x 1
FP-R107N x 1
FP-S138x4
TRANSMITTER FP-T6NLK/T5N
Operating system : 2 stick, servo reverse
Aileron, Elevator dual
switch,
Landing gear switch (5ch)
[Switch (6ch) 6NLK only
Transmitting frequency : 53, 72MHz bands
Modulation system : FM
Power requirement : 9.6V NiCd battery
(NT-8LP)
Current drain : 190mA
RECEIVER FP-R107N SERVO FP-S138
Receiving frequency : 53, 72MHz bands Control system +pulse width control
Intermediate frequency : 455kHz Operating angle One side 45° or more
Power requirement : 4.8V NiCd battery (including trim)
(Common use with servo) Power requirement 4.8V~6V
Current drain : 13.5mA (4.8V reception) Current drain (IDLE) 6.0V, 8mA
Dimensions : 1.38 x 2.42 x 0.8 in Output torque 34.75oz-in (2.5kg-cm)
(35.2x61.7x20.3mm) Operating speed 0.23 sec/60°
Weight : 1.55oz (43g) Dimensions 1.59 x 0.79 x 1.38 in
Receiving range : 550 yards (500m) on the (40.5 x 20 x 35.3mm)
ground, 1,100 yards
Weight
1.44oz(41g)
(1,000m) in the air.
(at the best conditions)
TRANSMITTER FP-T6NLK/T5N CONTROLS
Fig. 1 shows the name of each part of the transmitter.
Memorize the position and operation of each
switch and control.
Elevator dual trimmer
Landing gear switch
Antenna
Handle
Aileron dual trimmer
6th CH switch (6NLK only)
Aileron dual switch
Neck strap
bracket
Elevator
trim lever
Aileron
trim
lever
Charging
jack
Power switch
Rudder
Throttle
Transmitter
NiCad battery
NT-8LP
Aileron
Elevator
Nonslip adjustable
lever head
Fig.1
Battery cover
Servo reversing
switches
Rudder
trim lever
Throttle trim
lever
Level meter
In the following descriptions, all the servo reversing switches
are assumed to be in the normal position. When they are in the
reverse position, operation is the opposite of that described.
®
Aileron
Aileron operation
Elevator
Elevator operation
Throttle
Throttle operation
Rudder
Rudder operation
Landing gear switch
Raising and lowering the
landing gear.
6th CH switch (6NLK only)
Use for controlling model
airplane flaps, etc. The
servo is operated at the
and positions. The
The servo is connected
to 6 channels. Fig. 2
position is off.
Aileron trim lever
Elevator trim lever
Throttle trim lever
Rudder trim lever
Aileron trimmer
Elevator trimmer
Throttle trimmer
Rudder trimmer
Aileron dual rate switch
Aileron dual rate ON-OFF switch. When set to the upper
position, dual rate is turned on, and when set to the lower
position, dual rate is turned off.
Aileron dual rate trimmer
This trimmer sets the aileron travel when the aileron dual
rate switch is set to on. When the dual rate switch is set to
ON, the servo throw can be set to an arbitrary angle smaller than when the dual rate switch is OFF (normal) as
shown in the figure. Use the throw matched to the aircraft
and the maneuvers to be performed.
throw can be adjusted within this range with the dual rate trimmer.
When the dual rate switch is ON, the servo
Fig.
3
OFF
100%
Dual rate switch
Loading...