Furuno 1742c, 1752c, 1762, 1762c, 1742 User Manual
...
MARINE RADAR
MODEL1722/1732/1742/1752/1762
MODEL1722C/1732C/1742C/1752C/1762C
C
All rights reserved.
PUB. No. OME- 34940
( HIMAD
FIRST EDITION : APR. 2001
9-52, Ashihara- cho,
Nishinomiya, Japan
Telephone: 0798-65-2111
Telefax: 0798-65-4200
Printed in Japan
Your Local Agent/Dealer
E1 : MAY 17, 2002
MODEL 1722/C SERIES
SAFETY INSTRUCTIONS
WARNING
ELECTRICAL SHOCK HAZARD
Do not open the equipment.
Only qualified personnel
should work inside the
equipment.
Do not disassemble or modify the
equipment.
Fire, electrical shock or serious injury can
result.
Immediately turn off the power at the
switchboard if the equipment is emitting
smoke or fire.
Continued use of the equipment can cause
fire or electrical shock. Contact a FURUNO
agent for service.
Keep heater away from equipment.
WARNING
Radio Frequency
Radiation Hazard
The radar antenna emits electromagnetic
radio frequency (RF) energy which can be
harmful, particularly to your eyes. Never
look directly into the antenna aperture from
a close distance while the radar is in
operation or expose yourself to the transmitting antenna at a close distance.
Distances at which RF radiation levels of
100 and 10 W/m
table below.
Note: If the antenna unit is installed at a
close distance in front of the wheel house,
your administration may require halt of
transmission within a certain sector of
antenna revolution. This is possible - Ask
your FURUNO representative or dealer to
provide this feature.
2
exist are given in the
A heater can melt the equipment's power
cord, which can cause fire or electrical
shock.
Use the proper fuse.
Fuse rating is shown on the equipment.
Use of a wrong fuse can result in damage
to the equipment.
CAUTION
A warning label is attached to the equipment. Do not remove the label. If the
label is missing or damaged, contact
a FURUNO agent or dealer about
replacement.
WARNING
To avoid electrical shock, do not
remove cover. No user-serviceable
parts inside.
Name: Warning Label (1)
Type: 86-003-1011-0
Code No.: 100-236-230
MODEL
1722
1732
1742
1752
1762
Distance to
100 W/m
point
Nil
Nil
Nil
0.15 m
0.20 m
Distance to
2
Worst case
0.50 m
Worst case
0.50 m
Worst case
1.00 m
Worst case
3.00 m
10 W/m
Worst case
2.00 m
2
point
CAUTION
No one navigation device should ever be
solely replied upon for the navigation of
a vessel.
Always confirm position against all available
aids to navigation, for safety of vessel and
crew.
i
TABLE OF CONTENTS
FOREWORD ...................................................................................................... viii
SYSTEM CONFIGURATIONS .............................................................................. x
1. OPERATIONAL OVERVIEW .........................................................................1-1
1.1 Operating Controls ...................................................................................................... 1-2
1.1.1 Display unit controls ......................................................................................... 1-2
1.1.2 Remote controller............................................................................................. 1-5
1.2 Inserting a Chart Card ................................................................................................. 1-6
1.3 Turn ing the Unit On/ Off................................................................................................ 1-7
1.4 Cursor Pad, Cursor...................................................................................................... 1-8
1.5 Display Brilliance, Panel Brilliance, Contrast, Hue....................................................... 1-9
1.5.1 Display brilliance, panel brilliance..................................................................... 1-9
1.5.2 Contrast...........................................................................................................1-10
1.5.3 Hue (MODEL1722C series).............................................................................1-10
1.6 Selecting a Display.....................................................................................................1-11
1.6.1 Display modes.................................................................................................1-11
1.6.2 Selecting a display ..........................................................................................1-12
1.6.3 Switching control in combination and overlay screens.....................................1-13
1.6.4 Selecting radar source.....................................................................................1-14
1.7 Data Boxes.................................................................................................................1-15
1.7.1 Showing, hiding data boxes with soft key........................................................1-15
1.7.2 Rearranging data boxes..................................................................................1-15
1.7.3 Temporarily erasing a data box........................................................................1-15
1.8 Function Keys.............................................................................................................1-16
1.8.1 Executing a function........................................................................................1-16
1.9 Simulation Display......................................................................................................1-17
2. RADAR OPERATION.....................................................................................2-1
2.1 Radar Display.............................................................................................................. 2-1
2.2 Transmi tti ng, Stand-by................................................................................................. 2-2
2.3 Tun ing ......................................................................................................................... 2-2
2.4 Adjusting the Gain....................................................................................................... 2-2
2.5 Reducing Sea Clutter .................................................................................................. 2-4
2.5.1 How the A/C SEA works................................................................................... 2-4
2.5.2 Adjusting A/C SEA ........................................................................................... 2-4
2.6 Reducing Precipitation Clutter..................................................................................... 2-5
2.6.1 Adjusting the A/C RAIN.................................................................................... 2-5
2.6.2 Adjusting the FTC............................................................................................. 2-6
2.7 Range Scale................................................................................................................ 2-7
2.8 Pulselength.................................................................................................................. 2-8
ii
2.9 Presentation Mode.......................................................................................................2-9
2.9.1 Selecting a presentation mode..........................................................................2-9
2.9.2 Description of presentation modes..................................................................2-10
2.10 Measuring the Range...............................................................................................2-12
2.10.1 Measuring range by range rings....................................................................2-12
2.10.2 Meas u ring range by cursor...........................................................................2-13
2.10.3 Mea su ring range by VRM.............................................................................2-14
2.10.4 Erasing a VRM, VRM indication....................................................................2-15
2.10.5 Erasing EBL/VRM data boxes.......................................................................2-15
2.10.6 Hiding EBL/VRM data boxes.........................................................................2-15
2.10.7 Moving EBL/VRM data boxes.......................................................................2-15
2.11 Measuring the Bearing.............................................................................................2-15
2.11.1 Measuring bearing by cursor ......................................................................... 2-15
2.11.2 Measuring bearing by EBL............................................................................2-15
2.11.3 Erasing an EBL, EBL indication.....................................................................2-16
2.11.4 Erasing EBL/VRM data boxes.......................................................................2-16
2.11.5 Hiding EBL/VRM data boxes......................................................................... 2-16
2.11.6 Moving EBL/VRM data boxes........................................................................2-16
