Fusion by GLP Exo Wash 30 Moving Head User Manual [EN]

User Manual

Software version V1.0.00

Fusion EXO Wash 30

GLP® Fusion EXO Wash User Manual – Revision B

This document covers fixture software version V1.0.00

© 2019 German Light Products GmbH. All rights reserved.

The marks ‘GLP’ and ‘German Light Products’ are trademarks registered as the property of German
Light Products GmbH in Germany, in the United States of America and in other countries.

The information contained in this document is subject to change without notice. German Light
Products GmbH and all affiliated companies disclaim liability for any injury, damage, direct or
indirect loss, consequential or economic loss or any other loss occasioned by the use of, inability to
use or reliance on the information contained in this document.

Manufacturer’s head office:
German Light Products GmbH (GLP), Industriestrasse 2, 76307 Karlsbad, Germany
Tel (Germany): [phone] - 0

Service & Support EMEA:
GLP, Industriestrasse 2, 76307 Karlsbad, Germany
Tel. (Germany): [phone]
Email: [e-mail]
www.glp.de

Service & Support USA:
GLP USA, 1145 Arroyo St., Ste. A, 91340 San Fernando, California
Tel (USA): [phone]
Support (US): [e-mail]
www.germanlightproducts.com

Table of Contents

1. Safety .......................................................................................................... 5

Key to symbols ...................................................................................... 5

General safety information ................................................................. 5

Electrical safety .................................................................................... 6

Fire safety and protection from burns ................................................ 7

Eye safety .............................................................................................. 8

Strobe safety ......................................................................................... 8

Installation safety and protection from personal injury ................... 9

2. Avoiding damage to the fixture ............................................................ 10

General precautions .......................................................................... 10

Avoiding damage from light sources and heat ............................. 10

IP rating ................................................................................................ 11

Avoiding damage from water and humidity .................................. 11

Avoiding damage from dust and airborne particles ..................... 12

Transportation and storage ............................................................... 12

GLP Service and Support ................................................................... 12

3. EXO Wash 30 overview ........................................................................... 13

4. Installation ................................................................................................. 15

Permitted mounting options ............................................................. 15

Securing fixtures with a safety cable ............................................... 15

Installing on a rigging truss or similar structure ................................. 16

Standing on a horizontal surface ..................................................... 17

5. AC mains power ...................................................................................... 18

Included items .................................................................................... 18

Connecting to power ........................................................................ 18

Installing power connectors .............................................................. 19

Connecting multiple fixtures to power in a chain .......................... 19

6. Connecting to DMX data ....................................................................... 20

7. Starting and stopping operation ........................................................... 21

8. Features .................................................................................................... 22

Position ................................................................................................. 22

Color .................................................................................................... 22

.............................................................................................................. 22

Dimming .............................................................................................. 23

Strobe / shutter ................................................................................... 23

Zoom .................................................................................................... 23

Behavior when the fixture is not receiving a DMX signal ............... 23

9. Control menus and onboard display .................................................... 24

Display options .................................................................................... 25

Display Locking ................................................................................... 25

Manual Control ................................................................................... 25

LED PWM frequency ........................................................................... 25

Fan control .......................................................................................... 25

Fixture information .............................................................................. 25

Pan disable / Tilt disable .................................................................... 26

Preset settings and factory defaults ................................................. 26

10. Control menu layout ............................................................................... 27

Service Advanced menu .................................................................. 29

11. DMX control modes overview ................................................................ 30

12. DMX control channel layout tables ....................................................... 33

DMX Mode 1: Compact .................................................................... 33

DMX Mode 2: Standard ..................................................................... 35

DMX Mode 3: Extended .................................................................... 39

13. Service ...................................................................................................... 48

Cleaning .............................................................................................. 48

GLP Service and Support ................................................................... 48

14. Technical specifications ......................................................................... 49

Optics ................................................................................................... 49

Control ................................................................................................. 49

Installation ........................................................................................... 49

Electrical .............................................................................................. 49

Connections ........................................................................................ 49

Construction ........................................................................................ 49

Thermal ................................................................................................ 49

Included items .................................................................................... 50

Dimensions and weight ..................................................................... 50

15. Dimensions ................................................................................................ 51

German Light Products® Safety

Warning! Safety hazard.
Risk of severe injury or
death.

Warning! Hazardous voltage.
Risk of lethal or severe
electric shock.

Warning! See user
manual for important
safety information.

Warning! Fire hazard.

Warning! Risk of eye
injury.

1. Safety

Key to symbols

The following symbols are used in the Fusion EXO Wash 30 lighting fixture’s user
documentation:

General safety information

Read this manual carefully before installing, using or servicing the Fusion EXO Wash 30
lighting fixture.

If you have any doubts or questions about how to use the fixture safely, contact your
GLP® supplier for assistance. Your GLP supplier will be happy to help.

The user documentation for GLP Fusion EXO Wash 30 lighting fixtures consists of:

● This document, the EXO Wash 30 User Manual, supplied with the fixture and
available for download from www.glp.de. The User Manual contains important
safety information and installation instructions that the installer and user must read.

● The EXO Wash 30 DMX Channel Index, available for download from www.glp.de.
The Channel Index is a separate guide to the DMX control channel layout and DMX
commands available.

All documents are available for download from www.glp.de.
The Fusion EXO Wash 30 is intended for use by experienced professionals with the

knowledge and skills to set up, operate, and maintain high-powered, remotely
controlled lighting equipment safely and efficiently. These operations require expertise
that may not be provided in this Manual or in the User Manual.

● Respect all warnings and directions given in the fixture’s user documentation and
on the fixture. Read the user documentation and familiarize yourself with the safety
precautions it contains before installing or using the fixture. GLP and affiliated

EXO Wash 30 User Manual Rev. B 5

www.glp.de Safety

companies will take no responsibility for damage or injury resulting from disregard for
the information in the user documentation.

● Check the GLP website at www.glp.de and make sure that you have the latest
version of this manual. Check the fixture software version indicated on page 2 of this
manual and then use the fixture’s control panel to check the version installed in the
fixture. If the versions are not the same, this manual may still cover the fixture,
because software updates do not always affect the way you use the fixture.
However, it is possible that this manual does not match the fixture perfectly.
Software release notes can help clarify this question. You can consult software
release notes and download the correct version of this manual on the GLP website if
necessary.

● Make all user documentation available to all installers and operators. Save this
document for future reference.

● If you have any questions about the safe operation of the fixture, please contact an
authorized GLP distributor (see list of distributors at www.glp.de).

● Use the fixture only as directed in this manual. Observe all markings in this manual
and on the fixture.

● Refer all repairs and any service operation not described in this manual to a
technician authorized by GLP.

● The light source in this fixture must not be changed by the end user.

● Read and follow the user documentation for all additional equipment.

Electrical safety

● Do not allow the fixture to become immersed. Do not expose the fixture to high­pressure water projections.

● Keep any unused connectors on the fixture sealed with their protective caps at all
times, both when the fixture is in use and when not in use.

● Use only a source of AC mains power that complies with local building and
electrical codes and has both overload and ground fault (earth fault) protection.

● Ensure that the fixture is electrically connected to ground (earth).

● Disconnect the fixture from AC mains power before carrying out any installation or

maintenance work and when the fixture is not in use.

● Disconnect the fixture from power immediately if any seal, cover, cable, connector
or other component is damaged, defective, deformed or showing signs of
overheating. Do not reapply power until the fixture has been repaired and made
safe by a technician authorized by GLP.

● Check that all power distribution equipment, cables and connectors are in perfect
condition, rated for the electrical requirements of all connected devices, suitable
for their application and suitable for the installation environment.

6 EXO Wash User Manual Rev. B

German Light Products® Safety

● Use only Neutrik PowerCON TRUE1 cable connectors for AC mains power input at
the fixture’s Mains IN connector and for relaying AC mains power from one fixture’s
Mains OUT (Thru) connector to another fixture’s Mains IN connector.

● Use minimum 14 AWG or 1.5 mm2 power input and relay cables that are minimum
16 A-rated and temperature-rated to suit the application. In the USA and Canada
the cables must be UL-listed, type SJT or equivalent. In the EU the cables must be
type H05VV-F or equivalent.

● Do not connect devices to power in a chain if the total maximum current draw of all
the devices in the chain when added together will exceed the current rating of any
cable or connector used at any point in the chain. The supplied power input cable
is rated as follows:

- US power cable: 16 A, 14 AWG, UL-listed, E304117, SJT, 4.9 ft.

- EU power cable: 16 A, 1.5 mm², H07RN-F, 1.5 m.

Do not connect more than four (4) Fusion EXO Wash 30 fixtures to power in a chain at
100-120 V, 60 Hz.

Do not connect more than eight (8) Fusion EXO Wash 30 fixtures to power in a chain
at 200-240 V, 50 Hz.

● The voltage and frequency at the Mains OUT socket are the same as the voltage
and frequency applied to the Mains IN socket. Only connect devices to the Mains
Out socket that accept this voltage and frequency.

● Fusion EXO Wash 30 fixtures do not have a user-replaceable fuse. If you suspect that
a fuse has blown, disconnect the fixture from power and send it to a technician
authorized by GLP for repair.

Fire safety and protection from burns

● Do not operate the fixture if the ambient temperature (Ta) exceeds 40° C / 104° F.

● The surface of the fixture’s casing can reach up to 90° C / 194° F during operation.

Avoid contact by persons and materials. Do not install the fixture in a location where
there is a risk of accidental contact. Allow the fixture to cool for at least 20 minutes
before handling

● Keep the fixture well away from flammable materials.

● Keep all combustible materials (e.g. fabric, wood, paper) at least 0.5 m / 20 in.

away from the fixture.

● Ensure that there is free and unobstructed airflow around the fixture.

● Do not illuminate surfaces within 0.5 m / 20 in. of the fixture. The light output from the

fixture is powerful enough to cause burns or fire in illuminated objects at very close
range.

● Do not stick filters, masks or other materials onto the fixture. Do not block the light
output in any way. The front surface becomes hot during operation and can melt or

EXO Wash 30 User Manual Rev. B 7

www.glp.de Safety

ignite objects that are in contact with the surface. Ensure that the front surface Is
clean and unobstructed at all times in order to prevent a fire hazard and damage
to the fixture.

● The fixture’s optical components can focus the sun’s rays, creating a risk of fire and
damage. Do not expose the front of the fixture to sunlight or any other intense light
source, even from an angle.

Eye safety

● The EXO Wash 30 is classified as a Risk Group 3 lighting fixture according to EN 62471.
Possibly hazardous radiation emitted. Do not stare into the light output from the
fixture. May be harmful to the eyes.

● Do not look at the fixture’s light output with optical instruments or any device that
may concentrate the light output.

● Make sure that persons near to or working on the fixture are not looking directly into
the light output when the fixture lights up suddenly. This can happen when power is
applied, when the fixture receives a DMX signal, or when certain control menu items
are selected.

● The warning below is printed on the fixture. If the warning becomes impossible to
read, replace it with a label reproduced from this illustration:

● Provide well-lit conditions to reduce the pupil diameter of anyone working on or
near the fixture.

