Please contact us if you need further assistance:
Tech support: tech@furiousfpv.com
Sales support: sales@furiousfpv.com
Website: http://furiousfpv.com/
RADIANCE DSHOT VERSION
Flight Controller
USER MANUAL VERSION 1.1
1
Contents
Change Log ........................................................................................................ 2
Introduction ....................................................................................................... 3
WHAT’S NEW RADIANCE DSHOT VERSION? ....................................................... 3
Features ............................................................................................................. 3
Connections ....................................................................................................... 5
Connect with Receiver .................................................................................... 5
Using SPD15 Receiver ............................................................................ 5
Using LR1000D Receiver ........................................................................ 6
Using XSR FrSky Receiver ....................................................................... 7
Using Spektrum Satellite Receiver ......................................................... 7
Connect with Video Transmitter ..................................................................... 8
Using Tramp HV ..................................................................................... 8
Using TBS Unify Pro ............................................................................. 10
Using FX FX799T .................................................................................. 12
Connect with stack Mnova and Runcam ...................................................... 14
Connect with other devices .......................................................................... 15
Connect with ESC 4 in 1 ................................................................................ 16
Using Aikon SEFM 30A ......................................................................... 16
Using Cicada 35x4 35A ......................................................................... 17
Using T-Motor F 35A 4IN1-4S .............................................................. 18
Basic setup ....................................................................................................... 19
Tips .................................................................................................................. 20
How to configure your Spektrum RX with your Flight Controller .................. 20
How to turn on bind mode ........................................................................... 22
Guideline configuration OSD with TRUE VISION CONFIGURATOR V1.0 ......... 23
How to open Piggy OSD menu by Transmitter .............................................. 24
2
Change Log
v1.1
Add guideline configuration OSD with TRUE VISION CONFIGURATOR V1.0
OSD Menu Index
3
Introduction
The Furious FPV Radiance FC (Flight Controller) provides a blaze of feature packed brilliance that
equates to the perfect fit for models utilizing their own PDB (power distribution board).
Functionality is the key, but innovation is our specialty. The Radiance FC stacks with 4 in 1 ESC’s
for perfect CG, allowing optimized acro flight. When utilising your own PDB, weight and cost are
minimised.
High performance and user friendly, the Radiance FC features cutting edge F3 chip (MPU6000)
processing power, a built in BEC, integrated LC filter, iLap transponder, and a current sensor
input, just to name a few. With this feature packed insanity, the Radiance shadows all other
FC's, providing everything that's needed in one perfect package.
Step into the light with unworldly levels of capability & functionality, all at ultra-budget friendly
pricing. Simply put, this is the way we do it at Furious FPV.
WHAT’S NEW RADIANCE DSHOT VERSION?
Remove PPM pin and add TX2 pin
Ready support ESC Dshot protocol
New component for BEC better
New red color for PCB
Features
Latest Generation F3 Processor Chip
High Performance, User Friendly F3 MPU6000 Chip
Integrated LC Filter for Perfect Clarity
Designed for Acro Precision via CG Perfection
Heavy Duty 1A BEC @ 5V Output and 0.8A BEC @12V Output
Included Spektrum Satellite Port
2S-5S Lipo Ready
Ready DSHOT protocol
Inrush Voltage Protection Input by Transient Voltage Suppressor
Gold Plated Pads for the Very Best Connectivity
Weight: 5gr
4
Board Layout
Dimensions
5
Connections
*WARNING: Radiance DShot Version can support up to 5s Lipo battery but make sure other
devices also support it.
Connect with Receiver:
Using SPD15 Receiver:
You can buy SPD15 Receiver right here: https://goo.gl/FTnrpR
6
Using LR1000D Receiver:
You can buy LR1000D Receiver right here: https://goo.gl/4Cr0Hl
* NOTE: If you use LR1000D Receiver please go to CLI and type the following commands:
set sbus_inversion = OFF
save
7
Using XSR FrSky Receiver:
Using Spektrum Satellite Receiver:
8
Connect with Video Transmitter:
Using Tramp HV:
With Piggy V2 OSD
9
With Only Camera
10
Using TBS Unify Pro:
With Piggy V2 OSD
11
With Only Camera
12
Using FX FX799T:
With Piggy V2 OSD
13
With Only Camera
14
Connect with stack Mnova and Runcam:
You can buy Mnova right here: https://goo.gl/JyQnds
15
Connect with other devices:
You can buy LED STRIP right here: https://goo.gl/TXwSwI
16
Connect with ESC 4 in 1:
Using Aikon SEFM 30A:
You can buy ESC Aikon SEFM 30 4 in 1 right here: https://goo.gl/IOYBEr
17
Using Cicada 35x4 35A:
You can buy ESC Sunrise Cicada 35x4 35A right here: https://goo.gl/s08OaI
18
Using T-Motor F 35A 4IN1-4S:
You can buy ESC F 35A 4in1-4S right hexre: https://goo.gl/QyM3eh
19
Basic setup
Please, follow carefully these next steps, and always remove your propellers when you’re
configuring your quad
STEP 1: Connect Radiance DS with the computer via USB cable and then open BetaFlight
STEP 2: Configure Ports.
