BELL 222
ENGINE SIZE:60
GENERAL INSTALLATION MANUAL
158mm
SAND AREA AS INDICATED BY ARROW ON THE FRONT PORTION WITH
#180 SAND PAPER. GLUE TAIL SECTION WITH 30MIN. EPOXY AND SET
TAIL HEIGHT AS SHOWN WITH INCLUDED PLYWOOD INDICATOR.
TAIL ATTACHMENT INSTRUCTION
GLUE SLOTTED BALSA AND VERTICAL FINS
IN HORIZONTAL STAB. AS SHOWN.
GLUE PLYWOOD JOINER INSIDE FUSELAGE.
BELL 222
ENGINE SIZE:60
GENERAL INSTALLATION MANUAL
2
4
5
7
3
1
6
8
CUT 2.5x11 MM SLOTS IN THE HATCH.
GLUE THE PLASTIC MOUNTING BRACKETS
INSIDE.
MOUNT THE SLOTTED PLASTIC PLATES
WITH 1.4x4 MM FLAT HEAD TAPPING SCREWS.
GLUE 3x16 MM PLYWOOD
IN THE FUSELAGE.
DRILL HOLES WHICH
ALIGNED TO THE ALUM.
POLES DIAGRAM. AS IN
CUT MESH ACCORDING TO THE TEMPLATE
PROVIDED. GLUE MESH WITH CA INSIDE
FUSELAGE AND TOP HATCH.
GLUE EXHAUST
ON FUSELAGE.
GLUE 3x10x10MM PLYWOOD AND 3 MM ALUM. POLES
FOR TOP HATCH AND FUSELAGE ALIGNMENT.
A
B
C
D
E
P.1
NOTICE: USE EPOXY UNLESS STATED.
SAND INSIDE FUSELAGE WITH #180 SANDING
PAPER BEFORE PARTS GLUING IN PLACE.
GLUE AND ALIGN HORIZONTAL STABS.
FASTEN TOP HATCH WITH 3 X 12 MM
SOCKET HEAD TAPPING SCREW
* "GOOP" IS A BRAND OF GLUE WHICH IS MANUFACTURED BY
ECLECTIC PRODUCTS, INC.
IT IS AVAILABLE IN MOST HARDWARE STORES.
CUT WINDSHIELD AND WINDOWS AS MARKED.
GLUE IN PLACE WITH SILICONE OR "GOOP" *.
INSERT TAIL BOOM INTO SPONGE RING
ENGINE SIZE:60
90
90
ALIGN HORIZONTAL STABS. TO FUSELAGE AS SHOWN.
10
12
14
16
9
11
13
15
GLUE 1.5x10x10 MM PLYWOOD.
MOUNT TAIL HATCH WITH M3x6
ROUND HEAD TAPPING SCREW.
GLUE CLEAR LIGHT, ALUM. HOLDER
AND STEEL WIRE IN THE TAIL FIN.
MOUNT THE VERTICAL FIN WITH
M3x16 ROUND SOCKET HEAD SCREWS,
3x8x0.7 WASHERS AND LOCKNUTS.
GLUE RED LIGHT ON TOP OF HATCH AND BOTTOM
OF FUSELAGE.
P.2
SIDE WINDOWS ARE
GLUED INSIDE FUSELAGE
BELL 222
GENERAL INSTALLATION MANUAL
BELL 222
ENGINE SIZE:60
INSTALLATION OF RETRACTABLE LANDING GEAR
P.3
OPTIONAL PARTS
RETRACT MECHANISM
PART NO. FK 9606
OPTIONAL PARTS
LANDING GEAR WIRE
PART NO. FK 9655
2 X 5 X 1.5
ALUM. WASHER
M2 X36
THREADED PUSH ROD
NOSE GEAR SERVO
BALL LINK
NOSE WHEEL 45 MM
MAIN WHEEL 45 MM
MOUNT THE SERVO TRAY
WITH M3 X 12 SOCKET HEAD
TAPPING SCREW
MAIN GEAR SERVO
BALL LINK
M2 X36
THREADED PUSH ROD
1
2
3
4
5
6
P.4
A
A
B
B
C
C
D
D
E
E
FOR BELL 222 (60)
(SCALE 1:1)
MESH TEMPLATE
INSTALLATION OF CENTURY PREDATOR MECHANISM
BELL 222
ENGINE SIZE:60
P.5
CUT VENTILATING HOLE AND MECHANISM
MOUNTING HOLES (3.5 MM) AS SHOWN.