Strobe safety

● Flashing light, particularly at 5 - 30 Hz, may cause seizures in persons with
photosensitive epilepsy. Do not use strobe effects for extended periods.

● Comply with local regulations on the use of strobe lighting and notify the public in
advance with highly visible warning signs when strobe effects are used.

● If a seizure occurs, stop using strobe effects. Seek professional medical help. Note
the time that the seizure starts and finishes. Call emergency medical help urgently if

8 EXO Wash User Manual Rev. B

German Light Products® Safety

the seizure lasts more than five minutes, if it is the person’s first seizure, or if the person
is injured. While waiting for help to arrive, protect the affected person from injuring
themselves on hard or sharp objects. If necessary, move the person to a safe place.
Lay them on their side with their head supported to prevent it from hitting the floor.
Loosen any tight clothing around their neck. Do not use force to hold the person or
restrict their movements. Do not put anything in their mouth, including your fingers.

Installation safety and protection from personal injury

● Installation must be performed by qualified personnel only and carried out in
accordance with all locally applicable regulations such as DIN VDE 0711-217.

● The fixture is not portable when installed.

● Ensure that the supporting structure and installation hardware used can hold at least

ten times the weight of the load that they support.

● Fasten the fixture to a structure or surface only as directed in this manual and only
with hardware that is specifically designed and rated for its purpose. Do not use a
safety cable as the primary means of support. Check that installation hardware is in
perfect condition. Fasteners must be steel grade 8.8 strength or better. Rigging
clamps must be half-coupler type that completely encircle the rigging truss chord.

● If the fixture is installed in a location where it may cause injury or damage if it falls,
install as directed in this manual a safety cable or similar secondary attachment that
will hold the fixture if a primary attachment fails. The secondary attachment must be
approved by an official body such as TÜV as a safety attachment for the weight
that it secures, it must comply with EN 60598-2-17 Section 17.6.6, and it must be able
to support a static suspended load that is ten times the weight that it secures.

● If the fixture is installed in a location where it may be exposed to forces such as wind
pressure, vibration or movement, make sure that the installation can withstand these
forces. Monitor weather forecasts constantly. Take down the installation
immediately if there is any risk of weather conditions that could destabilize the
installation.

● Check that all covers and items of rigging hardware are secure before using the
fixture. Do not operate the fixture with missing or damaged covers, shields or any
optical component.

● Restrict access below the work area and work from a stable platform whenever
installing, servicing or moving the fixture.

● If the fixture becomes damaged, stop using it immediately and disconnect it from
power. Do not attempt to use a fixture that is obviously damaged.

● Do not modify the fixture in any way not described in its user documentation.

● Install genuine GLP parts only.

EXO Wash 30 User Manual Rev. B 9

www.glp.de Avoiding damage to the fixture

2. Avoiding damage to the fixture

Important! Follow the directions in this section carefully, or the fixture may suffer
damage that is not covered by the product warranty.

General precautions

Do not drop the fixture or expose it to mechanical stress.
Protect the onboard LCD display and control panel from shocks, or they may suffer

damage that is not covered by the product warranty.
Do not expose the fixture to heat (from other lighting fixtures for example).

Clean optical components only as directed. Oils, solvents, and other chemicals
commonly used for cleaning can damage the lens coatings and surfaces.

Use only original spare parts. Do not make any structural modifications to the fixture or
you will void the product warranty.

Avoiding damage from light sources and heat

Do not point the front of the fixture towards the sun or other strong light sources. Strong
light can cause internal damage to the fixture, melting components or starting an
internal fire within seconds.

Figure 1. Avoiding damage from light sources

Damage can occur whether the fixture is powered on or off. See Figure 1. Damage
can also occur if the light hits the front of the fixture at an angle: the fixture does not
need to be pointing directly at the sun or other light source.

To avoid problems from strong light sources:

● Do not expose the front of the fixture to sunlight or any other strong light source.

● In outdoor applications during daylight, make sure that the front face of the fixture is

shielded or points away from the sun, even when not in use.

● Do not aim other high-powered beam lights directly at the fixture.

Do not operate the fixture in ambient temperatures above 40° C / 104° F. Allow free
airflow around the fixture.

10 EXO Wash User Manual Rev. B

German Light Products® Avoiding damage to the fixture

IP rating

EXO Wash 30 fixtures are IP65-rated:

● IP stands for Ingress (entry into the fixture) Protection.

● The first figure 6 in the rating means that fixtures are protected against the entry of

dust and airborne particles.

● The second figure 5 in the rating means that fixtures are protected against the entry
of rain and water projections from all angles. Fixtures are not protected against
immersion in water and they are not protected against high-pressure water jets.

Avoiding damage from water and humidity

● Do not install EXO Wash 30 fixtures in a location where water can pool around the
fixture or allow EXO Wash 30 fixtures to become submerged in any other way. Do
not aim low- or high-pressure water jets at fixtures.

● Keep all unused connectors on the fixture sealed with their protective caps, both
when the fixture is being used and when it is not in use.

● In outdoor and high-humidity environments, use IP65-rated power and data
connectors and cable (an IP65 rating means that the item is protected against the
entry of water from rain, projections and low-pressure jets as well as the entry of
dust). When assembling connectors and installing them on cable, follow the
manufacturer’s instructions (see www.neutrik.com) and ensure that an IP65 rating is
maintained for the complete assembly. Use only the following cable connectors:

- IP65-rated 5-pin XLR connectors for data IN and OUT (THRU)

- Neutrik powerCON TRUE1 NAC3FX-W for Power IN

- Neutrik powerCON TRUE1 NAC3MX-W for Power OUT (THRU).

● Apply a dielectric grease (available from electrical suppliers) to connector terminals

and caps to prevent corrosion and/or electrical short circuits.

● Make sure that cables open into dry areas or sealed junction boxes. Moisture can
be drawn along cables by capillary action or pressure variations resulting from
thermal expansion.

● See drawing on right.
Arrange cables so that they
arrive at connectors from
below. Make sure that it is
impossible for water to flow
down cables and
accumulate at connectors.
If necessary, provide extra
cable slack and create ‘drip loops’ before connectors.

● Create loose cable bends only. Do not subject connections to bending forces or
allow connections to bear the weight of long lengths of cable.

EXO Wash 30 User Manual Rev. B 11

www.glp.de Avoiding damage to the fixture

Avoiding damage from dust and airborne particles

● Carry out regular visual inspections of the fixture to make sure that there is no
accumulation of dirt, especially on the front of the fixture.

● If cleaning is necessary, follow the instructions in ‘Service’ on page 48.

Transportation and storage

● Transport the fixture in its original packaging or a suitably designed flight case to
protect it from damage caused by shocks during transportation.

● Release the tilt lock and support the fixture’s head with the original packaging
inserts or flight case inserts during transportation.

● Store the fixture in a dry location when not in use.

GLP Service and Support

Contact information for the nearest GLP Service and Support is available online at
www.glp.de/en/service, by email at [e-mail], or by telephone at the following
numbers:

● GLP Germany: [phone]

● GLP N. America: [phone]

● GLP UK: [phone]

● GLP Asia: [phone]

● GLP Nordic: [phone]

12 EXO Wash User Manual Rev. B

German Light Products® EXO Wash 30 overview

3. EXO Wash 30 overview

The Fusion EXO Wash 30 from GLP is a powerful LED-based wash light fixture with fast
pan and tilt, 4 to 54 degree variable zoom and seven independently controllable
RGBW zones.

The fixture can be controlled by DMX or by settings on its built in color LCD control
panel. An optional wireless DMX module can be fitted to enable LumenRadio wireless
control. The fixture has a built-in battery to allow the display to be operated for setup
before mains power is connected.

The EXO Wash 30 can be used indoors in permanent and temporary installations. Its
rugged construction and IP65 rating mean that it can also be used outdoors in
temporary installations if precautions are taken to prevent immersion in water and
damage from direct sunlight. It can stand on a horizontal surface or be suspended
from a suitable structure as described in Section 4.

The EXO Wash 30 is not suitable for household use, for use in any location where
unattended children have access to it, or for use in permanent outdoor installations.

EXO Wash 30 User Manual Rev. B 13

www.glp.de EXO Wash 30 overview

8 – Wireless indicator

9 – Battery button

10 – PowerCON TRUE1 input

11 – Mode / Esc button

12 – Up button

13 – Down button

14 – Enter button

15 – Optional wireless antenna

16 – 5 pin XLR DMX input

17 – 5 pin XLR DMX link out

18 – Vent valve

19 – PowerCON TRUE1 link out

1 – Output lens

2 – Head

3 – Tilt lock

4 – Yoke

5 – Base

6 – Control panel

7 – Rubber feet

Figure 2. EXO Wash 30 overview

14 EXO Wash User Manual Rev. B

German Light Products® Installation

4. Installation

Warning! Read ‘Safety’ starting on page 5 for important safety information
that you must understand before you install or operate the fixture. Install
EXO Wash 30 fixtures only as described in this chapter, or you may create an
installation that is unsafe.

Install the fixture at least 0.5 m / 20 in. away from combustible materials
(wood, textiles, paper, etc.), 0.5 m / 20 in. away from any surface that will
be illuminated, and a safe distance away from any flammable materials
(volatile spirits, etc.).

It is the installer’s responsibility to provide a stable, secure supporting
structure that is suitable for the environment and application and that
meets all applicable codes and legal requirements. Note the requirement
to secure lighting fixtures with safety cables in temporary installations.

Permitted mounting options

An EXO Wash 30 fixture may be installed in one of the following ways:

1. Fastened to a rigging truss or similar structure at any angle by means of
truss couplers or other clamps fixed to the two Omega brackets which attach
to the half-turn couplers on the underside of the base.

2. Standing upright on the base on a horizontal surface.

Securing fixtures with a safety cable

In temporary installations, if a fixture can cause injury or damage if it falls you must
secure it with a secondary attachment such as a safety cable that will hold it if the
primary means of attachment fails. The safety cable must be approved for the weight
that it secures. In multiple installations, each fixture must have its own safety cable.

EXO Wash 30 User Manual Rev. B 15

www.glp.de Installation

To secure an EXO Wash 30 fixture with a safety cable:

Figure 3. Safety cable attachment

1. Loop a safety cable around a secure anchoring point such as a truss
beam or fixed structure so that it will catch the fixture if a rigging clamp fails.
Take up as much slack as possible in the safety cable (by looping it more than
once around the bar, for example).

2. See Figure 3 and Figure 4. Fasten the safety cable through the slot “B” on
the underside of the fixture base. Check that the fixture is now secured.

Installing on a rigging truss or similar structure

You can suspend an EXO Wash 30 fixture from a rigging truss or pipe using suitable
clamps attached to the Omega Brackets supplied with the EXO Wash 30.

If you are going to install the fixture hanging vertically downwards from a horizontal
rigging truss or pipe, you can fasten it to the truss using G-clamps. If you are going to
install the fixture in any other orientation, you must use half-coupler clamps that
completely surround the truss chord or pipe.

