Furrion FCE48TASL, FCN48TASK, FCE48TASH Installation Manual

Side Cameras & Rear Camera

FEMALE CONNECTOR, MALE PINS

withMarker Light

Installation Guide

Models: FCE48TASL

FCN48TASK

FCE48TASH (LED)

This Installation Guide will help you install and adjust the camera properly.

Please visit: https://furrion.

com/collections/cameras/

products/vision-s-7-four-

camera-observation-system

and find out more on the

HowtoVideo section.

For further support and to

download the complete user

manual please visit:

https://furrion.com/pages/

download-navigation

Prepare

1. Ensure that all items in your package match those shown in the ‘What’s in the box’ section on the packaging box.

2. Before installation, please read and understand all the important safety-related instructions from the online user manual.

3. Prepare tools you may need, including # 1 and #2 Phillips head screwdrivers, sealant, insulation tape, pencil and/or a 5/8”hole saw (needed only when drilling a new hole).

Mount Marker Light

Note: Skip this section if your RV is pre-installed with a bracket for camera installation.

IMPORTANT: Before any installation and wiring operation, remove the key from the ignition and isolate the 12V / 24V power source.

Always seek professional assistance if you are unsure about the installation and wiring operation.

1. Determine the mounting location on your RV. Ensure that there is no obstacle blocking the camera view. To avoid drilling new holes, you are recommended to replace the original marker lights with Furrion products directly as shown below:

− For rear camera position: Location of the original rear marker light at the top center on the rear of your RV. To accommodate the camera, ensure that there is at least 7.5” space between the central points of the two adjacent marker lights.

− For side camera position: Location of the original side marker lights (as front as possible & the height from ground to the middle of the trailer).

Note: The fifth-wheel shown below is for referenceonly. You can mount Furrion Vision S products onto various types of long vehicles such as travel trailer or ClassA/B/C motorhomes.

Rear camera

position

Side camera

position

2. Remove the lens cover and detach the camera from the marker light bracket (right side camera shown).

#1 Phillips head

#4x1/4" self-tapping

3. Remove the original marker light from the corresponding location.

4. Connect the bare ends of the power cable on the back of the bracket to the nearest 12V / 24V power supply:

Red (V+_Camera): to the positive wire of the running light circuit; Black (GND): to ground; Yellow (Trigger): to left/right turn signal [only available for LED versions]; Brown (V+_Lamp): to positive wire of the running light circuit;

Example of a typical 7-way connection

Tail lights/running lights

Trigger Signal

Note: This image is only for identifying the color code of the signal wires and the user does not have to route the trigger wires to 7-way.

(Brown)

Left turn signal &

brake light

(Yellow)

Ground (White)

Backup lights

Auxiliary 12v+/charging (Red)

Right turn signal & brake light (Green)

Trailer brake control (Blue)

Trigger Signal

Note: Ensure that the fuse on the connected power line provides additional 1A fusing current for the camera. Ensure proper cable isolation for all bare ends (e.g., by using insulation tape).

How to Video Full Manual Download

5. Secure the gasket and marker light bracket onto your vehicle using four flat head #6 x 3/4” self-drilling screws. If the mounting surface is uneven, apply sealant around the gasket for better sealing.

• For the rear camera, mount the antenna onto the camera securely and keep the antenna straight, adjust the view angle of the camera by rotating it upwards and downwards (0~50°) so that you can see the bottom edge of your vehicle and the road conditions behind.

Torque: ≤8 In-lbs

#2 Phillips head

#6x3/4" flat head

Mount Cameras (right side shown)

• Reattach the camera to the marker light bracket. Before fixing the camera, check its pairing status with the monitor by resuming power temporarily. Forincandescent lights, make sure the removable light bulb is properly installed before replacing the lens cover. Ensure that the lens on the camera face backwards after installation, with the MONITOR PAIRING button at the bottom. If you cannot find the video from the camera on the monitor screen or you have an unbundled camera, see the Quick Start Guide for the monitor or online user manual for pairing procedures.

#1 Phillips head

#4x1/4" self-tapping

Tip: See the complete user manual online for detailed functional explanations.

www.furrion.com/support

1-800-789-3341

support@furrion.com

Furrion Innovation Center & Institute of Technology

• 52567 Independence Ct., Elkhart, IN 46514, USA

trademarks licensed for use by Furrion Ltd. and registered

inthe U.S. and other countries.

Patents pending (FCE48TASL)

IG-FCM00009 V2.0