Page 1
If channel 3 is already occupied for broadcasting,
1) Set your TV to channel 4.
2) Insert a pre-recorded tape into the VCR.
3) Press the PLAY button once.
4) After a few seconds, press the PLAY button
on the VCR for 3 seconds.
•
The RF output channel will change to channel 4 from channel 3 and you will
see a playback picture.
•
When a picture does not appear on the TV screen, repeat step [4].
5) Press the STOP button to stop playback.
You can use the AUDIO OUT jacks
and VIDEO OUT jack on the back of
the VCR if your TV has Audio/Video
Input jacks. In this case, you need to
set the TV to external Line Input Mode.
Please refer to your TV’s owner’s manual.
- 1 -
Owner’s Manual
Video Cassette Recorder
EWV603
If you need additional operating assistance after
reading this owner’s manual or to order replace-
ment accessories, please call
TOLL FREE : 1-800-256-2487
or visit our web site at http://www.funai-corp.com
0VMN03902 / HF440UD ★★★★★
Printed in China
ANT
AUDIO
VIDEO
IN
OUT
OUT IN
OUT
L
R
IN
ANT
AUDIO
VIDEO
IN
OUT
OUT IN
OUT
L
R
IN
AUDIO IN jacks
Connect the audio cables from the audio
out jacks of a camcorder, another VCR, or
an audio source.
VIDEO IN jack
Connect the video cable from the video out
jack of a camcorder, another VCR, or an
audio-visual source (laser disc player,
video disc player, etc.).
AUDIO OUT jacks
Connect the audio cables to the audio in
jacks of a camcorder, another VCR, a stereo
amplifier, or an audio system.
ANT IN jack
Connect your antenna or cable box.
ANT OUT jack
Connect the RF cable (supplied) to
the antenna input jack on your TV.
Front & Rear Terminals
Stereo TV Connection
ANT
IN
OUT
AUDIO
ANT
IN
OUT
VIDEO
OUT
L
R
IN
Connect
1
Audio/Video Cables
(not supplied)
LR
AUDIO OUTVIDEO
OUT
LR
AUDIO INVIDEO
IN
(Back of TV)
INOUT
(Back of VCR)
• Remote control
(NA372UD) with
Tw o AA batteries
• RF Cable
(WPZ0901TM002)
• Owner’s Manual
(0VMN03902)
Supplied Accessory
Installing the Batteries for
the Remote Control
Install two AA batteries
(supplied) matching the
polarity indicated on
the bottom of the
remote control.
Hint
Hint
• The RF output channel may
not change when you adjust
tracking during playback. In
this case, stop the playback,
and start the playback again.
After that, press the PLAY
button on the VCR for 3 seconds again.
VIDEO OUT jack
Connect the video cable to the video in jack
of a camcorder, another VCR, or a TV.
RF Output Channel
EMERSON AND THE G-CLEF LOGO ARE REGISTERED TRADEMARKS
OF EMERSON RADIO CORP., PARSIPPANY, NEW JERSEY, U.S.A.
MENU
CHANNEL
POWER
REC/
TAPE IN
VIDEO L-AUDIO-R
TIMER RECVCR/TVPOWER
1. Before using your VCR
ANT
IN
OUT
RF Cable (supplied)
(Back of VCR)
(Back of TV)
(Back of TV)
Plug the AC power cords of the VCR and TV into the AC outlets.
4
Disconnect
Antenna
or
2
Connect
3
Connect
Cable
Signal
Antenna
or
Cable
Signal
Basic VCR/TV Connection
Select this connection when you want to view or record a
scrambled channel.
With this connection, channels cannot
be changed on the VCR.You can view or record ONLY the
channels you have selected on the cable box or the satellite
box.
• While you are recording, only the recorded channel can
be viewed.
T
o select channels of the cable box or satellite box
1)Turn on the VCR by pressing the POWER button, and
then, press the VCR/TV button.The POWER and the
VCR/TV indicators on the front panel will light on. Then,
press the CHANNEL buttons to select channel 3 or 4
(the same channel as the output channel of the cable
box or satellite box).
• If you use the channel 4, you need to change the VCR’s
RF output to channel 4. Refer to “RF Output Channel”.
2) At the TV, select channel 3 or 4 (the same channel as
you have selected at step 1).
3) At the cable box or satellite box, select the channel you
want to view or record.
Select this connection when you want to change channels
on the VCR. With this connection, you may watch one
channel while recording another.
• You may not view or record a scrambled channel.
T
o select channels of the cable box or satellite box
1)At the cable box or satellite box, select channel 3 or 4
(the same channel as the VCR’s RF output channel.)