2.12 Erasing the Heading Line, North Marker ..................................................................2-17
2.13 Reducing Noise........................................................................................................2-17
2.14 Reducing Radar Interference...................................................................................2-18
2.15 Zoom.......................................................................................................................2-19
2.15.1 Zooming in on radar targets..........................................................................2-19
2.15.2 Zooming ARP, TTM targets...........................................................................2-19
2.16 Shifting the Picture...................................................................................................2-20
2.16.1 Manual shift..................................................................................................2-20
2.16.2 Automatic shift..............................................................................................2-21
2.17 Using the O ffset EBL................................................................................................2-22
2.17.1 Predicting a collision course..........................................................................2-22
2.17.2 Measuring range & bearing between two targets..........................................2-23
2.18 Echo Trails...............................................................................................................2-24
2.18.1 Trail time.......................................................................................................2-24
2.18.2 Starting echo trails........................................................................................2-25
2.18.3 Trail brilliance (MODEL1722 series)..............................................................2-25
2.18.4 Trail gradation (MODEL1722C series)..........................................................2-25
2.18.5 Trai l color (MODEL1722C series).................................................................2-26
2.19 Echo Stretch............................................................................................................2-27
2.20 Echo Averaging........................................................................................................2-28
2.21 Outputting TLL Data.................................................................................................2-29
2.22 Guard Ala rm.............................................................................................................2-30
2.22.1 Setting a guard alarm zone...........................................................................2-30
2.22.2 When the alarm is violated…........................................................................2-31
2.22.3 Canceling the guard alarm............................................................................2-31
2.23 Watchma n................................................................................................................2-32
2.23.1 How watchman works...................................................................................2-32
2.23.2 Turning on/off watchman............................................................................... 2-32
2.23.3 Setting watchman stand-by interval ..............................................................2-32
2.24 Waypoi nt Marker......................................................................................................2-33
iii
2.25 ARP (optio n ), TTM operation....................................................................................2-34
2.25.1 Activating/deactivating ARP, TTM..................................................................2-35
2.25.2 Acquiring and tracking targets (ARP only).....................................................2-36
2.25.3 Displaying target number (internal, external ARP).........................................2-37
2.25.4 Terminating tracking of ARP targets..............................................................2-38
2.25.5 Setting vector attributes (ARP) ......................................................................2-39
2.25.6 Displaying past position display (ARP)..........................................................2-40
2.25.7 ARP, TTM target data....................................................................................2-41
2.25.8 CPA/TCPA alarm (ARP) ................................................................................2-42
2.25.9 Lost target alarm (ARP).................................................................................2-43
2.26 Interpreting the Radar Display..................................................................................2-44
2.26.1 General .........................................................................................................2-44
2.26.2 False echoes.................................................................................................2-46
2.26.3 SART (Search and Rescue Transponder) .....................................................2-48
2.26.4 Racon (Radar Beacon)..................................................................................2-50
3. PLOTTER OPERATION.................................................................................3-1
3.1 Plotter Displays............................................................................................................3-1
3.1.1 Full-screen plotter display................................................................................. 3-1
3.1.2 Compass display.............................................................................................. 3-3
3.1.3 Highway display............................................................................................... 3-5
3.1.4 Nav data display............................................................................................... 3-6
3.2 Presentation Mode...................................................................................................... 3-7
3.2.1 North-up........................................................................................................... 3-7
3.2.2 Course-up ........................................................................................................ 3-8
3.2.3 Auto course-up................................................................................................. 3-8
3.3 Shifting the Display...................................................................................................... 3-9
3.4 Chart Scale.................................................................................................................. 3-9
3.5 Chart Cards................................................................................................................3-10
3.5.1 Chart card overview.........................................................................................3-10
3.5.2 Indices and chart enlargement ........................................................................3-11
3.5.3 FURUNO and NavCharts™.............................................................................3-12
3.5.4 C-MAP cards...................................................................................................3-14
3.6 Workin g with T ra c k.....................................................................................................3-18
3.6.1 Displaying track...............................................................................................3-18
3.6.2 Stopping, restating plotting of own ship track...................................................3-19
3.6.3 Changing track color (MODEL1722C series)...................................................3-20
3.6.4 Track plotting method and interval for own ship track......................................3-21
3.6.5 Changing own ship track/mark distribution setting...........................................3-22
3.6.6 Erasing track...................................................................................................3-23
3.7 Marks, Lines...............................................................................................................3-25
3.7.1 Entering a mark...............................................................................................3-25
3.7.2 Changing mark attributes ................................................................................3-25
3.7.3 Selecting line type ...........................................................................................3-26
3.7.4 Erasing marks, lines........................................................................................3-27
3.8 Waypoin ts...................................................................................................................3-29
3.8.1 Entering waypoints..........................................................................................3-29
3.8.2 Editing waypoint data ......................................................................................3-32
iv
3.8.3 Erasing waypoints........................................................................................... 3-34
