Futaba FP-S126G, FP-S16G INSTRUCTION MANUAL
Futaba
FP-S126G
FP-S16G
-
SMALL,
These small, rugged landing gear servos are designed for use with Futaba radio
control sets. The FP-S126G is for the Futaba J Series and the FP-S26G is for
the FN. G, and L Series.
[FEATURES]
* Clockwise and counterclockwise rotation is controlled by the magnitude of
the pulse width by ON-OFF of the transmitter snap switch and is stopped
at the end of the stroke.
* Since motor drive current does not flow when stopped even when a small
load is applied, current drain is low.
*
Thick
film
metal
plated connector
reliability against vibration and shock.
*Polybutylene terephtalate fiberglass case is rugged and invulnerable to fuel.
for J Series
for
FN,
RUGGED,
pins
G,
LANDING
eliminate faulty
L
Series
GEAR
contact
SERVOS
and
increase
[RATINGS]
Control system : + pulse width control
Operating angle : 160° or greater
Power requirement : 4.8V or 6.0V(shared
Current drain : 6.0V, 8mA (at idle)
Output torque : 58.4oz/in(4.2Kg -cm)
Operating speed : 0.30sec/60°
Dimensions : 1.56X0.75X1.56inch(40.5X20X40-5m/m)
Weight : 1.7oz(46g)
[USAGE PRECAUTIONS]
* Use the FP-S126G with a J series digital proportional set.
* Use the FP-S26G with an FN, G, or L Series digital proportional set.
Futaba servos can not be used with other makes of RC sets.
* Match the landing gear stroke with the stroke of the landing gear servo.
Link the servo to the landing gear so that pulling and pushing are neither
excessive nor insufficient.
* When mounting the servo with screws, always use bushings. Tighten the
screws until the bushing is slightly crushed. The shock absorbing effect
will be lost if the screws are too tight.
* A spare horn is supplied. Use is as needed.
(Specifications are subject to change without prior notice.)
with receiver)
Part
No.
1
Upper case
2
Middle case
3
Bottom case
4
Motor
5
Motor pinion
6
Phillips pan head screw 2X3
7
1st gear
8
2nd gear
9
3rd gear
10
Final gear
11
Intermediate shaft
12
2nd shaft
13
Output shaft
14
Washer
15
Push nut 1.50
16
Metal slider
17
TR13 VR145D
18
Fiber washer
19
Iron truss screw 2x4
20
Servo horn G
21
2o toothed washer
22
Binding head tapping screw 2X8
23
Neoseal spong 5x15X15
24
Neoseal spong 3X15X7
25
Printed wiring board
S126------3PB-WRB300
2
6
S26
••••••with
27
Iron pan head screw 2X35
28
Nameplate
Name
3PC
cord
Part
No.
S05600
S05620
S05460
S91212
S02461
J50002?
S02490
S02491
S02715
S02716
S02495
S02494
S02803
S11043
J60070
i 40002
i 39999
S90332
J52012
S01220
J20100
J55023
S90336
S90333
AS1200
FPC-8M
FPC-5M
J50400
S80669
FUTABA CORPORATION OF AMERICA
555 West Victoria Street Compton, California 90220 U.S.A.
Phone : (213)
537-9610
Telex : 23-0691227 Facsimile : 213-637-8529
FUTABA CORPORATION
Tokyo
Office:
Phone : (03) 255-5881 Telex : J26532
DAIDO
BLDG.,
Tokyo, Japan.
3-1-16.
Sotokanda,
Chiyoda-ku.
Loading...