Furrion FEHS32V7A User Manual

USER’S MANUAL

LED TV SET

3

2” HD LED TV FEHS32V7A

1

Contents

 Introduction
 Warning
 Caution
 Main Unit Description
 Remote Control
 OSD basic adjustment
 ATSC Features
 USB Features
 Specifications

 Trouble Shooting

2

Introduction

Thank you very much for your purchase of our product of LED TV. It serves as a normal color

TV and PC monitor. To enjoy your set to the full from the very beginning, read this manual

carefully and keep it handy for ready reference.

INSTALLATION

① Locate the receiver in the room where direct light does not strike the screen. Total darkness or

a reflection on the picture screen can cause eyestrain. Soft and indirect lighting is recommended

for comfortable viewing.

② Allow enough space between the receiver and the wall to permit ventilation.

③ Avoid excessively warm locations to prevent possible damage to the cabinet or premature

component failure.

④ This TV receiver can be connected to AC100-240V 50/60HZ.

⑤ Do not install the receiver in a location near heat sources such as radiator, air ducts, direct

sunlight, or in a place somewhere like close compartment and close area. Do not cover the

ventilation openings when using the set.

⑥ The indicator light will last about 30 seconds to go out after cutting off the electricity, during

this period, you cannot repower it on until the indicator light goes out. Thanks a lot for your

attention!

3

Warning

This symbol is intended to alert the user to avoid the risk

of electric shock, do not disassemble this equipment by anyone

except a qualified service personnel.

This symbol is intended to alert the user to the presence

of important operation and maintenance instructions in

the literature accompanying the equipment.

Class I structures of equipment should be connected to the

grid power output with a protective earth connection on the
socket. Power plug as a broken appliance，broken

installations should be easy to operate.

CAUTION: TO AVOID THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK).

NO USER- SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

4

Caution

Caution

High voltages are used in the operation of this product.

- Do not remove the back cabinet from your set. Refer

servicing to qualified service personnel.

Caution

To prevent fire or electrical shock hazard, Do not expose

the main unit to moisture, do not place objects filled with liquids,

such as vases, on the apparatus.

Caution

Do not drop or push objects into the television cabinet

slots or openings. Never spill any kind of liquid on the

television receiver.

Caution

Avoid exposing the main unit to direct sunlight and other

source of the heat. Do not stand the television receiver

directly on other produces which give off heat. E. g. video

cassette players, Audio amplifiers. Do not block the

ventilation holes in the back cover. Ventilation is essential

to prevent failure of electrical component. Do not squash

power supply cord under the main unit.

5

Caution

Caution

Never stand on, lean on, push suddenly the product

or its stand. You should pay special attention to

children.

Caution

Do not place the main unit on an unstable cart stand,

shelf or table. Serious injury to an individual, and

damage to the television, may result if it should fall.

Caution

When the product is not used for an extended period

of time, it is advisable to disconnect the AC power

cord from the AC outlet.

Caution

The LCD panel used in this product is made of glass.

Therefore, it can break when the product is dropped

or applied with impact. Be careful not to be injured

by broken glass pieces in case the LCD panel breaks.

6

Main unit description

Control Panel Button Function

TV Terminal Connections

1. Coaxial out terminal.

2. RF antenna.

3. VGA input terminal of simulation signal of PC.

4. PC AUDIO input terminal.

5. Video input terminal.

6. AUDIO input terminal.

7.Component input terminal.

8. HDMI1 input terminal.

9. HDMI2 input terminal.

10. HDMI3 input terminal

11. Line out terminal.

12. EARPHONE out terminal.

13. USB input terminal.

VOL+ : Volume up.
VOL- : Volume down.
CH+ : TV channel up.
CH- : TV channel down.
MENU : Press to select the main menu.
TV/AV : Select the input signal.
POWER : Switch on when at standby mode or enter the standby mode.

7

8

9

Remote control

POWER: Power on/off button, press once to turn the TV on and press

again to turn the TV off.