3.8.4 Changing waypoint mark size (FURUNO, NavCharts™).................................3-35
3.8.5 Searching waypoints.......................................................................................3-36
3.9 Routes.......................................................................................................................3-37
3.9.1 Creating routes...............................................................................................3-37
3.9.2 Connecting routes...........................................................................................3-41
3.9.3 Inserting waypoints.........................................................................................3-42
3.9.4 Removing waypoints from a route...................................................................3-44
3.9.5 Erasing routes.................................................................................................3-44
3.10 Navigation ................................................................................................................ 3-45
3.10.1 Navigating to a "quick point" .........................................................................3-45
3.10.2 Navigating to waypoints................................................................................3-46
3.10.3 Navigating to ports, port services (NavCharts™ only)...................................3-47
3.10.4 Following a route...........................................................................................3-49
3.11 Alarms ....................................................................................................................3-53
3.11.1 Audio alarm on/off.........................................................................................3-53
3.11.2 Arrival alarm..................................................................................................3-54
3.11.3 Anchor watch alarm ......................................................................................3-55
3.11.4 XTE (Cross Track Error) alarm......................................................................3-56
3.11.5 Speed alarm..................................................................................................3-56
3.11.6 Proximity alarm.............................................................................................3-57
3.11.7 Trip alarm...................................................................................................... 3-58
3.11.8 Alarm information.......................................................................................... 3-59
3.12 Resetting Trip Distance............................................................................................3-60
3.13 Entering the MOB Mark, Setting MOB as Destination ..............................................3-61
4. VIDEO SOUNDER OPERATION...................................................................4-1
4.1 Principle of Operation...................................................................................................4-1
4.2 Sounder Displays.........................................................................................................4-2
4.2.1 Selecting a sounder display..............................................................................4-2
4.2.2 Description of sounder displays........................................................................4-3
4.2.3 Selecting screen split method in combination displays......................................4-7
4.3 Automatic Sounder Operation......................................................................................4-8
4.3.1 How the automatic sounder works....................................................................4-8
4.3.2 Types of automatic sounder modes..................................................................4-8
4.3.3 How to enable automatic sounder operation.....................................................4-8
4.4 Manual Sounder Operation..........................................................................................4-9
4.4.1 Selecting the manual mode...............................................................................4-9
4.4.2 Selecting display range.....................................................................................4-9
4.4.3 Adjusting the gain.............................................................................................4-9
4.4.4 Range shifting.................................................................................................4-10
4.5 Measuring Depth, Time.............................................................................................. 4-11
4.6 Reducing Interference................................................................................................ 4-12
4.7 Reducing Low Level Noise.........................................................................................4-13
4.8 Erasing Weak Echoes ..............................................................................................4-14
4.9 White Marker (MODEL1722C series).........................................................................4-15
v
4.10 Picture Advance Speed............................................................................................4-16
4.10.1 Advancement independent of ship’s speed....................................................4-16
4.10.2 Advancement synchronized with ship’s speed...............................................4-17
4.11 Display Colors (MODEL1722C series)......................................................................4-18
4.12 Alarms......................................................................................................................4-19
4.12.1 Audio alarm on/off .........................................................................................4-19
4.12.2 Bottom alarm.................................................................................................4-20
4.12.3 Fish alarm .....................................................................................................4-20
4.12.4 Fish alarm (B/L).............................................................................................4-21
4.12.5 Wate r temperatu re alarm...............................................................................4-22
4.12.6 When an alarm setting is violated..................................................................4-23
4.13 Water Temperature Graph........................................................................................4-24
4.14 Interpreting the Sounder Display...............................................................................4-25
4.14.1 Zero line........................................................................................................4-25
4.14.2 Bottom echo..................................................................................................4-25
4.14.3 Fish school echoes........................................................................................4-26
4.14.4 Surface noise/Aeration..................................................................................4-26
5. CUSTOMIZING YOUR UNIT..........................................................................5-1
5.1 Generic Setup ............................................................................................................. 5-1
5.2 Radar Setup................................................................................................................ 5-3
5.2.1 Radar display setup.......................................................................................... 5-3
5.2.2 Radar range setup............................................................................................ 5-6
5.2.3 Function key setup........................................................................................... 5-7
5.3 Plotter Setup................................................................................................................ 5-9
5.3.1 Navigation options............................................................................................ 5-9
5.3.2 Function key setup..........................................................................................5-10
5.4 Chart Setup................................................................................................................5-12
5.4.1 Chart offset......................................................................................................5-12
5.4.2 FURUNO, Nav-Charts™ chart attributes.........................................................5-13
5.4.3 C-MAP chart attributes....................................................................................5-16
5.5 Data Boxes Setup.......................................................................................................5-20
5.6 Hot Page Setup..........................................................................................................5-21
5.7 Navigator Setup..........................................................................................................5-23