16 EXO Wash User Manual Rev. B

German Light Products® Installation

Figure 4. Omega bracket fasteners

1. Attach suitable clamps to the Omega brackets.

2. Line up the fasteners of the Omega bracket with the holes “A” in the
base of the EXO Wash 30 as shown in Figure 4. The brackets may be installed
either way round so the cabling is in line with the bar or at right angles to it.

3. Lock the Omega brackets onto the EXO Wash 30 by turning the fasteners
through 90 degrees.

4. Attach the clamp to the truss or structure. Ensure that the head and yoke
of the fixture will not collide with any fixed objects as the fixture moves. Ensure
that the fixture has sufficient clearance to any adjacent surfaces or objects.

5. Secure the fixture with a safety cable through slots “B” as described in the
previous section.

Standing on a horizontal surface

To install an EXO Wash 30 fixture on a horizontal surface:

1. Check that the surface is secure and can safely hold the weight of the
fixture plus all hardware and cables.

2. Stand the fixture firmly on the rubber feet fitted to the base of the unit.
Ensure that the head and yoke of the fixture will not collide with any fixed
objects as the fixture moves. Ensure that the fixture has sufficient clearance to
any adjacent surfaces or objects.

EXO Wash 30 User Manual Rev. B 17

www.glp.de AC mains power

5. AC mains power

Warning! Read ‘Safety’ starting on page 5 for important safety information
that you must understand before you install or operate the fixture.

Check that all cables and connectors are suitable for the installation
environment and application (see recommendations in ‘Avoiding damage
to the fixture’ on page 10).

Use H07 RN-F 3 x 2.5mm / SJT 12 AWG cables with original Neutrik powerCON
TRUE1 connectors to supply power to fixtures.

Line up the keyways in connectors carefully. Do not try to insert or twist a
connector if it feels excessively stiff. Resistance to insertion or twisting is a sign
that connectors may be incorrectly lined up.

Keep connectors sealed with their rubber caps at all times when not in use.

Included items

The EXO Wash 30 is supplied with a power cord with Neutrik powerCON TRUE1
connector.

Connecting to power

The AC mains power supply must include a connection to ground / protective earth. It
must be protected against ground / earth leakage and overload. The fixture’s internal
auto-sensing power supply accepts AC power at 100-240 V, 50/60 Hz. Do not connect
the fixture to power at any other voltage or to an external dimmer.

The EXO Wash 30 does not have a power ON/OFF switch. Power is applied to the
fixture as soon as the power cable becomes live.

The EXO Wash 30 has a 3-conductor Neutrik powerCON TRUE1 Mains IN power input
socket that accepts AC power from a TRUE1 female cable connector. Although TRUE1
connectors support hot plugging, it is still good practice to shut down power to power
cables before connecting them to fixtures.

To connect the fixture to power:

1. If convenient, shut down power to the power input cable.

2. Note the position of the keys and keyways on the TRUE1 power cable
connector and Mains IN socket and align them with each other. Insert the
cable connector into the socket and twist clockwise to lock. Do not use force.
If the connector feels excessively stiff, remove it and check again that it is
lined up correctly.

3. Before applying power to the power cable, check that nobody is looking
directly into the front of the fixture.

To disconnect the fixture from power, pull the latch on the cable connector outwards
to release it, then twist the connector counterclockwise and pull to remove it from the
socket.

18 EXO Wash User Manual Rev. B

German Light Products® AC mains power

Live or L

Neutral or N

Ground / Earth or

US system

Black

White

Green

EU system

Brown

Blue

Yellow/green

Installing power connectors

If you intend to draw power from convenience receptacles / consumer mains power
sockets, it is possible to install a suitable cord cap / power plug on the supplied power
cord / input cable. If you do this, check that the cord cap / plug is rated minimum
250 V, 16 A, that it has a connection to ground / earth and that it has an integral cable
grip. Follow the cord cap / plug manufacturer’s assembly instructions.

If you need to install a Neutrik powerCON TRUE1 connector on a power cable, follow
the instructions given in the Support area of the Neutrik website at www.neutrik.com.

Respect the color coding used in the supplied power cable and in your local mains
power wiring system. US and EU systems use the color coding shown below:

Connecting multiple fixtures to power in a chain

You can connect fixtures to power in a daisy-chain to simplify your power circuit
layout.

EXO Wash 30 fixtures have 2.5 mm2 internal wiring from Power IN to Power THRU
connectors.

Warning! Do not connect more than four (4) EXO Wash 30 fixtures in total to
power in one chain at 100-120 V, 60 Hz. Do not connect more than eight (8)
EXO Wash 30 fixtures in total to power in one chain at 200-240 V, 50 Hz.

The power input cable supplied with the fixture is rated 16 A maximum. Add
together the maximum current draw ratings of all the devices that you
intend to connect to power in a daisy chain and do not create a chain with
a total maximum current draw of more than 16 A, or you will create a risk of
fire and electric shock.

To connect fixtures to power in a chain:

1. Obtain power relay cables that have male and female Neutrik
powerCON TRUE1 connectors. Cables must be minimum 14 AWG or 1.5mm2,
rated minimum 16 A and suitable for the environment and application.

EXO Wash 30 User Manual Rev. B 19

2. Connect the power input cable to the Mains IN socket of the first fixture
as described under ‘Connecting to power’ on page 18.

3. Connect a relay cable to the Mains OUT / THRU socket of the first fixture
and to the Mains IN socket of the second fixture.

4. If you are using 100-120 V, 60 Hz AC mains power you can continue
connecting EXO Wash 30 fixtures Mains OUT / THRU socket to Mains IN socket
until the chain contains a maximum of four (4) fixtures in total. If you are using
200-240 V, 50 Hz AC mains power you can continue connecting fixtures Mains
OUT to Mains IN until the chain contains a maximum of eight (8) fixtures total.

www.glp.de Connecting to DMX data

1

Signal Ground

2

Data –

3

Data +

4

Not used

5

Not used

6. Connecting to DMX data

Check that all cables and connectors are suitable for the installation environment and
application (see recommendations in ‘Avoiding damage to the fixture’ on page 10).

Use digital 110 Ohm DMX cable with IP65 5-pin XLR connectors to supply DMX data to
fixtures.

Keep connectors sealed with their rubber caps at all times when not in use.
The EXO Wash 30 has two 5-pin XLR sockets for IN and THRU connections to a DMX

data link. EXO Wash 30 fixtures support the USITT DMX 512A signal protocol. They also
support RDM (Remote Device Management).

The 5-pin XLR connectors use standard pin allocations:

The DMX cable should start at the console and be daisy-chained through each fixture
to be controlled using the DMX input and DMX link out connectors. If you need to split
the DMX cable, use a powered DMX splitter.

If you would like advice with planning and installing a DMX link, your GLP supplier will
be happy to provide assistance.

20 EXO Wash User Manual Rev. B

German Light Products® Starting and stopping operation

7. Starting and stopping operation

Warning! Before you apply power to the fixture or operate it after a
blackout, make sure that nobody is looking directly into the front of the
fixture.

The EXO Wash 30’s TRUE1 mains power input connector supports hot-plugging, and
connecting and disconnecting a live power cable is an option, especially if you need
to shut down power urgently, but it is still good practice to shut down power to the AC
mains power circuit before connecting and disconnecting power cables.

To start operation, check that nobody is looking into the front of the fixture, then apply
power to the AC mains power circuit.

To stop operation, shut down power to the AC mains power circuit.

EXO Wash 30 User Manual Rev. B 21

www.glp.de Features

8. Features

The EXO Wash 30 unit has the following features:

Position

Pan rotation 630°(3.9 sec) or 540°(4.3 sec),Tilt rotation 267°(2.2 sec) with 16 bit
resolution. The fixture will automatically reposition if knocked – this option can be
disabled from the menu. The Pan and Tilt movements can be inverted using the menu.

Color

The fixture has seven zones of Red/Green/Blue/White (RGBW) color mixing LEDs.
Depending on the DMX mode these have up to 16-bit dimming and can be controlled
independently, or using macro patterns.

The zones/pixels are arranged as shown in the diagram below.

Figure 5. Pixel order

22 EXO Wash User Manual Rev. B

German Light Products® Features

Figure 6. Dimming curves

Dimming

See Figure 6. You can select from two dimming curves using the control panel or the
Control / Settings DMX channel:

● Linear sets dimming so that it appears to increase and decrease evenly throughout
the dimming range.

● Soft gives finer control at low light levels and coarser control at high light levels.

The default setting is Soft.

Strobe / shutter

A variety of strobing and fading effects can be produced by the fixture.

Zoom

The beam angle of the fixture can be adjusted (zoom) from 4° to 54°. The zoom
operation can be inverted using the menu.

Behavior when the fixture is not receiving a DMX signal

You can set the fixture to react in three different ways if no DMX signal is present (if the
fixture is being controlled by DMX but the DMX signal stops, or if you apply power to
the fixture when no DMX signal is present):

● Blackout sets the fixture to black out. This is the default setting.

● Hold sets the fixture to continue obeying the last DMX values it received. If no DMX

signal was being received, the fixture will black out.

● Preset Scene sets the fixture to output a preset scene which you have previously
captured from an incoming DMX state using the Manual Control > Capture Scene
menu option. You can also manually set the control values (or edit the captured
values) using the attribute settings in the Manual Control menu.

All these settings are available via DMX on the Control / Settings channel and in the
fixture’s control panel.

EXO Wash 30 User Manual Rev. B 23

www.glp.de Control menus and onboard display

9. Control menus and onboard display

Warning! DMX control is disabled when the control menus are active. Be
prepared for the fixture to emit strong light as soon as you exit the control
menus.

The control panel and onboard LCD display provide access to user settings, readouts
and utilities.

Figure 7. Onboard display

The four control buttons have the following functions:

MODE/ESC: Activate the menus or go back one level towards the top of the
menu.

UP: Scroll up or increase a number.
DOWN: Scroll down or reduce a number.
ENTER: Activate the control panel if it is in sleep mode. Then enter a menu, select

a setting or implement a command.

When you apply power to the fixture, it boots up. After it has booted, the panel
displays the default screen.

The Battery button is used to power up the control panel for setup before mains is
connected to the unit. Battery mode can be disabled in the menu.

The W-DMX indicator shows when wireless DMX is being received, if the optional
wireless module has been fitted.

24 EXO Wash User Manual Rev. B

German Light Products® Control menus and onboard display

DMX control is disabled when the control menus are active.

Display options

The illuminated LCD display lets you change fixture settings. The display has a battery
backup so that you can change the settings before mains is connected to the fixture.
See Chapter 9 for more details.

Using the Control / Settings DMX channel or the fixture’s control panel you can:
Set display modes using the Fixture Settings > Display Mode option:

- On: The display stays on constantly. This setting can be useful when you are
configuring or servicing the fixture.

- Auto: The display will automatically switch off after a few seconds even if the fixture
is not receiving a valid control signal or if it has detected an error.

Invert the display using the Fixture Settings > Display Orientation option, so it is easier to
read if the fixture is hanging upside down.