MUTE: Press this button to mute or restore sound.
MTS/AUDIO: When stereo program is received, press this key to

switch sound system between mono and stereo.
When SAP program is received, press this button to switch sound
system between mono and SAP
When stereo and SAP program is received, press this key to switch
among mono, stereo and SAP.
Press this key to show the list of audio languages available for the
current channel in ATSC

ASPECT: Press to adjust picture ratio.
PMODE: Select picture mode.
SMODE: Select sound mode.
0-9: Select and switch to a channel using 0 - 9.

-/--: Switch the program digit.

: Switch back and front between the current and previous channels.

DISPLAY: Display TV information.

EPG：Enter electronic program guide

AUTO: Adjust the picture automatically in pc mode.
RED, GREEN, YELLOW, CYAN: This button is not available.
SLEEP: Set the sleep timer.

SOURCE: Press to change signal source.
ENTER: Enter the selected option or perform the selected operation.
MENU: Press this button to enter the main menu.
EXIT: Exit the OSD (On-screen display).
CH+/CH-: Change the channel.
CC: Press this key to select the CC ,ON or OFF mode
INFO: Display some information of current program in TV mode.
VOL+/VOL-: Adjust the volume.
FAV: Switch between custom set "Favorite List"
F.LIST: Press this key to display the Favorite List mode.
C.LIST: Press this key to display the channel list mode.

10

Installation Guide

Press MENU button to display the MAIN OSD MENU; Press ◄ / ►button to select the MENU you

want; Press ENTER button to enter the sub menu; Press ▼ / ▲ button to select the option and then press
◄ / ► to adjust the value in the sub menu; You can press MENU button to go back to the upper menu or

EXIT button to close the OSD.

PICTURE

Press ENTER when the Picture Settings item is highlighted. Then you will go to the sub-menu as
following.
Press ▼ / ▲ to select the desired menu item. Press ENTER to proceed if necessary.
Press ◄ / ► to adjust the item the desired level.
When you have changed the settings, you can exit from the menu by pressing MENU.

Picture Settings

Press ▼ / ▲ button to select Picture Settings, then press ◄ / ► button to adjust. Only in the User mode,
the detail options as following can be adjusted.

11

Press ▼ / ▲ button to select Brightness, then press ◄ / ► button to adjust. . Press ▼ / ▲ button to
select Contrast, then press ◄ / ► button to adjust. . Press ▼ / ▲ button to select Color, then press ◄ /
► button to adjust. . Press ▼ / ▲ button to select Tint, then press ◄ / ► button to adjust. Press ▼ / ▲
button to select Sharpness, then press ◄ / ► button to adjust. .

Screen Size

Press ▼ / ▲ button to select Screen Size, then press ◄ / ► button to adjust.

PC Settings

Note : The pc settings only in pc mode

.Press ENTER when the PC Settings item is highlighted. Then you will go the sub-menu as
following.
.Press ▼ / ▲ to select the desired menu item. Press ENTER to ▼ / ▲ proceed if necessary.
.Press ◄ / ► to adjust the item to the desired level.
.When you have changed the settings, you can exit from the menu by pressing MENU.
Press ▼ / ▲ button to select Auto Adjust, then press ENTER button to start auto adjusting.
Press ▼ / ▲ button to select Horizontal Position, then press ◄ / ► button to adjust.
Press ▼ / ▲ button to select Vertical Position, then press ◄ / ► button to adjust.
Press ▼ / ▲ button to select Clock, then press ◄ / ► button to adjust.
Press ▼ / ▲ button to select Phase, then press ◄ / ► button to adjust.

12

Press ▼ / ▲ button to select Reset, then press ENTER button to reset the options above.

Color Temperature

Press ENTER when the Color Temperature item is highlighted. Then press ◄ / ► button to adjust.

Advanced Picture Settings

Note: This option in the PC mode no role!