5.7.1 Navigation data source....................................................................................5-23
5.7.2 GPS receiver setup (Set equipped with GP-310B/320B).................................5-24
5.7.3 TD display setup..............................................................................................5-27
5.8 Nav Data Display Setup..............................................................................................5-29
5.9 Sounder Setup............................................................................................................5-30
5.9.1 System setup...................................................................................................5-30
5.9.2 Sensor setup...................................................................................................5-32
5.9.3 Sounding range, zoom range, bottom lock range ............................................5-33
5.9.4 Function key setup..........................................................................................5-34
vi
6. DATA TRANSFER..........................................................................................6-1
6.1 Memory Card Operations.............................................................................................6-1
6.1.1 Formatting memory cards.................................................................................6-1
6.1.2 Saving data to a memory card..........................................................................6-2
6.1.3 Playing back data from a memory card.............................................................6-4
6.2 Uploading, Downloading Data......................................................................................6-5
6.2.1 Setting communication software on the PC.......................................................6-5
6.2.2 Uploading or downloading data.........................................................................6-5
6.3 Loading Waypoint Data from Yeoman..........................................................................6-8
6.4 Receiving Data Via Network Equipment.......................................................................6-9
6.5 Outputting Data Through the Network........................................................................6-10
7. MAINTENANCE, TROUBLESHOOTING ......................................................7-1
7.1 Preventive Maintenance...............................................................................................7-1
7.2 Replacement of Fuse...................................................................................................7-2
7.3 Replacement of Battery................................................................................................7-2
7.4 Simple Troubleshooting................................................................................................7-3
7.4.1 General.............................................................................................................7-3
7.4.2 Radar................................................................................................................7-4
7.4.3 Plotter...............................................................................................................7-5
7.4.4 Sounder............................................................................................................7-6
7.5 Diagnostics..................................................................................................................7-7
7.5.1 Memory I/O test................................................................................................7-7
7.5.2 Test pattern..................................................................................................... 7-10
7.5.3 Keyboard, remote controller test..................................................................... 7-11
7.6 GPS Status Display...................................................................................................7-12
7.7 Clearing Memories.....................................................................................................7-13
7.8 Error Messages..........................................................................................................7-14
APPENDIX ........................................................................................................ A-1
Menu Overview..................................................................................................................A-1
Geodetic Chart List..........................................................................................................A-12
World Time Chart.............................................................................................................A-13
Icons................................................................................................................................A-14
SPECIFICATION .............................................................................................SP-1
INDEX..........................................................................................................Index-1
Declaration of Comformity
vii
FOREWORD
A Word to the Owner of the MODEL1722/1722C Series
Marine Radar
FURUNO Electric Company thanks you for purchasing t he MODEL1722/1722C
Series Marine Radar. We are confident you will discover why the FURUNO
name has become synonym ous with quality and reliability.
For over 50 years FURUNO Electric Company has enjoyed an enviable
reputation for quality and reliability throughout the world. This dedication to
excellence is furthered by our extensive global network of agents and dealers.
Your radar is designed and constructed t o meet the rigorous demands of the
marine environment. However, no machine can perform its intended function
unless properly installed and maintained. Please carefully read and f ollow the
operation and maintenance procedures set f orth in this manual.
We would appreciate feedback from you, the end-user, about whether we are
achieving our purposes.
Thank you for considering and purchasing FURUNO.
viii
Features
The MODEL1722/1722C series work within our new product-network system
called the “NavNet.” Each product has an IP address to communicate with
NavNet compatible products within the network, using TCP/IP protocol through
an Ethernet 10 Base-T network.
The main features are
! Bright 7” screen visible even under direct sunlight.
! User friendly operation with combination of discrete keys, soft keys and
! Accepts FURUNO and Nav-charts™ (NAVIONICS) or C-MAP charts.
! Fast chart redraw.
! Built-in NavNet interface circuit board.
! 12-channel GPS Receiver GP-310B with highly accurate position fixing
! User programmable function keys.
! Video sounder picture available with connection to optional network
! ARP function (when connecting with MODEL1833/1833C series)
Note: WAAS, available in North America, is a system of satellites and ground
stations that provide GPS signal corrections, giving you better position accuracy,
typically within three meters. Other systems are currently under developm ent :
Multi-Functional Satellite Augmentation System (MSAS) in Japan, and Euro
Geostationary Navigation Overlay Service (EGNOS) for Europe.
The systems will be compatible with each other, so that by selecting WAAS
below will enable reception of the signal from any system. Unless ot herwise
specified this manual uses "WAAS" when referring to these position-fixing
systems.
FOREWORD
cursor pad.
optionally available or GP-320B with WAAS (see the note in below.)
sounder.
ix
SYSTEM CONFIGURATIONS
All NavNet products incorporate a “network circuit board” to integrate each
NavNet product on board through an optional LAN cable (Ethernet 10BASE-T).
Each NavNet product is assigned an IP address to enable transfer of images
between other NavNet products. For example, video plotter pictures can be
transferred to a radar and vice versa. Pictures received via the NavNet may be
adjusted at the receiving end.
A NavNet system may consist of up to four display units and one ETR. For a
system incorporating three or more product s , a “hub” is required to process data.
NavNet system
NavNet system
x
Two-unit NavNet system
Two-unit NavNet system
SYSTEM CONFIGURATIONS
Three-or more unit NavNet system (Max. 4 NavNet capable display units)
Three-or more unit NavNet system
xi
This page is intentionally left blank .
1. OPERATIONAL OVERVIEW
This chapter provides basic information needed to get you started using your
radar. The follow topics are presented:
• Control overview
• Chart card insertion
• Power on/off
• Contrast, brilliance and hue (Color series only) adjustment s
• Display selection
• Data boxes
• Function keys
• Simulation display
NOTICE
The brilliance of the LCD is adjustable
to match a wide variety of lighting
conditions. However, its maximum
setting may not be sufficiently bright
to permit viewing of the display with
polarized sunglasses.
Note: The example screens shown in this manual may not match the screens
you see on your display. The screen you see depends on your system
configuration and equipment set tings.