Display Locking

On the Fixture Settings > Lock menu, you can configure the display to lock after a
period of time to prevent accidental changes to the options.

You can set a custom lock code using the Fixture Settings > Lock > Set Passcode
option. If you do not set a custom code, the default code is 0000.

Manual Control

Using the Manual Control menu you can set fixed values to the fixture’s control
channels, as if it was in DMX control mode 1. This is useful when testing.

LED PWM frequency

The LEDs in the unit are dimmed using Pulse Width Modulation (PWM) which can
sometimes cause flickering on cameras. The Fixture Settings > PWM option allows you
to select different frequencies for the PWM to fix such issues. The higher frequencies
may cause reduced dimming performance.

Fan control

The fixture has internal cooling fans. In a noise critical situation you can slow these
down using the Fixture Settings > Fan Mode option. The normal setting is Regulated
which will adjust the fan speed automatically. If you set the option to Low the fan
speed is kept slow but this may result in the fixture overheating and reducing its output.

The fixture has an additional fan near the lens to clear condensation. You can control
how this fan works using the Fixture Settings > Defog option.

Fixture information

The Information menu in the control panel gives access to items of information from
the fixture’s sensors and memory. You can check temperature sensor readouts, see
total operating hours counters, and see software version number, for example.

EXO Wash 30 User Manual Rev. B 25

www.glp.de Control menus and onboard display

Pan disable / Tilt disable

These options allow you to disable the startup reset movements or disable the drive of
the pan and/or tilt motors. The options are

- Off: Normal motor control

- Reset Disabled: The fixture will not do its power on reset sequence on this motor but

the motor is still controlled. This can be used when a fixture is mounted in a
confined space and would collide with an obstruction if it did the reset sequence.

- Current Disabled: The motor drive function is completely disabled. This is mostly
used for service or diagnostics.

Preset settings and factory defaults

You can store three different versions of option settings using the Service > Service
Advanced > Save Settings menu and load them using the Load Settings > Preset 1-2-3

options. These allow you to quickly set up the fixture in a particular configuration.
Settings are stored after a power off/on cycle and after a reset.

Two options are available in the fixture’s control panel for deleting multiple custom
settings and restoring defaults:

- Service > Default Settings reloads all the fixture’s factory default settings except
DMX address, DMX mode, captured scene, preset settings and offset values. This
option returns the fixture to baseline settings without affecting its basic
configuration in an installation.

- Service > Service Advanced > Factory Backup reloads all the fixture’s factory
default settings including DMX address, DMX mode, and erases all storage. This
option reinitializes the fixture completely and returns to its state when it left the
factory.

-

26 EXO Wash User Manual Rev. B

German Light Products® Control menu layout

Menus

Notes

DMX
ADDRESS

1 - 512

Enter DMX address

CONTROL
MODE

Compressed – 13 channels

Select DMX control mode

Standard – 22 channels

Extended – 37 channels

Pixel – 50 channels

CONTROL
PROTOCOL

DMX

Wired DMX control

WIRELESS

Wireless DMX control
(optional module)

FIXTURE
SETTINGS

Pan Invert

Off / On

Invert Pan movement

Tilt Invert

Off / On

Invert Tilt movement

Position Feedback

Off / On

If On, fixture repositions if
knocked

Pan Disabled

Off / Reset Disabled /
Current Disabled

Disable motor drive for
service

Tilt Disabled

Off / Reset Disabled /
Current Disabled

Zoom Invert

Off / On

Inverts Zoom movement

Dimmer Curve

Soft (Gamma) / Linear

Dimming curve

No Signal

Blackout / Hold / run
Captured Scene

Action when no DMX
signal

Capture Scene

Press ENTER to capture
scene

Store scene for no signal

PWM

600 Hz / 2200 Hz / 3000 Hz /
4800 Hz / 9600 Hz / 25000 Hz

Frequency of LED dimming

Display Mode

Auto / On / Off

Display blanking

Display Orientation

Normal / Upside Down

Display reversing

Max Temperature

60 – 90C / 140-194F

Sets overheat
temperature where
shutdown will occur

Fan Mode

Regulated / High / Medium
/ Low

Set fan speed control

Load Settings

Preset 1 / Preset 2 / Preset 3

Press ENTER for 3 sec to
confirm

Lock

Off / On /. Set Passcode

Lock the control panel

Defog

Off / On / Quick

Settings for lens defogging
fan

Battery

On / Off

Disable the battery
operation of the control
panel

MANUAL
CONTROL

Reboot

Press ENTER for 3 sec to
confirm

Manual function control
(DMX Mode 1)

Pan Coarse 0-255

These values can be set
manually or from a DMX
state using Capture Scene
option

Pan Fine 0-255

Tilt Coarse 0-255

Tilt Fine 0-255

Dimmer 0-255

Shutter 0-255

Virtual color wheel 0-255

10. Control menu layout

EXO Wash 30 User Manual Rev. B 27

www.glp.de Control menu layout

Red 0-255

Green 0-255

Blue 0-255

White 0-255

Zoom 0-255

Control 0-255

Capture Scene

Press ENTER for 3 sec to
capture incoming DMX
state

INFORMATIO
N

Firmware Version

ver x.x

Fixture firmware version

Fixture Details

Serial … xx / RDM … xx

Show fixture serial, RDM
unique ID

Device Life

Total / User

Shows power cycles,
Power Hours, LED Hours

DMX Link Status

Refresh Rate (Hz) / Frame
Length / Mode Length

Details of DMX signal

Temperatures

xxx…

Unit temperatures

Fan Speeds

Fan1 …

Error Log

Xxx

SERVICE

Test All

Running

Press Enter to start test,
Menu or Enter to stop

Test Pan only

Running

Test Tilt only

Running

Test LED only

Running

Test Zoom only

Running

Default Settings

See Note 1 below

Service Advanced

See below for menu

Hold Enter for 6 sec to
enter this menu

FACTORY
MENU

This menu is for use by authorized service technicians only

Note 1: Default Setting will return all options to default except DMX address, Control
Mode. It does not erase captured scene, preset settings or offset values

Default settings are written in BOLD type.

28 EXO Wash User Manual Rev. B

German Light Products® Control menu layout

Menus

Notes

Pan Disable

Off/On

Tilt Disable

Off/On

Units

°C / °F

Offsets

Tilt

xxx

Zoom

xxx

Reset
Counter

Power Hours

Power Cycles

LED Hours

Max Temperature

Temperature Unit

Save Settings

Preset 1

Preset 2

Preset 3

Factory
Backup

See Note 2 below

Service Advanced menu

Hold down Enter for 6 seconds to access this menu.

Note 2: Factory backup will reset all options to default, erase captured scene, erase
preset settings, erase offset values. User Hour counter and Temperature Unit will not be
affected.

EXO Wash 30 User Manual Rev. B 29

www.glp.de DMX control modes overview

DMX Mode 1: Compact
Compact Mode uses 13 DMX

channels.
It provides 16-bit control of pan and tilt,

dimming and a shutter with strobe and
ramp up/down effects. It has a virtual
color wheel effect (color presets with
rotation effects) and RGBW color
mixing.

Compact Mode also provides control
of zoom and a control / settings
channel that lets you configure the
feature and adjust settings remotely via
DMX.

Mode 1

Compact

1

Pan 2 Pan fine

3

Tilt

4

Tilt fine

5

Dimmer

6

Shutter

7

Virtual color wheel

8

Red 9 Green

10

Blue

11

White

12

Zoom

13

Control / Settings

DMX Mode 2: Standard
Standard Mode uses 22 DMX channels.

It provides 16-bit control of pan and tilt,
16-bit control of dimming and a shutter
with strobe and ramp up/down effects.
It has a virtual color wheel effect (color
presets with rotation effects), color
temperature control and 16-bit RGBW
color mixing.

Standard Mode also gives access to a
range of Pattern FX with variable
speed and crossfading parameters,
control of zoom and a control / settings
channel that lets you configure the
feature and adjust settings remotely via
DMX.

Mode 2

Standard

1

Pan

2

Pan fine

3

Tilt

4

Tilt fine

5

Dimmer

6

Dimmer fine

7

Shutter

8

Virtual color wheel

9

CTC

10

Red

11

Red fine

12

Green

13

Green fine

14

Blue

15

Blue fine

16

White

17

White fine

18

Pattern

19

Pattern Speed

20

Pattern Fading

21

Zoom

22

Control / Settings

11. DMX control modes overview

The following DMX control modes are available in the EXO Wash 30.

30 EXO Wash User Manual Rev. B

German Light Products® DMX control modes overview

DMX Mode 3: Extended
Extended Mode uses 37 DMX channels.
It provides 16-bit control of pan and tilt,

16-bit control of dimming and a shutter
with strobe and ramp up/down effects.
It has a virtual color wheel effect (color
presets with rotation effects), color
temperature control and 16-bit RGBW
color mixing.

Extended Mode also has two layers:

● Layer 1, the background layer, has
16-bit color dimming and a shutter
effect that includes a random pixel
strobe.

● Layer 2, the top layer, has a range
of Pattern FX with 16-bit dimming,
shutter effects and color control via
a virtual color wheel (color presets)
and 16-bit RGBW color mixing. Layer
2 also has variable speed and
crossfading parameters

Extended Mode also provides control
of zoom and a control / settings
channel that lets you configure the
feature and adjust settings remotely via
DMX.

Mode 3

Extended

1

Pan

2

Pan fine

3

Tilt

4

Tilt fine

5

Dimmer

6

Dimmer fine

7

Shutter

8

Virtual color wheel

9

CTC

10

Red

11

Red fine

12

Green

13

Green fine

14

Blue

15

Blue fine

16

White

17

White fine

18

Layer 1 Color dimmer

19

Layer 1 Color dimmer fine

20

Layer 1 Shutter

21

Layer 2 Pattern dimmer

22

Layer 2 Pattern dimmer fine

23

Layer 2 Pattern shutter

24

Layer 2 Pattern color wheel

25

Layer 2 Pattern red

26

Layer 2 Pattern red fine

27

Layer 2 Pattern green

28

Layer 2 Pattern green fine

29

Layer 2 Pattern blue

30

Layer 2 Pattern blue fine

31

Layer 2 Pattern white

32

Layer 2 Pattern white fine

33

Layer 2 Pattern

34

Layer 2 Pattern speed

35

Layer 2 Pattern fading

36

Zoom

37

Control / Settings

EXO Wash 30 User Manual Rev. B 31

www.glp.de DMX control modes overview

DMX Mode 4: Pix
Pix Mode uses 50 DMX channels.

It provides 16-bit control of pan and tilt,
16-bit control of dimming and a shutter
with strobe and ramp up/down effects.
It has a virtual color wheel effect (color
presets with rotation effects), color
temperature control and 16-bit RGBW
color mixing.

Pix Mode also gives access to a range
of Pattern FX with variable speed and
crossfading parameters, control of
zoom and a control / settings channel
that lets you configure the feature and
adjust settings remotely via DMX.

Finally, Pix Mode provides independent
RGBW color mixing on each of the
fixture’s seven pixels.