(1) Turn on MSP of UART 1 to use OSD.
(2) Turn on Serial Rx of UART 2 to use Receiver Mode
(3) Select SmartPort of UART 3 to use S.Port of Receiver.
* NOTE: Please make sure that all the connections are correct.
STEP 3: Go to Configuration tab and choose ESC/Motor protocol in ESC/Motor Features
STEP 4: Select Serial- based receiver in Receiver Mode
20
If you are using SBus, iBus or a Spektrum Satellite, you will need to pick your Serial Receiver Provider.
Follow this table:
RX Type
Serial Receiver Provider
DSM2 1024bit/22ms
SPEKTRUM1024
DSM2 2048bit/11ms
SPEKTRUM2048
DSMX 1024bit/22ms
SPEKTRUM1024
DSMX 2048bit/11ms
SPEKTRUM2048
FrSky RX
SBUS
Futaba RX
SBUS
FlySky RX
IBUS
Turnigy RX
IBUS
Click “Save and Reboot”.
Tips
How to configure your Spektrum RX with your
Flight Controller
In Betaflight Configurator:
Go to the Ports tab
Enable “Serial RX” on the UART 2
Click “Save”.
21
Then go to the Configuration tab. Under the section labeled “Receiver”, pick Serial Receiver
Provider compare with your RX Type.
RX Type
Serial Receiver Provider
DSM2 1024bit/22ms
SPEKTRUM1024
DSM2 2048bit/11ms
SPEKTRUM2048
DSMX 1024bit/22ms
SPEKTRUM1024
DSMX 2048bit/11ms
SPEKTRUM2048
Click “Save”.
Finally, go to the Receiver tab. Pull down the drop down that says “Channel Map” and select
the “JR / Spektrum / Graupner” option.
Once again, click “Save”.
22
How to turn on bind mode
NOTE: Plug battery to the quad during setup.
Connect quadcopter to the computer and go to Command-line interface (CLI) tab.
Remember to type “save” and hit enter after these commands have been executed.
Type in the commands as pictured above, or copy and paste them from below:
set spektrum_sat_bind=9
set spektrum_sat_bind_autorst=0
save
NOTE – if you are using a DSM2 receiver, change “set spektrum_sat_bind=9” to
“set spektrum_sat_bind=5”
Reboot your Flight Controller by unplugging the Flight Controller from your PC then plugging
it back in.
Your RX should go into bind mode by now as the LED on the RX will be blinking rapidly.
23
Guideline configuration OSD with TRUE VISION
CONFIGURATOR V1.0
Serial Pass Through don’t need CLI in Betaflight
DOWNLOAD: Guideline install and configuration TRUE VISION CONFIGURATOR
STEP 1: Connect Radiance DS (connected with VTX/OSD) with PC via USB cable. Then plug
battery for FC.
STEP 2: Open True Vision Configurator on google chrome.
STEP 3: Please select Port COM (1) correlative with your device, then select UART 1 (2) using
for OSD.
STEP 4: Plug Battery for Radiance DS, then click Connect icon on True Vision interface to
connect and configuration OSD layout and setting.
STEP 5: After configuration device please click WRITE to save your configuration.
24
How to open VTX/OSD menu by Transmitter
To access the in-built OSD menu in MW-OSD, disarm your quadcopter first.
THROTTLE MIDDLE
YAW RIGHT
PITCH FULL
To navigate through menu in the OSD:
PITCH/ROLL sticks are used to
navigate
YAW stick is used to adjust /
change values
OSD Menu Index:
PID Config/Profile 1/2 or 3:
Roll/Pitch/Yaw PID for many flight modes
VTx Config:
Pit mode: On/Off
VTx Power: 25/200
VTx Shutdown: None/AUX1/AUX2/AUX3/AUX4
VTx Band: A/B/E/F/C/U/O/L/H
VTx Channel: 1/2/3/4/5/6/7/8
RC Tuning (RC Rate, RC Expo, Pitch/Roll Rate, Yaw Rate, TPA (Throttle PID Att),
Throttle Mid, Throttle Expo, TPA Breakpoint, Yaw RC Expo)
OSD Config (Display Main Volts, Display Amps, Display mAH, Display RSSI, Horizon,
Main Volts Alarm, mAH X100, Callsign)
Statsistics ( Fly Time, mAH Used, Max Amps, Voltage)
25
Thanks for using our product
Loading...