1-1
1. OPERATIONAL OVERVIEW
1.1 Operating Controls
1.1.1 Display unit controls
Overview of display unit cont rols
The radar systems are mainly operated with controls of the display unit (and
remote controller). Ten keys are labeled and they provide the function shown on
their labels. The five soft keys provide various functions according to current
operating mode. The [ENT ER] knob mainly functions to register selections on
the menu and enter alphanumeric data. The cursor pad’s main function is to
move the cursor across the screen. Whenever you operate a key, a single beep
confirms operation. Invalid operation causes the unit to emit three beeps.
Selects display mode.
Momentary press:
Registers own ship’s
position as a waypoint.
Press three seconds:
Marks man overboard
position.
Soft keys
Shows or hides the soft
keys, function keys,
nav data alternately.
Cursor pad
Selects menu items and options;
shifts cursor. Press, release and
press again to change setting
consecutively.
Opens/closes the alarm menu.
Clears data; erases selected mark.
Opens/closes the main menu.
Selects a range.
ENTER knob
Push: Registers options on menus.
Rotate: Selects character; adjusts sensitivity
(sounder, radar); chooses menu items and options.
Displays the soft keys for EBL/VRM.
Radar: Displays the soft keys for adjustment of
gain, A/C SEA, A/C RAIN and FTC.
Sounder: Adjusts gain.
Long press: Turns power on/off.
Momentary press: Opens the
display for adjustment of brilliance,
etc. For radar, switches STBY and TX.
Chart slot
Control panel
1-2
1. OPERATIONAL OVERVIEW
Soft keys
The five soft keys’ functions change according t o the operation. Their labels for
their current functions are shown on the screen to the left of the keys. To hide or
show the soft keys, press the [HIDE/SHOW] key. Each press of the key shows
preset soft keys, user function keys or turns off navigation information (at the top
of the screen).
SOFT
KEYS
Display unit
Some soft keys show the current state of the soft key function in reverse video
as shown below.
.125nm
SP
.250/ 319.9
°
H-UP
*: Only when MODEL 1833/C series are
used as radar source.
M
359.9°R
+
0.24nm
SIGNAL
PROCESS
I. REJ
LOW
E. AVG*
OFF
PULSE
SHORT
E. STR
LOW
RETURN
Plotter display
Current option
shown in reverse
video
1-3
1. OPERATIONAL OVERVIEW
[ENTER] knob
The [ENTER] knob functions to
• Register data
• Enter alphanumeric data such as waypoint name
• Select menu item s and options
• Adjust setting
Clockwise rotation of the knob selects an alphabet, symbol or numeric, in one of
the sequences shown below. After you have selected desired alphanumeric
character push the [ENTER] knob to register your selection.
[ENTER] knob
ENTER knob
Alphabet, symbol, numeric
A ! B ! C ! D ! E ! F ! G ! H ! I ! J ! K ! L ! M ! N ! O ! P ! Q !
R ! S ! T ! U ! V ! W ! X ! Y ! Z ! & ! _ ! ’ ! # ! 0 ! 1 ! 2 ! 3 !
4 ! 5 ! 6 ! 7 ! 8 ! 9
Numerics
0 ! 1 ! 2 ! 3 ! 4 ! 5 ! 6 ! 7 ! 8 ! 9
1-4
1.1.2 Remote controller
RANGE
ABC1DEF2GHI
4
JKL
STU
EBL / VRM
WPT
MNO
7
VWX
’#
DISP
0
Operating distance
90°: Up to 5 m
±45°: Up to 3 m
SAVE
Replace the batteries (AA) when the
MOB
distance from which the display
unit can be operated shortens.
3
Note: The remote controller may
65
PQR
become damaged if dropped.
Mishandling of the remote
98
YZ&
controller is not covered by
the warranty.
GAIN
CENTER
1. OPERATIONAL OVERVIEW
MARK
ENT
BRILL
ENT
CLEAR
TONE
SK3SK1 SK2
MENU
TX /STBY
ALARM
SK4 SK5
CNTL
ACQ
HIDE /SHOW
Remote controller
Key Function Key Function
RANGE Same as RANGE key on
display unit.
DISP Same as DISP key on
display unit.
SAVE MOB Same as SAVE MOB key on
CLEAR Same as CLEAR key on
display unit.
MENU Same as MENU key on
display unit.
BRILL Adjusts display brilliance.
display unit.
Ten keys Enter alphanumerics. TONE Adjusts display contrast.
EBL/VRM Same as EBL/VRM key on
display unit.
TX/STBY Toggles radar between
standby and transmit.
GAIN Same as GAIN key on
display unit.
ACQ Acquires radar target.
(Requires radar source
equipped with ARP.)
WPT Displays “alphabet” WPT list
on plotter display.
MARK ENT Same as MARK ENTRY soft
key.
CENTER Ret ur ns own ship to screen
center on plotter display.
CNTL Switches control between
displays on combination
ALARM Same as ALARM key on the
display unit.
HIDE/SHOW Same as HIDE/SHOW key
on display unit.
SK1 – SK5
(soft keys)
ENT
Same as soft keys on
display unit.
Same as ENTER knob on
display unit.
displays.
1-5
1. OPERATIONAL OVERVIEW
1.2 Inserting a Chart Card
Your unit reads FURUNO and Nav-Chart s™ (NAVIONICS), or C-MAP chart
cards, depending on its specifications. Insert the appropriat e chart card for your
area as follows:
1. Open the chart card slot lid.
Chart slot
Display unit
2. Insert desired chart card groove side up.
3. Close the lid to protect the chart drive.
Note 1: Do not insert or remove the chart card while turning power on. This may
cause the equipment to freeze.