Mode 4

Pix

1

Pan

2

Pan fine

3

Tilt

4

Tilt fine

5

Dimmer

6

Dimmer fine

7

Shutter

8

Virtual color wheel

9

CTC

10

Red

11

Red fine

12

Green

13

Green fine

14

Blue

15

Blue fine

16

White

17

White fine

18

Pattern

19

Pattern Speed

20

Pattern Fading

21

Zoom

22

Control / Settings

23

Pixel 1 Red

24

Pixel 1 Green

25

Pixel 1 Blue

26

Pixel 1 White

27

Pixel 2 Red

28

Pixel 2 Green

29

Pixel 2 Blue

30

Pixel 2 White

31

Pixel 3 Red

32

Pixel 3 Green

33

Pixel 3 Blue

34

Pixel 3 White

35

Pixel 4 Red

36

Pixel 4 Green

37

Pixel 4 Blue

38

Pixel 4 White

39

Pixel 5 Red

40

Pixel 5 Green

41

Pixel 5 Blue

42

Pixel 5 White

43

Pixel 6 Red

44

Pixel 6 Green

45

Pixel 6 Blue

46

Pixel 6 White

47

Pixel 7 Red

48

Pixel 7 Green

49

Pixel 7 Blue

50

Pixel 7 White

32 EXO Wash User Manual Rev. B

German Light Products® DMX MODE 1

Channel

Command

DMX

range

Percent

Default

DMX

Fade

1

Pan

Pan left–right

0

65535

0

100

32767

Fade

2

Pan fine

3

Tilt

Tilt up–down

0

65535

0

100

32767

Fade

4

Tilt fine

5

Dimmer

Intensity 0–100%

0

255 0 100

0

Fade

6

Shutter

Shutter closed

0 4 0

1.6

0

Snap

Single flash when change on dimmer
channel

5 9 2.0

3.5

Sync ramp up slow–fast

10

39

3.9

15.3

Sync ramp down slow–fast

40

69

15.7

27.1

Sync ramp up-down slow–fast

70

99

27.5

38.8

Sync double flash (slow–fast)

100

129

39.2

50.6

Random strobe pixel (slow–fast)

130

159

51.0

62.4

Random strobe all (slow–fast)

160

199

62.7

78.0

Sync strobe (1 Hz–10 Hz)

200

250

78.4

98.0

Shutter open

251

255

98.4

100

7

Color wheel
effect

Off (RGBW)

0 7 0

2.7

0

Snap

Color 01 - Red

8

15

3.1

5.9

Snap

Color 02 - Amber

16

23

6.3

9.0

Snap

Color 03 - Warm Yellow

24

31

9.4

12.2

Snap

Color 04 - Yellow

32

39

12.5

15.3

Snap

Color 05 - Green

40

47

15.7

18.4

Snap

Color 06 - Turquoise

48

55

18.8

21.6

Snap

Color 07 - Cyan

56

63

22.0

24.7

Snap

Color 08 - Blue

64

71

25.1

27.8

Snap

Color 09 - Lavender

72

79

28.2

31.0

Snap

Color 10 - Mauve

80

87

31.4

34.1

Snap

Color 11 - Magenta

88

95

34.5

37.3

Snap

Color 12 - Pink

96

103

37.6

40.4

Snap

Color 13 - White 3200K

104

111

40.8

43.5

Snap

Color 14 - White 5600K

112

119

43.9

46.7

Snap

Color 15 - White 7200K

120

127

47.1

49.8

Snap

Stop

128

128

50.2

50.2

Snap

Rainbow colors crossfade slow > fast

129

223

50.6

87.5

Fade

Random colors crossfade slow > fast

224

255

87.8

100

Fade

8

Red

Red intensity 0-100%

0

255 0 100

0

Fade

9

Green

Green intensity 0-100%

0

255 0 100

0

Fade

10

Blue

Blue intensity 0-100%

0

255 0 100

0

Fade

11

White

White intensity 0-100%

0

255 0 100

0

Fade

12

Zoom

Wide–narrow

0

255 0 100

0

Fade

12. DMX control channel layout tables

DMX Mode 1: Compact

11 DMX Channels

EXO Wash 30 User Manual Rev. B 33

www.glp.de DMX MODE 1

13

Control /
Settings

No function

0 9 0.0

3.5

0

Snap

Dimmer curve: Extra-soft (3s hold)

10

15

3.9

5.9

Dimmer curve: Linear (3s hold)

16

21

6.3

8.2

Display mode: Auto (3s hold)

22

27

8.6

10.6

Display mode: On (3s hold)

28

33

11.0

12.9

Display mode: Off (3s hold)

34

39

13.3

15.3

Display orientation: Normal (3s hold)

40

45

15.7

17.6

Display orientation: Inverted (3s hold)

46

51

18.0

20.0

No DMX: Blackout (3s hold)

52

57

20.4

22.4

No DMX: Hold (3s hold)

58

63

22.7

24.7

No DMX: Stand-alone (3s hold)

64

69

25.1

27.1

Fan mode: Regulated (3s hold)

70

75

27.5

29.4

Fan mode: High (3s hold)

76

81

29.8

31.8

Fan mode: Medium (3s hold)

82

87

32.2

34.1

Fan mode: Low (3s hold)

88

93

34.5

36.5

Position feedback: Off (3s hold)

94

99

36.9

38.8

Position feedback: On (3s hold)

100

105

39.2

41.2

No function

106

117

41.6

45.9

Tilt inversion: Off (3s hold)

118

123

46.3

48.2

Tilt inversion: On (3s hold)

124

129

48.6

50.6

Pan inversion: Off (3s hold)

130

135

51.0

52.9

Pan inversion: On (3s hold)

136

141

53.3

55.3

Zoom inversion: Off (3s hold)

142

147

55.7

57.6

Zoom inversion: On (3s hold)

148

153

58.0

60.0

Defog: Off

154

159

60.4

62.4

Defog: On

160

165

62.7

64.7

Defog: Quick

166

171

65.1

67.1

Load Settings Preset1

172

177

67.5

69.4

Load Settings Preset2

178

183

69.8

71.8

Load Settings Preset3

184

189

72.2

74.1

PWM 600 Hz (5s hold)

190

195

74.5

76.5

PWM: 2200 Hz (5s hold)

196

201

76.9

78.8

PWM: 3000 Hz (5s hold)

202

207

79.2

81.2

PWM: 4800 Hz (5s hold)

208

213

81.6

83.5

PWM: 9600 Hz (5s hold)

214

219

83.9

85.9

PWM: 25 kHz (5s hold)

220

225

86.3

88.2

No function

226

231

88.6

90.6

Return to default settings

232

237

91.0

92.9

Reset Pan/Tilt (3s hold)

238

243

93.3

95.3

Reset Head (3s hold)

244

249

95.7

97.6

Reset All (3s hold)

250

255

98.0

100

34 EXO Wash User Manual Rev. B

German Light Products® DMX MODE 2

Channel

Command

DMX

range

Percent

Defaul

t DMX

Fade

1

Pan

Pan left–right

0

65535

0

100

32767

Fade

2

Pan fine

3

Tilt

Tilt up–down

0

65535

0

100

32767

Fade

4

Tilt fine

5

Dimmer

Intensity 0–100%

0

65535

0

100

32767

Fade

6

Dimmer fine

7

Shutter

Shutter closed

0 4 0

1.6

0

Snap

Single flash when change on dimmer
channel

5 9 2.0

3.5

Sync ramp up slow–fast

10

39

3.9

15.3

Sync ramp down slow–fast

40

69

15.7

27.1

Sync ramp up-down slow–fast

70

99

27.5

38.8

Sync double flash (slow–fast)

100

129

39.2

50.6

Random strobe pixel (slow–fast)

130

159

51.0

62.4

Random strobe all (slow–fast)

160

199

62.7

78.0

Sync strobe (1 Hz–10 Hz)

200

250

78.4

98.0

Shutter open

251

255

98.4

100

8

Color wheel
effect

Off (RGBW)

0 7 0

2.7

0

Snap

Color 01 - Red

8

15

3.1

5.9

Snap

Color 02 - Amber

16

23

6.3

9.0

Snap

Color 03 - Warm Yellow

24

31

9.4

12.2

Snap

Color 04 - Yellow

32

39

12.5

15.3

Snap

Color 05 - Green

40

47

15.7

18.4

Snap

Color 06 - Turquoise

48

55

18.8

21.6

Snap

Color 07 - Cyan

56

63

22.0

24.7

Snap

Color 08 - Blue

64

71

25.1

27.8

Snap

Color 09 - Lavender

72

79

28.2

31.0

Snap

Color 10 - Mauve

80

87

31.4

34.1

Snap

Color 11 - Magenta

88

95

34.5

37.3

Snap

Color 12 - Pink

96

103

37.6

40.4

Snap

Color 13 - White 3200K

104

111

40.8

43.5

Snap

Color 14 - White 5600K

112

119

43.9

46.7

Snap

Color 15 - White 7200K

120

127

47.1

49.8

Snap

Stop

128

128

50.2

50.2

Snap

Rainbow colors crossfade slow > fast

129

223

50.6

87.5

Fade

Random colors crossfade slow > fast

224

255

87.8

100

Fade

9

Color
Temperature
(Kelvin)