Dynamic Contrast
Press ▼ / ▲ button to select the item Dynamic Contrast, then press ◄ / ► button to adjust. It can
adjust the contrast

Film Mode Press ▼ / ▲ button to select the item Film Mode, then press ◄ / ► button to adjust. Noise
Reduction

Press ▼ / ▲ button to select the item Noise Reduction, then press ◄ / ► button to adjust.
MPEG Noise Reduction
Press ▼ / ▲ button to select the item MPEG Noise Reduction, then press ◄ / ► button to adjust. It can
improve the quality of the pictures by reducing the block noise.

13

SOUND

Sound Settings

Press ENTER when the Sound Settings item is highlighted. Then you will go to the sub-menu as

following.

Press ▼ / ▲ to select the desired menu item. Press ENTER to proceed if necessary.

Press / to adjust the item the desired level.

When you have changed the settings, you can exit from the menu by pressing MENU.

Bass

Press ▼ / ▲ button to select the item Bass, then press ◄ / ► button to adjust.

Treble

Press ▼ / ▲ button to select the item Treble, then press ◄ / ► button to adjust.

Balance

Press ▼ / ▲ button to select the item Balance, then press ◄ / ► button to adjust.

14

Surround Mode

Press ▼ / ▲ button to select the item Surround Mode, then press ENTER button to adjust.

AVL

Press ▼ / ▲ button to select the item AVL, then press ENTER button to adjust.

Analog Sound

Press ▼ / ▲ button to select the item Preferred Analog Sound, then press ◄ / ► button to select

the prefer audio

Digital Sound

Press ▼ / ▲ button to select the item Preferred Digital Sound, then press ◄ / ► button to select the

prefer audio

Digital Audio output

Press ▼ / ▲ button to select the item Digital Audio output, then press ◄ / ► button to select the
Audio output mode.

Equalizer Settings

Press ▼ / ▲ button to select the item Equalizer Settings, then press ◄ / ► button to select the

desired mode.

CHANNEL MENU

Note: This menu is only shown when the input source is TV.

15

Channel List

Press ▼ / ▲ button to select Channel List, then press enter scan the Channel List. If you select the

press enter button to option “In Channel List” On, the channel label will display in the list.

Favorite List

Press ▼ / ▲ button to select Favorite List, then press ENTER button to scan the Favorite Channel

List.

Channel Setting

Press ▼ / ▲ button to select Manual Channel Setting, then press ENTER button to set the value in

the sub menu.

16

Skip

Set the channel to be skipped when using CH+/Ch- to view channels.

Favorite

Set the channel to your favorite list.

Label

Rename label of the channel.

Signal Type

Press ▼ / ▲ button to select Signal Type, then press button ◄ / ► to select the type you want to set.

There are two selections: Air and Cable.

Auto Channel Search

Press ▼ / ▲ button to select Auto Channel Search, then press ENTER button to search channel.

A Channel Search Menu will appear as below.

17

PARENTAL CONTROL

Input password to enter, default password is “0000”.

V-CHIP

Press ▼ / ▲ button to select V-CHIP, then press ENTER button to adjust. A Sub Menu Will appear

as below.

18

US V-CHIP

Press ▼ / ▲ button to select US V-CHIP, then press ENTER button to adjust. A Sub

Menu Will appear as below.

Movie Rating

Press ▼ / ▲ button to select Movie Rating, then press ENTER button to adjust. A Sub Menu Will

appear as below. Press ▼ / ▲ button to select Rating, then press ENTER button to lock

TV Rating

Press ▼ / ▲ button to select TV Rating, then press ENTER button to adjust. A Sub Menu will

appear as below.

Press ▼ / ▲ / ◄ / ► button to select Rating, then press ENTER button to lock.

19

CANADA V-CHIP

Press ▼ / ▲ button to select CANADA V-CHIP , then press ENTER button to adjust.

A Sub Menu Will

appear as below.

The operation of CANADA V-CHIP is the same as the operation of US V-CHIP.