Note 2: Do not remove a card while the chart is being drawn. This may cause
the equipment to freeze.
Note 3: A card remover is supplied to ease removal of chart cards. Attach the
card remover to the right-hand side hole on the card and pull to remove
card. You can leave the card remover attached to the card while the
card is in the card slot - push the card remover leftward until it contacts
the recessed area in the card.
Note 4: For multiple display units, do not use the same chart card type in more
than one display unit.
1-6
Chart card and card remover
1.3 Turning the Unit On/Off
Press the [POWER/BRILL] key to turn the unit on. A beep sounds and the
equipment proceeds in the sequence shown below, displaying the product
information screen, startup test results and the chart usage disclaimer, in that
order. The startup test checks the ROM, RAM, internal battery and backup data
for proper operation, displaying the results for each as OK or NG (No Good). If
NG appears, an appropriate message appears on the screen. F or any NG, try to
press any key to go to the chart disclaimer screen, then perform the diagnostic
test referring to the paragraph “7.6 Diagnostics.”
Chart List
Host Name
RADAR PLOTTER
STATION NAME:
RADAR
FURUNO ELECTRIC CO., LTD.
CHARTS AVAILABLE
FLYBRDG = ANB01004
RADAR = ANB01003
è
STARTUP TEST
ROM OK
RAM OK
BACKUP DATA OK
INTERNAL BATTERY OK
1. OPERATIONAL OVERVIEW
** = Program version no.
(Two program version numbers.
One for NAVIO and one for C-MAP.)
NO NATIONAL HYDROGRAPHIC
OFFICE HAS VERIFIED THE
INFORMATION IN THIS
COASTLINE DATA CARD AND NONE
ACCEPT LIABILITY FOR THE
ACCURACY OF REPRODUCTION OR
ANY MODIFICATIONS MADE
THEREAFTER. THIS PRODUCT WITH
è
THIS COASTLINE DATA CARD
DOES NOT REPLACE THE
REQUIREMENT TO USE THE
APPROPRIATE PRODUCTS FOR
NAVIGATION ACCORDING TO
NATIONAL AND INTERNATIONAL
REGULATIONS.
PROGRAM No. 03591730**
Product information Startup test Chart disclaimer
The magnetron in the antenna unit takes about one minutes and thirty seconds
to warm up before the radar can be operated. The time remaining for warm up of
the magnetron appears at the center of the display, counting down from 1:30 to
0:01.
You m ay press any key at the chart disclaimer screen to show the last-used
display, or wait several seconds to let the equipment do it for you.
To turn the unit off, press and hold down the [POWER/BRILL] key until the
screen goes dark (approx. 3 sec.). To protect the LCD attach the hard cover.
Note that the network sounder will be turned off approx. three minutes after
turning off the power.
Note: You are asked if you want to start the simulation mode, which provides
simulated operation of the equipment, the f irst time you turn on the power
(or any time power is applied after a memory reset) the message shown
below is displayed. Push the [ENTER] knob to start the simulat ion mode,
or press the [CLEAR] key to start normal operation. For further details
about the simulation mode, see the paragraph “1.9 Simulation Display.”
START
SIMULATION MODE?
YES ... PUSH ENTER KNOB
NO ... PUSH CLEAR KEY
TO SKIP.
1-7
1. OPERATIONAL OVERVIEW
1.4 Cursor Pad, Cursor
The cursor pad mainly functions to shift the cursor, for measurement of range
and bearing to a location (radar) and latitude and longitude position (plotter).
Operate the cursor pad to shift the cursor. The cursor moves in the direction of
the arrow or diagonal pressed, on the cursor pad.
For the plotter display, the cursor can be turned off with the CENTER sof t key.
This also returns own ship marker to the screen center.
Cursor
.125nm
SP
.250/ 319.9
M
°
H-UP
SIGNAL
PROC
RADAR
DISPLY
NAV
FUNC
TARGET
ZOOM &
D. BOX
359.9°R
+
0.24nm
Radar display
Cursor, cursor data
Cursor data
L/L position,
Range and
bearing from
own ship to
cursor
Cursor
34° 22. 3456'N 272.4°M TRIP NU
+
080° 22. 3456'E
15.9 nm 99.9 nm
16.0nm
Plotter display
MARK
ENTRY
MODE
NTH UP
CENTER
GOTO
CURSOR
D. BOX
ON/ OFF
1-8
1. OPERATIONAL OVERVIEW
1.5 Display Brilliance, Panel Brilliance, Contrast, Hue
You can adjust display brilliance, panel brilliance, contrast and hue
(MODEL1722C series only) as shown below.
1.5.1 Display brilliance, panel brilliance
1. Press the [POWER/BRILL] key mom entarily. A set of soft keys for
adjustment of brilliance, contrast and hue (MODEL172 2C series only) appear.
The last-used adjustment window appears. In the example below the display
brilliance adjustment window is shown.
Current selection is higtlighted.
.125nm
SP
.250/ 319.9
M
°
H-UP
DISPLAY BRILLIANCE
MODEL1722C series MODEL1722 series
8
2. Press the DI SPLY BRILL or PANEL BRI LL soft key as appropriate. An
adjustment window appears at the bottom of the screen. This window shows
the name of the it em selected for adjustment plus current brilliance level, by
bar graph.