RAW 0 15 0 5.9

Snap

10000

16

18

6.3

7.1

9900

19

21

7.5

8.2

9800

22

24

8.6

9.4

9700

25

27

9.8

10.6

9600

28

30

11.0

11.8

9500

31

33

12.2

12.9

9400

34

36

13.3

14.1

9300

37

39

14.5

15.3

9200

40

42

15.7

16.5

9100

43

45

16.9

17.6

9000

46

48

18.0

18.8

8900

49

51

19.2

20.0

8800

52

54

20.4

21.2

8700

55

57

21.6

22.4

DMX Mode 2: Standard

22 DMX Channels

EXO Wash 30 User Manual Rev. B 35

www.glp.de DMX MODE 2

8600

58

60

22.7

23.5

8500

61

63

23.9

24.7

8400

64

66

25.1

25.9

8300

67

69

26.3

27.1

8200

70

72

27.5

28.2

8100

73

75

28.6

29.4

8000

76

78

29.8

30.6

7900

79

81

31.0

31.8

7800

82

84

32.2

32.9

7700

85

87

33.3

34.1

7600

88

90

34.5

35.3

7500

91

93

35.7

36.5

7400

94

96

36.9

37.6

7300

97

99

38.0

38.8

7200

100

102

39.2

40.0

7100

103

105

40.4

41.2

7000

106

108

41.6

42.4

6900

109

111

42.7

43.5

6800

112

114

43.9

44.7

6700

115

117

45.1

45.9

6600

118

120

46.3

47.1

6500

121

123

47.5

48.2

6400

124

126

48.6

49.4

6300

127

129

49.8

50.6

6200

130

132

51.0

51.8

6100

133

135

52.2

52.9

6000

136

138

53.3

54.1

5900

139

141

54.5

55.3

5800

142

144

55.7

56.5

5700

145

147

56.9

57.6

5600

148

150

58.0

58.8

5500

151

153

59.2

60.0

5400

154

156

60.4

61.2

5300

157

159

61.6

62.4

5200

160

162

62.7

63.5

5100

163

165

63.9

64.7

5000

166

168

65.1

65.9

4900

169

171

66.3

67.1

4800

172

174

67.5

68.2

4700

175

177

68.6

69.4

4600

178

180

69.8

70.6

4500

181

183

71.0

71.8

4400

184

186

72.2

72.9

4300

187

189

73.3

74.1

4200

190

192

74.5

75.3

4100

193

195

75.7

76.5

4000

196

198

76.9

77.6

3900

199

201

78.0

78.8

3800

202

204

79.2

80.0

3700

205

207

80.4

81.2

3600

208

210

81.6

82.4

3500

211

213

82.7

83.5

3400

214

216

83.9

84.7

3300

217

219

85.1

85.9

3200

220

222

86.3

87.1

3100

223

225

87.5

88.2

3000

226

228

88.6

89.4

2900

229

231

89.8

90.6

36 EXO Wash User Manual Rev. B

German Light Products® DMX MODE 2

2800

232

234

91.0

91.8

2700

235

237

92.2

92.9

2600

238

240

93.3

94.1

2500

241

255

94.5

100

10

Red

Red intensity 0–100%

0

65535

0

100

32767

Fade

11

Red fine

12

Green

Green intensity 0–100%

0

65535

0

100

32767

Fade

13

Green fine

14

Blue

Blue intensity 0–100%

0

65535

0

100

32767

Fade

15

Blue fine

16

White

White intensity 0–100%

0

65535

0

100

32767

Fade

17

White fine

18

Pattern

Static pattern

0

51 0 20.0

0

Snap

Chase animation

52

131

20.4

51.4

Fade animation

132

211

51.8

82.7

Random

212

255

83.1

100

19

Pattern speed

Slow–fast

0

255 0 100

0

Fade

20

Pattern fade

Slow crossfade–snap

0

255 0 100

0

Fade

21

Zoom

Wide–narrow

0

255 0 100

0

Fade

22

Control /
Settings

No function

0 9 0.0

3.5

0

Snap

Dimmer curve: Extra-soft (3s hold)

10

15

3.9

5.9

Dimmer curve: Linear (3s hold)

16

21

6.3

8.2

Display mode: Auto (3s hold)

22

27

8.6

10.6

Display mode: On (3s hold)

28

33

11.0

12.9

Display mode: Off (3s hold)

34

39

13.3

15.3

Display orientation: Normal (3s hold)

40

45

15.7

17.6

Display orientation: Inverted (3s hold)

46

51

18.0

20.0

No DMX: Blackout (3s hold)

52

57

20.4

22.4

No DMX: Hold (3s hold)

58

63

22.7

24.7

No DMX: Stand-alone (3s hold)

64

69

25.1

27.1

Fan mode: Regulated (3s hold)

70

75

27.5

29.4

Fan mode: High (3s hold)

76

81

29.8

31.8

Fan mode: Medium (3s hold)

82

87

32.2

34.1

Fan mode: Low (3s hold)

88

93

34.5

36.5

Position feedback: Off (3s hold)

94

99

36.9

38.8

Position feedback: On (3s hold)

100

105

39.2

41.2

No function

106

117

41.6

45.9

Tilt inversion: Off (3s hold)

118

123

46.3

48.2

Tilt inversion: On (3s hold)

124

129

48.6

50.6

Pan inversion: Off (3s hold)

130

135

51.0

52.9

Pan inversion: On (3s hold)

136

141

53.3

55.3

Zoom inversion: Off (3s hold)

142

147

55.7

57.6

Zoom inversion: On (3s hold)

148

153

58.0

60.0

Defog: Off

154

159

60.4

62.4

Defog: On

160

165

62.7

64.7

Defog: Quick

166

171

65.1

67.1

Load Settings Preset1

172

177

67.5

69.4

Load Settings Preset2

178

183

69.8

71.8

Load Settings Preset3

184

189

72.2

74.1

PWM: 600 Hz (5s hold)

190

195

74.5

76.5

PWM: 2200 Hz (5s hold)

196

201

76.9

78.8

PWM: 3000 Hz (5s hold)

202

207

79.2

81.2

PWM: 4800 Hz (5s hold)

208

213

81.6

83.5

PWM: 9600 Hz (5s hold)

214

219

83.9

85.9

PWM: 25 kHz (5s hold)

220

225

86.3

88.2

EXO Wash 30 User Manual Rev. B 37

www.glp.de DMX MODE 2

No function

226

231

88.6

90.6

Return to default settings

232

237

91.0

92.9

Reset Pan/Tilt (3s hold)

238

243

93.3

95.3

Reset Head (3s hold)

244

249

95.7

97.6

Reset All (3s hold)

250

255

98.0

100

38 EXO Wash User Manual Rev. B

German Light Products® DMX control channel layout tables

Channel

Command

DMX

range

Percent

Default

DMX

Fade

1

Pan

Pan left–right

0

65535

0

100

32767

Fade

2

Pan fine

3

Tilt

Tilt up–down

0

65535

0

100

32767

Fade

4

Tilt fine

5

Dimmer

Intensity 0–100%

0

65535

0

100

32767

Fade

6

Dimmer fine

7

Shutter

Shutter closed

0 4 0

1.6

0

Snap

Single flash when change on dimmer
channel

5 9 2.0

3.5

Sync ramp up slow–fast

10

39

3.9

15.3

Sync ramp down slow–fast

40

69

15.7

27.1

Sync ramp up-down slow–fast

70

99

27.5

38.8

Sync double flash (slow–fast)

100

129

39.2

50.6

Random strobe pixel (slow–fast)

130

159

51.0

62.4

Random strobe all (slow–fast)

160

199

62.7

78.0

Sync strobe (1 Hz–10 Hz)

200

250

78.4

98.0

Shutter open

251

255

98.4

100

8

Color wheel
effect

Off (RGBW)

0 7 0

2.7

0

Snap

Color 01 - Red

8

15

3.1

5.9

Snap

Color 02 - Amber

16

23

6.3

9.0

Snap

Color 03 - Warm Yellow

24

31

9.4

12.2

Snap

Color 04 - Yellow

32

39

12.5

15.3

Snap

Color 05 - Green

40

47

15.7

18.4

Snap

Color 06 - Turquoise

48

55

18.8

21.6

Snap

Color 07 - Cyan

56

63

22.0

24.7

Snap

Color 08 - Blue

64

71

25.1

27.8

Snap

Color 09 - Lavender

72

79

28.2

31.0

Snap

Color 10 - Mauve

80

87

31.4

34.1

Snap

Color 11 - Magenta

88

95

34.5

37.3

Snap

Color 12 - Pink

96

103

37.6

40.4

Snap

Color 13 - White 3200K

104

111

40.8

43.5

Snap

Color 14 - White 5600K

112

119

43.9

46.7

Snap

Color 15 - White 7200K

120

127

47.1

49.8

Snap

Stop

128

128

50.2

50.2

Snap

Rainbow colors crossfade slow > fast

129

223

50.6

87.5

Fade

Random colors crossfade slow > fast

224

255

87.8

100

Fade

9

Color
Temperature
(Kelvin)

RAW 0 15 0 5.9

Snap

10000

16

18

6.3

7.1

9900

19

21

7.5

8.2

9800

22

24

8.6

9.4

9700

25

27

9.8

10.6

9600

28

30

11.0

11.8

9500

31

33

12.2

12.9

9400

34

36

13.3

14.1

9300

37

39

14.5

15.3

9200

40

42

15.7

16.5

9100

43

45

16.9

17.6

9000

46

48

18.0

18.8

8900

49

51

19.2

20.0

8800

52

54

20.4

21.2

8700

55

57

21.6

22.4

8600

58

60

22.7

23.5

8500

61

63

23.9

24.7

8400

64

66

25.1

25.9

DMX Mode 3: Extended

37 DMX Channels

EXO Wash 30 User Manual Rev. B 39

www.glp.de DMX control channel layout tables

8300

67

69

26.3

27.1

8200

70

72

27.5

28.2

8100

73

75

28.6

29.4

8000

76

78

29.8

30.6

7900

79

81

31.0

31.8

7800

82

84

32.2

32.9

7700

85

87

33.3

34.1

7600

88

90

34.5

35.3

7500

91

93

35.7

36.5

7400

94

96

36.9

37.6

7300

97

99

38.0

38.8

7200

100

102

39.2

40.0

7100

103

105

40.4

41.2

7000

106

108

41.6

42.4

6900

109

111

42.7

43.5

6800

112

114

43.9

44.7

6700

115

117

45.1

45.9

6600

118

120

46.3

47.1

6500

121

123

47.5

48.2

6400

124

126

48.6

49.4

6300

127

129

49.8

50.6

6200

130

132

51.0

51.8

6100

133

135

52.2

52.9

6000

136

138

53.3

54.1

5900

139

141

54.5

55.3

5800

142

144

55.7

56.5

5700

145

147

56.9

57.6

5600

148

150

58.0

58.8

5500

151

153

59.2

60.0

5400

154

156

60.4

61.2

5300

157

159

61.6

62.4

5200

160

162

62.7

63.5

5100

163

165

63.9

64.7

5000

166

168

65.1

65.9

4900

169

171

66.3

67.1

4800

172

174

67.5

68.2

4700

175

177

68.6

69.4

4600

178

180

69.8

70.6

4500

181

183

71.0

71.8

4400

184

186

72.2

72.9

4300

187

189

73.3

74.1

4200

190

192

74.5

75.3

4100

193

195

75.7

76.5

4000

196

198

76.9

77.6

3900

199

201

78.0

78.8

3800

202

204

79.2

80.0

3700

205

207

80.4

81.2

3600

208

210

81.6

82.4

3500

211

213

82.7

83.5

3400

214

216

83.9

84.7

3300

217

219

85.1

85.9

3200

220

222

86.3

87.1

3100

223

225

87.5

88.2

3000

226

228

88.6

89.4

2900

229

231

89.8

90.6

2800

232

234

91.0

91.8

2700

235

237

92.2

92.9

2600

238

240

93.3

94.1

2500

241

255

94.5

100

10

Red

Red intensity 0–100%

0

65535

0

100

32767

Fade

11

Red fine

40 EXO Wash User Manual Rev. B

German Light Products® DMX control channel layout tables

12

Green

Green intensity 0–100%

0

65535

0

100

32767

Fade

13

Green fine

14

Blue

Blue intensity 0–100%

0

65535

0

100

32767

Fade

15

Blue fine

16

White

White intensity 0–100%

0

65535

0

100

32767

Fade

17

White fine

18

Layer 1 DImmer

Layer 1 (background)
intensity 0–100%

0

65535

0

100

32767

Fade

19

Layer 1 Dimmer
fine

20

Layer 1 Shutter

Layer 1 (background) shutter closed

0 4 0

1.6

0

Snap

Single flash when change on dimmer
channel

5 9 2.0

3.5

Sync ramp up slow–fast

10

39

3.9

15.3

Sync ramp down slow–fast

40

69

15.7

27.1

Sync ramp up-down slow–fast

70

99

27.5

38.8

Sync double flash (slow–fast)