Block Unrated Show

Press ▼ / ▲ button to select Block Unrated Show, then press ENTER button to set the rating

locked.

Downloadable Rating

Press ▼ / ▲ button to select Downloadable Rating, then press ENTER button to set the rating. If

20

the DTV program doesn’t have this rating information, this option will be in gray.

Clear Downloadable Data

Press ▼ / ▲ button to select Clear Downloadable Data, then press ENTER button to set the

rating.

Note: The above two operation only valid when playing the downloadable data stream. The

operations are the same as US V-CHIP.

CHANGE PASSWORD

Press ▼ / ▲ button to select Change Password, then press ENTER button to adjust the value.

A Sub Menu Will appear as below. If the password is changed, all of the passwords in the menu will

be changed at the same time.

Note: If you forget your password, you can use “1470” to enter any menu locked.

Keypad Lock

Press ▼ / ▲ button to select the item Keypad Lock, then press ENTER button to adjust.

Source Lock

Press ▼ / ▲ button to select Source Lock, then press Enter button to enter the sub menu. Press ▼

/ ▲ button to select Source, then press ENTER button to set the Source Lock. You can’t enter the

locked source if you set the source lock.

21

Setup Menu

Closed Caption

Press ▼ / ▲ button to select the item Closed Caption, then press ◄ / ► button to adjust.

22

Caption Display

Press ▼ / ▲ button to select Caption Display, then press ◄ / ► button to select ON or OFF.

Analog Caption Type

Press ▼ / ▲ button to select Analog Caption Type, then press ◄ / ► button to select the type.

Digital Caption Type

Press ▼ / ▲ button to select Digital Caption Type, then press ◄ / ► button to select the type.

Digital CC Preset

Press ▼ / ▲ button to select Digital CC Preset, then press ◄ / ► button to select Default or

Custom.

Digital CC Style

This menu is only shown when the Digital CC Preset is selected Custom.

CC Size

Press ▼ / ▲ button to select CC Size, then press ◄ / ► button to set.

CC Font

Press ▼ / ▲ button to select, then press ◄ / ► button to select the Font.

23

CC Opacity

Press ▼ / ▲ button to select CC Opacity, then press ◄ / ► button to select the Opacity.

Text Color

Press ▼ / ▲ button to select Text Color, then press ◄ / ► button to select the color.

CC Background Opacity

Press ▼ / ▲ button to select CC Background Opacity, then press ◄ / ► button to select the Opacity.

CC Background Color

Press ▼ / ▲ button to select CC Background Color, then press ◄ / ► button to select the Color.

Menu Language

Press ▼ / ▲ button to select the item Menu Language, then press ◄ / ► button to adjust.

Clock

Press ▼ / ▲ button to select the Clock, then press ENTER to edit.

Time Zone

Press ▼ / ▲ button to select Timer Zone, then press ◄ / ► button to set.

Auto Clock

Press ▼ / ▲ button to select the item Auto Clock. then press ENTER button to adjust.

Setup Time

Press ▼ / ▲ button to select Setup Time, then press ◄ / ► button to adjust the time and use the

ENTER button to go to the next option.

Day Of Week

This option displays the Day Of Week corresponding to the setup time.

Daylight Saving Time

Press ▼ / ▲ button to select the item Daylight Saving Time. then press ENTER button to adjust.

24

OTHERS MENU

Blue Back

Press ▼ / ▲ button to select Blue Background, then press ENTER button to select when there is no

signal, whether set the background in blue or not.

No Signal Power Off

Press ▼ / ▲ button to select No Signal Power Off, then press ENTER button to select it On or Off.

When set it on, if there is no signal input, it will go into standby.

No Operation Power Off

Press ▼ / ▲ button to select No Operation Power Off, then press ENTER button to select it On or

Off. When set it on, if there is no operation, it will go into standby.