BRILL
CONTST
DISPLY
BRILL
PANEL
BRILL
CONTST
/HUE
RADAR
STBY
RETURN
.125nm
SP
.250/ 319.9
H-UP
DISPLAY BRILLIANCE
Brilliance adjustment soft keys
°
8
CONTST
DISPLY
BRILL
PANEL
BRILL
CONTST
RADAR
STBY
RETURN
BRILL
M
DISPLAY BRILLIANCE
8
Display brilliance Panel brilliance
PANEL BRILLIANCE
8
Display brilliance and panel brilliance windows
3. Adj ust the [ENTER] knob, clockwise to raise the setting or counterclockwise
to decrease it. You may also use the soft key pressed at st ep 2, in which
case the item selected is adjust ed cyclically, from low to high. Eight levels of
display brilliance and panel brilliance are available.
4. Hit the RETURN soft key to finish.
The display brilliance can be adjusted by pressing the [POWER/BRILL] key.
If the unit is turned on with minimum display brilliance, press the
[POWER/BRILL] key consecutively to adjust the brilliance.
1-9
1. OPERATIONAL OVERVIEW
1.5.2 Contrast
1. Press the [ P OWER/BRILL] key momentarily.
2. Press the CO NTST (monochrome) or CONT ST/HUE (color) soft key.
3. For MODEL1722C series, two soft keys appear at the pressing of the
CONTST/HUE soft key: CONTST and HUE. Press the CONTST soft key to
adjust the contrast.
Contrast window
4. Adj ust the [ENTER] knob, clockwise to raise the setting or counterclockwise
to decrease it. You may also use the CONTST soft key, in which case the
item selected is adjusted cyclically, f r om low to high. 16 levels (monochrome)
and 10 levels (color) of contrast are available.
5. Press the RET URN soft key to finish.
1.5.3 Hue (MODEL1722C series)
CONTRAST
8
1. Press the [ P OWER/BRILL] key momentary.
2. Press the CONTST/HUE soft key.
3. Press the HUE soft key to show the hue setting window.
HUE
▲
¡
DAY
¡
NIGHT
¡
TWILIGHT
¤
MANUAL SET
▼
Hue window
4. Operat e the cursor pad or [ENTER] knob to select hue desired, referring t o
the table below. MANUAL SET follows the color settings on the RADAR
DISPLAY SETUP for the radar, CHART DETAILS menu for the plotter and
SOUNDER MENU for the sounder.
Day Night Twilight Applicable mode
Characters Black Red Green Plotter, radar, sounder
Radar ring Green* Red Green* Radar
Radar echo Orange Red Yellow Radar
Background White Black Blue Plotter, radar
Landmass Yellow Light Yellow Dim Yellow Radar
*: Red on C-map
5. Hit the RETURN soft key to finish.
Note: When using the overlay screen, the own ship track will be hidden if the
radar background and own ship track are blue and the “MANUAL” hue
setting is used. In this case, set HUE to other posit ion and then return to
“MANUAL” to show the own ship track in black.
1-10
1.6 Selecting a Display
1.6.1 Display modes
If you have a navigator and network sounder connected, four full-screen displays
are available: radar, plotter, and video sounder and navigation data.
(MODEL1722C series have five screens, those mentioned above plus the
overlay screen.) In addition to the full-screen display, you can divide the screen
into half-screen combination displays to show two sets of images (data).
1. OPERATIONAL OVERVIEW
Full screen
(Ex. radar)
Combination screen
(Ex. radar + sounder)
Overlay screen
(Radar and plotter,
color model only.
Requires L/L data)
Display screens
The table below shows the displays available with each screen type.
Screen type and available display screen
Full screen Combination screen
options
Radar, plotter, sounder,
nav data
Radar, plotter, echo
sounder, compass,
highway,
compass/highway, nav
data, overlay
Overlay screen options
(Color series only)
Radar + plotter
1-11
1. OPERATIONAL OVERVIEW
1.6.2 Selecting a display
1. Press the [ DISP] key to show the full-screen selection window. The icons of
modes not available are marked with “X” m ark. PAGE1-PAGE5 are
user-arrangeable displays called “hot pages,” which you can configure as you
like. For further details, see “5.5 Hot Page Set up.”
RADAR PLOT SNDR NAV OVRLY
PAGE1 PAGE2 PAGE3 PAGE4 PAGE5
Basic display
screens
Hot pages
· TURN KNOB TO SELECT MODE
AND PUSH KNOB TO ENTER.
· PUSH ANY SOFT KEY TO
SELECT IMAGE SOURCE.
Full-screen selection window (“overlay” for color model)
2. Rotat e the [ENTER] knob to select a basic display screen or a hot page
screen.
3. Push the [ENTER] knob. If you selected a basic display screen, a set of
combination display screens corresponding to the basic display screen that
was selected appear. In the example below, radar combination displays are
shown.
1-12
PUSH ENTER KNOB.
Radar combination screen selection window
4. Operate the [ENTER] knob to select the combination screen display desired
and push it to set.
1. OPERATIONAL OVERVIEW
1.6.3 Switching control in combination and overlay screens
A soft key is provided in relevant combination and overlay screens (color series
only) to switch control between displays. In the example below, the RADAR
CNTRL and PLOTTR CNTRL soft keys enable switching control between the
radar and plotter screens in the plotter/radar combination display.
3nm
12
LP
H-UP
ST-BY
34° 22. 3456'N 359.9°M TRIP NU
080° 22. 3456'E
16.0nm
19.9 kt 99.9 nm
SIGNAL
PROC.