100

129

39.2

50.6

Random strobe pixel (slow–fast)

130

159

51.0

62.4

Random strobe all (slow–fast)

160

199

62.7

78.0

Sync strobe (1 Hz–10 Hz)

200

250

78.4

98.0

Shutter open

251

255

98.4

100

21

Layer 2 DImmer

Layer 2 (top layer)
intensity 0–100%

0

65535

0

100

32767

Fade

22

Layer 2
Dimmer fine

23

Layer 2 Pattern
Shutter

Shutter closed

0 4 0

1.6

0

Snap

Single flash when change on dimmer
channel

5 9 2.0

3.5

Sync ramp up slow–fast

10

39

3.9

15.3

Sync ramp down slow–fast

40

69

15.7

27.1

Sync ramp up-down slow–fast

70

99

27.5

38.8

Sync double flash (slow–fast)

100

129

39.2

50.6

Random strobe pixel (slow–fast)

130

159

51.0

62.4

Random strobe all (slow–fast)

160

199

62.7

78.0

Sync strobe (1 Hz–10 Hz)

200

250

78.4

98.0

Shutter open

251

255

98.4

100

24

Layer 2 Pattern
color wheel
effect

Layer 2 (top layer) pattern off (RGBW)

0 7 0

2.7

0

Snap

Color 01 - Red

8

15

3.1

5.9

Snap

Color 02 - Amber

16

23

6.3

9.0

Snap

Color 03 - Warm Yellow

24

31

9.4

12.2

Snap

Color 04 - Yellow

32

39

12.5

15.3

Snap

Color 05 - Green

40

47

15.7

18.4

Snap

Color 06 - Turquoise

48

55

18.8

21.6

Snap

Color 07 - Cyan

56

63

22.0

24.7

Snap

Color 08 - Blue

64

71

25.1

27.8

Snap

Color 09 - Lavender

72

79

28.2

31.0

Snap

Color 10 - Mauve

80

87

31.4

34.1

Snap

Color 11 - Magenta

88

95

34.5

37.3

Snap

Color 12 - Pink

96

103

37.6

40.4

Snap

Color 13 - White 3200K

104

111

40.8

43.5

Snap

Color 14 - White 5600K

112

119

43.9

46.7

Snap

Color 15 - White 7200K

120

127

47.1

49.8

Snap

Stop

128

128

50.2

50.2

Snap

Rainbow colors crossfade slow > fast

129

223

50.6

87.5

Fade

Random colors crossfade slow > fast

224

255

87.8

100

Fade

25

Layer 2 Pattern
Red

Layer 2 (top layer) pattern
red intensity 0–100%

0

65535

0

100

32767

Fade

26

Layer 2 Pattern
Red fine

27

Layer 2 Pattern
Green

Layer 2 (top layer) pattern
green intensity 0–100%

0

65535

0

100

32767

Fade

EXO Wash 30 User Manual Rev. B 41

www.glp.de DMX control channel layout tables

28

Layer 2 Pattern
Green fine

29

Layer 2 Pattern
Blue

Layer 2 (top layer) pattern
blue intensity 0–100%

0

65535

0

100

32767

Fade

30

Layer 2 Pattern
Blue fine

31

Layer 2 Pattern
White

Layer 2 (top layer) pattern
white intensity 0–100%

0

65535

0

100

32767

Fade

32

Layer 2 Pattern
White fine

33

Layer 2 Pattern

Layer 2 (top layer) static pattern

0

51 0 20.0

0

Snap

Chase animation

52

131

20.4

51.4

Fade animation

132

211

51.8

82.7

Random

212

255

83.1

100

34

Layer 2 Pattern
speed

Slow–fast

0

255 0 100

0

Fade

35

Layer 2 Pattern
fade

Slow crossfade–snap

0

255 0 100

0

Fade

36

Zoom

Wide–narrow

0

255 0 100

0

Fade

37

Control /
Settings

No function

0 9 0.0

3.5

0

Snap

Dimmer curve: Extra-soft (3s hold)

10

15

3.9

5.9

Dimmer curve: Linear (3s hold)

16

21

6.3

8.2

Display mode: Auto (3s hold)

22

27

8.6

10.6

Display mode: On (3s hold)

28

33

11.0

12.9

Display mode: Off (3s hold)

34

39

13.3

15.3

Display orientation: Normal (3s hold)

40

45

15.7

17.6

Display orientation: Inverted (3s hold)

46

51

18.0

20.0

No DMX: Blackout (3s hold)

52

57

20.4

22.4

No DMX: Hold (3s hold)

58

63

22.7

24.7

No DMX: Stand-alone (3s hold)

64

69

25.1

27.1

Fan mode: Regulated (3s hold)

70

75

27.5

29.4

Fan mode: High (3s hold)

76

81

29.8

31.8

Fan mode: Medium (3s hold)

82

87

32.2

34.1

Fan mode: Low (3s hold)

88

93

34.5

36.5

Position feedback: Off (3s hold)

94

99

36.9

38.8

Position feedback: On (3s hold)

100

105

39.2

41.2

No function

106

117

41.6

45.9

Tilt inversion: Off (3s hold)

118

123

46.3

48.2

Tilt inversion: On (3s hold)

124

129

48.6

50.6

Pan inversion: Off (3s hold)

130

135

51.0

52.9

Pan inversion: On (3s hold)

136

141

53.3

55.3

Zoom inversion: Off (3s hold)

142

147

55.7

57.6

Zoom inversion: On (3s hold)

148

153

58.0

60.0

Defog: Off

154

159

60.4

62.4

Defog: On

160

165

62.7

64.7

Defog: Quick

166

171

65.1

67.1

Load Settings Preset1

172

177

67.5

69.4

Load Settings Preset2

178

183

69.8

71.8

Load Settings Preset3

184

189

72.2

74.1

PWM: 600 Hz (5s hold)

190

195

74.5

76.5

PWM: 2200 Hz (5s hold)

196

201

76.9

78.8

PWM: 3000 Hz (5s hold)

202

207

79.2

81.2

PWM: 4800 Hz (5s hold)

208

213

81.6

83.5

PWM: 9600 Hz (5s hold)

214

219

83.9

85.9

PWM: 25 kHz (5s hold)

220

225

86.3

88.2

No function

226

231

88.6

90.6

Return to default settings

232

237

91.0

92.9

Reset Pan/Tilt (3s hold)

238

243

93.3

95.3

42 EXO Wash User Manual Rev. B

German Light Products® DMX control channel layout tables

Reset Head (3s hold)

244

249

95.7

97.6

Reset All (3s hold)

250

255

98.0

100

EXO Wash 30 User Manual Rev. B 43

www.glp.de DMX control channel layout tables

Channel

Command

DMX

range

Percent

Default

DMX

Fade

1

Pan

Pan left–right

0

65535

0

100

32767

Fade

2

Pan fine

3

Tilt

Tilt up–down

0

65535

0

100

32767

Fade

4

Tilt fine

5

Dimmer

Intensity 0–100%

0

65535

0

100

32767

Fade

6

Dimmer fine

7

Shutter

Shutter closed

0 4 0

1.6

0

Snap

Single flash when change on dimmer
channel

5 9 2.0

3.5

Sync ramp up slow–fast

10

39

3.9

15.3

Sync ramp down slow–fast

40

69

15.7

27.1

Sync ramp up-down slow–fast

70

99

27.5

38.8

Sync double flash (slow–fast)

100

129

39.2

50.6

Random strobe pixel (slow–fast)

130

159

51.0

62.4

Random strobe all (slow–fast)

160

199

62.7

78.0

Sync strobe (1 Hz–10 Hz)

200

250

78.4

98.0

Shutter open

251

255

98.4

100

8

Color wheel
effect

Off (RGBW)

0 7 0

2.7

0

Snap

Color 01 - Red

8

15

3.1

5.9

Snap

Color 02 - Amber

16

23

6.3

9.0

Snap

Color 03 - Warm Yellow

24

31

9.4

12.2

Snap

Color 04 - Yellow

32

39

12.5

15.3

Snap

Color 05 - Green

40

47

15.7

18.4

Snap

Color 06 - Turquoise

48

55

18.8

21.6

Snap

Color 07 - Cyan

56

63

22.0

24.7

Snap

Color 08 - Blue

64

71

25.1

27.8

Snap

Color 09 - Lavender

72

79

28.2

31.0

Snap

Color 10 - Mauve

80

87

31.4

34.1

Snap

Color 11 - Magenta

88

95

34.5

37.3

Snap

Color 12 - Pink

96

103

37.6

40.4

Snap

Color 13 - White 3200K

104

111

40.8

43.5

Snap

Color 14 - White 5600K

112

119

43.9

46.7

Snap

Color 15 - White 7200K

120

127

47.1

49.8

Snap

Stop

128

128

50.2

50.2

Snap

Rainbow colors crossfade slow > fast

129

223

50.6

87.5

Fade

Random colors crossfade slow > fast

224

255

87.8

100

Fade

9

Color
Temperature
(Kelvin)