All Reset

Press ▼ / ▲ button to select All Reset, then press ENTER button to execute reset. When you select

All Reset item, a dialogue box will appear as following

25

USB Features

Connect the USB and press the source button, select “Media” by“/”button, then press “ENTER”

button to enter USB mode.

Music

Press“/”button to select the music menu, and press “ENTER” button to enter.

Press the “/” button to select the drive disk you want to watch, and press “ENTER”
button to enter.
Press the “/,/” button to select the file you want to Listen in the file selecting menu,

then press “ENTER” button to play.

Press Source button to change to other signal channel.

When play the music: Press “VOL/VOL “button to adjust the volume size, and
press“/”button to select the play previous chapter、Pause、next chapter、Stop， Press “ENTER”
button to confirm。

Note: Music just can support MP3 format.

Photo

Press“/” button to select the Photo menu, and press “ENTER” button to enter.

Press the “/” button to select the drive disk you want to watch, and press “ENTER”

button to enter.

Press the “EXIT” button to select return option to go back to the previous menu.

26

Press the“/” button to select the file you want to watch in the file selecting menu, then

press “ENTER” button to display picture.

When you select the drive disk, you can press“/”button to select “Open”、“ Thumbnail”or
“Slideshow”, Then press“ENTER” button to enter. Press Source button to change to other signal

channel.

Note: Picture just can support JPG format.

Media Setting

Press“/”button to select Media Setting menu, Then press“ENTER” button to enter..

Press“” button to select Slideshow Interval and Press“/”button to adjust the Interval

time.

Press “/” button to select Slideshow Effect and Press“/”button to adjust Effect mode.
Press“/” button to select Slideshow Repeat and Press“/”button to select Off、On.

Press“/” button to select Music Play Mode and Press“/”button to adjust satisfying

Play Mode.
Press“/” button to select Music Play Repeat and Press “/”button to select Off、On.
Press“/” button to select Music Auto Play and Press“/”button to select Off、On.

NowPlaying

Press“/”button to select NowPlaying menu, Then press ENTER button to the Playing file.

Note：

① Non-support the HDD, just support less than 4G USB.
② MAX current is not more than 500mA.
③ Non-support the video file to play.
④ This feature picture is only for reference, actual item is to the standard.

Note: The pictures about function are provided for reference only which will be in

accordance with exact circumstances.

27

RGB INPUT

Model

Resolution

Horizontal Frequency(KHz)

Vertical Frequency(HZ)

DOS

720x400

31.5

70

VGA

640x480

31.5

60

SVGA

800x600

37.9

60

XGA

1024x768

48.4

60

WXGA

1360x768

47.7

60

HDMI INPUT

Mode Resolution

Horizontal Frequency

(KHz)

Vertical Frequency

(HZ)

480i

720 x480i

15.73

59.94/60

480p

720 x480p

31.47

59.94/60

720p

1280 x 720p

37.50 44.96

50 59.94/60

1080i

1920 x 1080i

28.13 33.75

50 59.94/60

1080p

1920 x 1080p

56.25 67.5

50 59.94/60

COMPONENT INPUT

Model

Resolution

Horizontal Frequency

(KHz)

Vertical Frequency

(HZ)

480i

720 x480i

15.73

59.94/60

480p

720 x480p

31.47

59.94/60

720p

1280 x 720p

37.50 44.96

50 59.94/60

1080i

1920 x 1080i

28.13 33.75

50 59.94/60

1080p

1920 x 1080p

56.25 67.5

50 59.94/60

28

Before consulting service personnel, check the following chart for possible solutions.

PROBLEM

SOLUTION

TV will not turn on

●Make sure the power cord is plugged in. ●The batteries

in the remote control may be Exhausted; replace the

batteries.

No picture, no sound

●Check the cable between TV and antenna/ external AV

device. ●Press the power button on the remote. ●Press the

SOURCE button the remote, then press the “▲/▼”button

repeatedly to select the TV source.

Poor picture, sound OK

●Check the cable between TV and antenna/ external AV

device. ●Try another channel, the station may have

broadcast difficulties. ●Adjust the brightness/contrast in

the Video menu. Check that the unit is set to NTSC.