RADAR
DISPL Y
NAV
359.9
+
FUNC
11.7nm
T ARGET
RADAR
CNTRL
CNTL
RADAR
RADAR
CNTRL
To adjust
plotter
°
R
PLOTTR
CNTRL
To adjust
3nm
12
LP
H-UP
ST-BY
34° 22. 3456'N 359.9°M TRIP NU
080° 22. 3456'E
16.0nm
19.9 kt 99.9 nm
359.9
+
11.7nm
radar
WP-002
FISH
WP-002
FISH
Radar display selected Plotter display selected
How to switch control between modes in the plotter/radar combination display
MARK
ENTRY
MODE
NTH UP
NAV
°
R
POS
PLOTTR
CCNTRL
1-13
1. OPERATIONAL OVERVIEW
1.6.4 Selecting radar source
When other network radar is connected to the equipment, you may select an
image source as shown below. This is not necessary when no other network
radar is connected. Select one host name for the source though there are two or
three radar units on the net.
Note: Turn the power off whenever changing the source.
1. Press the [ DI SP] key.
2. Press any sof t key to show the following display.
▲
RADAR SOURCE
RADAR
SOUNDER SOURCE*
SOUNDER
IP ADDRESS
HOST NAME
IF THERE IS MORE THAN
ONE NETWORK RADAR OR
ECHO SOUNDER, YOU MAY
SELECT THE IMAGE
SOURCES FOR DISPLAY.
- - -
-
172.031.003.001
RADAR
- - -
*: Do not change this setting.
SELECT
SOURCE
EDIT
RETURN
Select source menu
3. Use the cursor pad t o select RADAR SOURCE and press the EDIT key.
RADAR SOURCE
1-14
RADAR
- - -
Radar source
Radar source and sounder source windows
4. Use the cursor pad and [ENTER] knob to enter source host name: ◄ or ► to
select position and rotate the [ENTER] knob to select character.
5. Press the [ E NTER] soft key or [ENTER] knob.
6. Confirm that t he correct host name is entered.
7. Press the [DISP] key to finish.
8. Turn the power off and on again.
Note: Sources names are determined at installation. For example, the source
names for radars in a two radar system might be “RADAR” and
“RADAR1”.
1.7 Data Boxes
Data boxes, providing navigation data, may be shown on any full-screen display.
Up to six data boxes (two in case of large characters) may be shown, and the
default data boxes are position (in latitude and longitude), course over ground,
speed over ground, trip log and cursor position. The user may choose which
data to display, where to locate it, and show or hide it as desired. In addition,
data boxes may be set independently for each display mode (radar, plotter,
sounder). For how to select data for the data boxes, see paragraph “5.5 Data
Boxes Setup”.
1. OPERATIONAL OVERVIEW
.125nm
SP
.250/ 319.9
M
°
H-UP
MARK
ENTRY
MODE
NTH UP
NAV
POS
TRIP LOG
177
POSITION
°
47
58.535'N
°
122
36.496'W
nm
COG
323.6
°
M
SOG
D.BOX
ON /OFF
20.0
350.4
0.000 nm
kt
°
Data boxes
Plotter display, showing data boxes
1.7.1 Showing, hiding data boxes with soft key
D. BOX ON/OFF (EBL/VRM data box, cursor data
Radar: ZOOM & D. BOX
→
box also shown/hidden)
Plotter: D. BOX ON/OFF
D. BOX ON/OFF
Sounder: AUTO/D. BOX
→
1.7.2 Rearranging data boxes
M
You may select the location for data boxes as follows:
1. Using the cursor pad, move the cursor to the data box you wish to move. As
the cursor enters the box it changes to a hand. Push the [ENTER] knob, and
the hand changes to a fist, meaning the box is correctly selected.
2. Use the cursor pad to drag the data box to the location desired and push the
[ENTER] knob.
1.7.3 Temporarily erasing a data box
You may temporarily erase a data box. Use the cursor pad to place the cursor
inside the data box you wish to erase and press the [CLEAR] key. To redisplay
the box, press the ZOOM & D.BOX soft key D.BOX soft key to display it.
1-15
1. OPERATIONAL OVERVIEW
1.8 Function Keys
The function keys provide for one-touch call up of a desired function. The default
function key settings are as shown in the table below.
Default Setting, Key Label Function
Key
Radar Plotter Echosounder
#1 Heading line on/off,
HL
#2 Rings on/off, RNG Edit mar k/line, EML Clutter, CLT
#3 Echo trail, TRL Ruler, RUL Signal level, SLV
#4 Offcenter, SFT Add new waypoint,
#5 Radar source, RSR Waypoint
1.8.1 Executing a function
1. Press the [ HIDE/SHOW] key to replace the preset soft key labels with the
function key labels.
.125nm
SP
.250/ 319.9
H-UP
°M
TARGET
H
L
R
N
G
T
R
L
S
F
T
R
S
R
Function
keys
Track on/off, TRK TLL output, TLL
Noise limiter, NL
ADD
Picture advance, PA
alphanumeric list,
ALP
34° 22. 3456'N 359.9°M
080° 22. 3456'E
19.9 kt 99.9 nm
TRIP
NU
16.0nm
T
R
K
E
M
L
002WP
FISH
BRIDGE
R
U
A
L
p
L
A
D
D
Function
keys
1-16
359.9°R
+
0.24nm
Radar
Plotter
Function keys
2. Press function key desired.
Note: Function keys can be individually programmed f or the radar, plotter and
sounder displays. For further details see the following:
Radar: paragraph 5.2.3
Plotter: paragraph 5.3.2
Sounder: paragraph 5.9.4
Loading...