RAW 0 15 0 5.9

Snap

10000

16

18

6.3

7.1

9900

19

21

7.5

8.2

9800

22

24

8.6

9.4

9700

25

27

9.8

10.6

9600

28

30

11.0

11.8

9500

31

33

12.2

12.9

9400

34

36

13.3

14.1

9300

37

39

14.5

15.3

9200

40

42

15.7

16.5

9100

43

45

16.9

17.6

9000

46

48

18.0

18.8

8900

49

51

19.2

20.0

8800

52

54

20.4

21.2

8700

55

57

21.6

22.4

8600

58

60

22.7

23.5

8500

61

63

23.9

24.7

8400

64

66

25.1

25.9

DMX Mode 4: Pix

50 DMX Channels

44 EXO Wash User Manual Rev. B

German Light Products® DMX control channel layout tables

8300

67

69

26.3

27.1

8200

70

72

27.5

28.2

8100

73

75

28.6

29.4

8000

76

78

29.8

30.6

7900

79

81

31.0

31.8

7800

82

84

32.2

32.9

7700

85

87

33.3

34.1

7600

88

90

34.5

35.3

7500

91

93

35.7

36.5

7400

94

96

36.9

37.6

7300

97

99

38.0

38.8

7200

100

102

39.2

40.0

7100

103

105

40.4

41.2

7000

106

108

41.6

42.4

6900

109

111

42.7

43.5

6800

112

114

43.9

44.7

6700

115

117

45.1

45.9

6600

118

120

46.3

47.1

6500

121

123

47.5

48.2

6400

124

126

48.6

49.4

6300

127

129

49.8

50.6

6200

130

132

51.0

51.8

6100

133

135

52.2

52.9

6000

136

138

53.3

54.1

5900

139

141

54.5

55.3

5800

142

144

55.7

56.5

5700

145

147

56.9

57.6

5600

148

150

58.0

58.8

5500

151

153

59.2

60.0

5400

154

156

60.4

61.2

5300

157

159

61.6

62.4

5200

160

162

62.7

63.5

5100

163

165

63.9

64.7

5000

166

168

65.1

65.9

4900

169

171

66.3

67.1

4800

172

174

67.5

68.2

4700

175

177

68.6

69.4

4600

178

180

69.8

70.6

4500

181

183

71.0

71.8

4400

184

186

72.2

72.9

4300

187

189

73.3

74.1

4200

190

192

74.5

75.3

4100

193

195

75.7

76.5

4000

196

198

76.9

77.6

3900

199

201

78.0

78.8

3800

202

204

79.2

80.0

3700

205

207

80.4

81.2

3600

208

210

81.6

82.4

3500

211

213

82.7

83.5

3400

214

216

83.9

84.7

3300

217

219

85.1

85.9

3200

220

222

86.3

87.1

3100

223

225

87.5

88.2

3000

226

228

88.6

89.4

2900

229

231

89.8

90.6

2800

232

234

91.0

91.8

2700

235

237

92.2

92.9

2600

238

240

93.3

94.1

2500

241

255

94.5

100

10

Red

Red intensity 0–100%

0

65535

0

100

32767

Fade

11

Red fine

EXO Wash 30 User Manual Rev. B 45

www.glp.de DMX control channel layout tables

12

Green

Green intensity 0–100%

0

65535

0

100

32767

Fade

13

Green fine

14

Blue

Blue intensity 0–100%

0

65535

0

100

32767

Fade

15

Blue fine

16

White

White intensity 0–100%

0

65535

0

100

32767

Fade

17

White fine

18

Pattern

Static pattern

0

51 0 20.0

0

Snap

Chase animation

52

131

20.4

51.4

Fade animation

132

211

51.8

82.7

Random

212

255

83.1

100

19

Pattern speed

Slow–fast

0

255 0 100

0

Fade

20

Pattern fade

Slow crossfade–snap

0

255 0 100

0

Fade

21

Zoom

Wide–narrow

0

255 0 100

0

Fade

22

Control /
Settings

No function

0 9 0.0

3.5

0

Snap

Dimmer curve: Extra-soft (3s hold)

10

15

3.9

5.9

Dimmer curve: Linear (3s hold)

16

21

6.3

8.2

Display mode: Auto (3s hold)

22

27

8.6

10.6

Display mode: On (3s hold)

28

33

11.0

12.9

Display mode: Off (3s hold)

34

39

13.3

15.3

Display orientation: Normal (3s hold)

40

45

15.7

17.6

Display orientation: Inverted (3s hold)

46

51

18.0

20.0

No DMX: Blackout (3s hold)

52

57

20.4

22.4

No DMX: Hold (3s hold)

58

63

22.7

24.7

No DMX: Stand-alone (3s hold)

64

69

25.1

27.1

Fan mode: Regulated (3s hold)

70

75

27.5

29.4

Fan mode: High (3s hold)

76

81

29.8

31.8

Fan mode: Medium (3s hold)

82

87

32.2

34.1

Fan mode: Low (3s hold)

88

93

34.5

36.5

Position feedback: Off (3s hold)

94

99

36.9

38.8

Position feedback: On (3s hold)

100

105

39.2

41.2

No function

106

117

41.6

45.9

Tilt inversion: Off (3s hold)

118

123

46.3

48.2

Tilt inversion: On (3s hold)

124

129

48.6

50.6

Pan inversion: Off (3s hold)

130

135

51.0

52.9

Pan inversion: On (3s hold)

136

141

53.3

55.3

Zoom inversion: Off (3s hold)

142

147

55.7

57.6

Zoom inversion: On (3s hold)

148

153

58.0

60.0

Defog: Off

154

159

60.4

62.4

Defog: On

160

165

62.7

64.7

Defog: Quick

166

171

65.1

67.1

Load Settings Preset1

172

177

67.5

69.4

Load Settings Preset2

178

183

69.8

71.8

Load Settings Preset3

184

189

72.2

74.1

PWM: 600 Hz (5s hold)

190

195

74.5

76.5

PWM: 2200 Hz (5s hold)

196

201

76.9

78.8

PWM: 3000 Hz (5s hold)

202

207

79.2

81.2

PWM: 4800 Hz (5s hold)

208

213

81.6

83.5

PWM: 9600 Hz (5s hold)

214

219

83.9

85.9

PWM: 25 kHz (5s hold)

220

225

86.3

88.2

No function

226

231

88.6

90.6

Return to default settings

232

237

91.0

92.9

Reset Pan/Tilt (3s hold)

238

243

93.3

95.3

Reset Head (3s hold)

244

249

95.7

97.6

Reset All (3s hold)

250

255

98.0

100

23

Pixel 1 Red

Intensity 0-100%

0

255 0 100

0

Fade

24

Pixel 1 Green

Intensity 0-100%

0

255 0 100

0

Fade

25

Pixel 1 Blue

Intensity 0-100%

0

255 0 100

0

Fade

46 EXO Wash User Manual Rev. B

German Light Products® DMX control channel layout tables

26

Pixel 1 White

Intensity 0-100%

0

255 0 100

0

Fade

27

Pixel 2 Red

Intensity 0-100%

0

255 0 100

0

Fade

28

Pixel 2 Green

Intensity 0-100%

0

255 0 100

0

Fade

29

Pixel 2 Blue

Intensity 0-100%

0

255 0 100

0

Fade

30

Pixel 2 White

Intensity 0-100%

0

255 0 100

0

Fade

31

Pixel 3 Red

Intensity 0-100%

0

255 0 100

0

Fade

32

Pixel 3 Green

Intensity 0-100%

0

255 0 100

0

Fade

33

Pixel 3 Blue

Intensity 0-100%

0

255 0 100

0

Fade

34

Pixel 3 White

Intensity 0-100%

0

255 0 100

0

Fade

35

Pixel 4 Red

Intensity 0-100%

0

255 0 100

0

Fade

36

Pixel 4 Green

Intensity 0-100%

0

255 0 100

0

Fade

37

Pixel 4 Blue

Intensity 0-100%

0

255 0 100

0

Fade

38

Pixel 4 White

Intensity 0-100%

0

255 0 100

0

Fade

39

Pixel 5 Red

Intensity 0-100%

0

255 0 100

0

Fade

40

Pixel 5 Green

Intensity 0-100%

0

255 0 100

0

Fade

41

Pixel 5 Blue

Intensity 0-100%

0

255 0 100

0

Fade

42

Pixel 5 White

Intensity 0-100%

0

255 0 100

0

Fade

43

Pixel 6 Red

Intensity 0-100%

0

255 0 100

0

Fade

44

Pixel 6 Green

Intensity 0-100%

0

255 0 100

0

Fade

45

Pixel 6 Blue

Intensity 0-100%

0

255 0 100

0

Fade

46

Pixel 6 White

Intensity 0-100%

0

255 0 100

0

Fade

47

Pixel 7 Red

Intensity 0-100%

0

255 0 100

0

Fade

48

Pixel 7 Green

Intensity 0-100%

0

255 0 100

0

Fade

49

Pixel 7 Blue

Intensity 0-100%

0

255 0 100

0

Fade

50

Pixel 7 White

Intensity 0-100%

0

255 0 100

0

Fade

EXO Wash 30 User Manual Rev. B 47

www.glp.de Service

Warning! There are no user-serviceable parts inside the fixture. Opening the
fixture can compromise its IP65 rating and cause damage that is not covered
by the product warranty. Any service operation that requires removal of a
cover must be performed by a professional service technician with the tools,
skills, and personal protective equipment to maintain high-powered lighting
equipment safely and efficiently.

13. Service

Cleaning

EXO Wash 30 fixtures require occasional cleaning to prevent the buildup of dust, dirt, and
residue from atmospheric effects. Failure to keep the fixture clean will significantly reduce
light output and may cause heat buildup and damage that is not covered by the product
warranty. Regular cleaning will ensure maximum performance and reliable operation.

The cleaning schedule depends on the operating environment. Check fixtures regularly for
signs of dirt buildup.

You can clean the fixture using a soft cloth slightly dampened with a household or
automotive glass cleaning product. Do not apply pressure to the clear front or display on
the back of the fixture, as you may scratch these surfaces.

Use the tilt lock mechanism to hold the head in a vertical position for easier cleaning.

GLP Service and Support

Contact information for the nearest GLP Service and Support is available online at
www.glp.de/en/service, by email at [e-mail], or by telephone at the following
numbers:

● GLP Germany: [phone]

● GLP N. America: [phone]

● GLP UK: [phone]

● GLP Asia: [phone]

● GLP Nordic: [phone]

48 EXO Wash User Manual Rev. B

German Light Products® Technical specifications

14. Technical specifications

Optics

Light source: 7x 40W Osram RGBW LEDs
Lifetime: 20 000 hrs. approx. to > 70% luminous output
Luminous flux: 40995 lux @ 3 m, 14758 lux @ 5 m
Beam angle (half peak): 4° to 54°

Control

Control systems: DMX, RDM, Manual setting
DMX channel footprint: 13 / 22 / 37 / 50 depending on mode
Setting and addressing: Onboard control panel with LCD display, RDM
DMX compliance: USITT DMX512
RDM compliance: ANSI/ESTA E1.20
Pan range: 630°, 16 bit resolution
Tilt range: 267°, 16 bit resolution

Installation

Options: Stand on horizontal surface, suspended using truss mount brackets
Operating position: Any
Minimum distance to combustible materials: 0.5 m (20 in.)
Minimum distance to illuminated surfaces: 0.5 m (20 in.)
Installation environment: Temporary or permanent indoor installation, temporary outdoor

installation
Secondary attachment: Slot for safety cable attachment

Electrical

AC mains power: 100-240 V nominal, 50/60 Hz
Power supply unit: Auto-ranging electronic switch mode
Maximum power consumption, all LEDs at 100% output: 300 W

Maximum permitted number of fixtures daisy-chained to power

4 x EXO Wash 30 total @ 100-120 V, 60 Hz
8 x EXO Wash 30 total @ 200-240 V, 50 Hz

Connections

AC mains power in and thru (out): Neutrik powerCON TRUE1 with sealing cap
Control data in and thru (out): Neutrik 5-pin XLR with sealing cap

Construction

Ingress protection rating: IP65
Fixture housing: Aluminum, plastic
Color: Black

Thermal

Cooling: Fan, Convection
Minimum ambient temperature: -10° C (14° F)
Maximum ambient temperature: 40° C (104° F)

EXO Wash 30 User Manual Rev. B 49

www.glp.de Technical specifications

Included items

Power cable with Neutrik powerCON TRUE1 mains input plug

Dimensions and weight

Length: 279mm / 11.0 ins.
Width: 380 mm / 15.0 ins.
Height: 521 mm / 20.5 ins.
Weight: 19.7 kg (43.4 lbs.)

50 EXO Wash User Manual Rev. B

German Light Products® Dimensions

15. Dimensions

All dimensions are in millimeters

EXO Wash 30 User Manual Rev. B 51