Audio noise

●Move any infrared equipment away from the TV.

The TFT LED panel uses a panel consisting of sub pixels which requires sophisticated
technology to produce. However, there may be a small number of bright or dark pixels on the

screen. These pixels will have no impact on the performance of the product.

29

Furrion Warranty

Congratulations on your purchase of a Furrion product. All Furrion products are made
to stringent quality standards and if used properly for their intended purpose you should
enjoy many years use from your purchase.
We are pleased to provide you with a 1 year warranty on all Furrion products. The
details of this warranty are set out in the terms and conditions (see below) which
supplement the authorized dealer’s Terms and Conditions of Sale.
This warranty is given in addition to your other rights under the laws of United States.
Warranty Terms and Conditions

1. The warranty guarantees that Furrion products will be free from faults or defects in
workmanship and materials for a period of 1 years commencing on the date o f
delivery to you. If a valid claim is made under warranty then you will only be
entitled to claim in accordance with paragraph 6 below.

2. The warranty only applies:

a. to Furrion products with a valid serial number
b. to the person who purchased the Furrion product. It is not transferrable to any other
person;
c. to individuals who purchased the Furrion products as a consumer for private use, not

to businesses, companies, partnerships or sole traders;

d. to Furrion products used solely within a domestic environment for personal use, not

to Furrion products put into and used within business premises, place of work, rental

properties, student properties or similar;
e. to Furrion products used within the environment intended by their design
f. to Furrion products used and installed in accordance with the instructions supplied

with the product;

g. where the purchaser of the Furrion product has validated the warranty in accordance
with paragraph 4 below;
h. to Furrion products purchased and used within the United States.

3. The warranty does not cover:

a. items where the serial number has been defaced and/or rendered unidentifiable;
b. damage caused or contributed to by poor, faulty or incorrect use, installation or
maintenance;
c. damage caused or contributed to by events outside Furrion’s control including but

not limited to Acts of God, fire, explosion, contact with corrosive matter, extreme
weather conditions, flood, vandalism, soiling, misuse, abrasion, improper storage
following delivery, rot and/or infestation following delivery, leaks (or similar
incidents), damage due to non-domestic use;

d. damage or deterioration caused or contributed to as a result of normal wear and tear;
e. damage caused or contributed to by maintenance or repairs other than those carried
out by an authorized dealer;
f. damage caused or contributed to by willful damage, abuse, mistreatment, negligence,

abnormal storage or environmental conditions;

g. damage caused or contributed to by household animals and misuse by children.

30

4. To validate the warranty you must:

a. fill in the registration card provided with the Furrion product; and
b. register the warranty covering the Furrion product within 6 months of delivery of

the Furrion product by following the instructions on the registration card.

5. To make a claim under your warranty you must contact Furrion’s customer service
at [e-mail] or the address on your warranty card.

6. Following the filing of a claim, Furrion will investigate the claim and if we believe
there is a defect or fault covered by the warranty, we will at our option either repair
the defective Furrion product (or part), replace the defective Furrion product (or
part), or issue a refund of the price you paid for the product.

7. Please note in the event that no fault can be found, it is your responsibility to pay for

the re-delivery of the replacement items.

8. Installation of any repaired or replacement Furrion product will not be Furrion’s

responsibility.

9. If you do not allow the authorized dealers representative to view the Furrion product
which is the subject of the warranty claim, you will invalidate the warranty in
respect of that claim.

10. Any repaired or replacement Furrion product parts shall be guaranteed on the terms
of this warranty for the unexpired portion of the warranty period only.

11. This warranty is non-transferrable and is personal to the original purchaser as shown
on the invoice.

12. This warranty is subject to the jurisdiction of the courts of USA, and any

dispute or claim arising out of, or in connection with it or its subject matter, shall be
governed by, and construed in accordance with United States of America law.

Furrion.com