CENTURY PREDATOR
MOUNTING MECHANISM IN
FUSELAGE WITH SHAPED
HARDWOOD IN PLACE.
10x50 MM PLYWOOD LOCATION
(INSIDE FUSELAGE)
CUT AWAY MARKED PORTION FOR SWATCH PLATE.
CUT HOLE FOR STARTING PROBE.
20 MM
CUT TAIL HATCH FOR GEAR-BOX AS SHOWN.
34 MM
43 MM
35 MM 65 MM 65 MM
60 MM
79 MM
50 MM
1
3
5
2
4
6
GLUE 10x50 MM PLYWOOD INSIDE FUSELAGE.
MOUNTING PLATE WITH M3x10 FLAT HEAD
SCREWS AND LOCK-NUTS.
ALUM.
17 MM
12.5 MM
203.5 MM
83.5 MM
8 MM
17 MM
65 MM
55 MM
HIROBO FREYA
CUT VENTILATING HOLE AND MECHANISM
MOUNTING HOLES (3.5 MM) AS SHOWN.
P.6
INSTALLATION OF HIROBO FREYA MECHANISM
BELL 222
ENGINE SIZE:60
SAND AWAY SHADED AREA ON PLYWOOD MOUNTING
PLATE AS SHOWN.
CROSS SECTION
MOUNT THE MECHANISM
IN FUSELAGE WITH SANDED
MOUNTING PLATE INVERTED.
CUT AWAY MARKED PORTION FOR SWATCH PLATE.
CUT HOLE FOR STARTING PROBE.
10x50 MM PLYWOOD LOCATION
(INSIDE FUSELAGE)
GLUE 10x50 MM PLYWOOD INSIDE FUSELAGE.
MOUNTING PLATE WITH M3x10 FLAT HEAD
SCREWS AND LOCK-NUTS.
ALUM.
CUT TAIL HATCH FOR GEAR-BOX AS SHOWN.
10 MM
38 MM
83.5 MM
1
3
5
2
4
6
CUT VENTILATING HOLE AND MECHANISM
MOUNTING HOLES (3.5 MM) AS SHOWN.
THUNDER TIGER RAPTOR
29 MM
212 MM
76.5 MM
20 MM
58 MM
50 MM
INSTALLATION OF THUNDER TIGER RAPTOR MECHANISM
P.7
BELL 222
ENGINE SIZE:60
SAND AWAY SHADED AREA ON PLYWOOD MOUNTING
PLATE AS SHOWN.
CROSS SECTION
MOUNT THE MECHANISM
IN FUSELAGE WITH SANDED
MOUNTING PLATE INVERTED.
CUT AWAY MARKED PORTION FOR SWATCH PLATE.
CUT HOLE FOR STARTING PROBE.
CUT TAIL HATCH FOR GEAR-BOX AS SHOWN.
10 MM
40 MM
RAPTOR 90 TAIL BOOM
LENGTH: 814 MM
(PART NO. PV-0422)
1
3
5
2
4
6
7
8
GLUE 10x50 MM PLYWOOD INSIDE FUSELAGE.
MOUNTING PLATE WITH M3x10 FLAT HEAD
SCREWS AND LOCK-NUTS.
ALUM.
BELL 222
ENGINE SIZE: 60
Below optional retractable landing gears
are available for this helicopter.
PARTS NO.
PARTS NO.
FK-9606
FK-9655
(1 helicopter needs 3 pcs)
(3 pcs per set)
Manufactured BY:
FUN-KEY AEROPLANE MODELS & BALSAWOOD MFR.
90
NOSE (1 PC)
95
MAIN (2 PC)
Loading...