• Refer to “RF Output Channel”.
2)At the TV, select the same channel as the output channel (3 or 4) of the cable box or satellite box.
3)Turn on the VCR by pressing the POWER button, and
then, press the VCR/TV button .The POWER and
VCR/TV indicators on the front panel will light on. Then,
select the channel you want to view or record.
T
o play back a tape
Follow the steps 1) to 2) above. Then, play back a tape.
• Refer to “Playback” on page 5.
To view one channel while recording another
1)
While you are recording on the VCR, press the VCR/TV button so that the VCR/TV indicator disappears on the VCR.
2)At the cable box or satellite box, select the channel you
want to view.
Hint for Cable Box or Satellite Box
ANT
IN
OUT
RF Cable
(supplied)
(Back of VCR)
IN
OUT
E
(Back of TV)
Cable
Signal
Connection A
(Cable box or
Satellite box)
ANT
IN
OUT
RF Cable (supplied) RF Cable
(Back of TV)
IN
OUT
(Cable box or
Satellite box)
E
Cable
Signal
Connection B
(Back of VCR)
Page 2
- 2 - EN
2. Important Safeguards
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
The caution marking is located on the rear of the cabinet.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
The lightning flash with arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of uninsulated "dangerous
voltage" within the product's enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the product.
1. Read Instructions- All the safety and operating
instructions should be read before the appliance
is operated.
2. Retain Instructions- The safety and operating
instructions should be retained for future reference.
3. Heed Warnings- All warnings on the appliance
and in the operating instructions should be
adhered to.
4. Follow Instructions- All operating and use
instructions should be followed.
5. Cleaning- Unplug this video product from the
wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp cloth
for cleaning.
EXCEPTION: A product that is meant for uninterrupted service and, that for some specific
reason, such as the possibility of the loss of an
authorization code for a CATV converter, is not
intended to be unplugged by the user for cleaning or any other purpose, may exclude the reference to unplugging the appliance in the cleaning description otherwise required in item 5.
6. Attachments- Do not use attachments not rec-
ommended by the video product manufacturer
as they may cause hazards.
7. Water and Moisture- Do not use this video
product near water, for example, near a bath
tub, wash bowl, kitchen sink, or laundry tub, in a
wet basement, or near a swimming pool, and
the like.
8. Accessories- Do not place this video product
on an unstable cart, stand, tripod, bracket, or
table. The video product may fall, causing serious injury to a child or adult, and serious damage to the appliance. Use only with a cart,
stand, tripod, bracket, or table recommended by
the manufacturer, or sold with the video product.
Any mounting of the appliance should follow the
manufacturer's instructions and should use a
mounting accessory recommended by the manufacturer. An appliance and cart combination should
be moved with care. Quick stops,
excessive force, and uneven surfaces may cause the appliance
and cart combination to overturn.
9. Ventilation- Slots and openings in the cabinet
are provided for ventilation and to ensure reliable operation of the video product and to protect it from overheating, and these openings
must not be blocked or covered. The openings
should never be blocked by placing the video
product on a bed, sofa, rug, or other similar surface. This video product should not be placed in
a built-in installation such as a bookcase or rack
unless proper ventilation is provided or the manufacturer's instructions have been adhered to .
10. Power Sources- This video product should be
operated only from the type of power source
indicated on the marking label. If you are not
sure of the type of power supply to your home,
consult your appliance dealer or local power
company. For products intended to operate from
battery power, or other sources, refer to the
operating instructions.
11. Grounding or Polarization- This video product
is equipped with a polarized alternating-current
line plug (a plug having one blade wider than
the other). This plug will fit into the power outlet
only one way. This is a safety feature. If you are
unable to insert the plug fully into the outlet, try
reversing the plug. If the plug should still fail to
fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of
the polarized plug.
12. Power Cord Protection- Power supply cords
should be routed so that they are not likely to be
walked on or pinched by items placed upon or
against them, paying particular attention to
cords at plugs, convenience receptacles, and
the point where they exit from the appliance.
13. Outdoor Antenna Grounding- If an outside
antenna or cable system is connected to the
video product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static
charges. Article 810 of the National Electrical
Code, ANSI/NFPA No. 70, provides information
with regard to proper grounding of the mast and
supporting structure, grounding of the lead-in
wire to an antenna discharge unit, size of
grounding conductors, location of antenna-discharge unit, connection to grounding electrodes,
and requirements for the grounding electrode.
(Fig. A)
14. Lightning- For added protection for this video
product during a lightning storm, or when it is
left unattended and unused for long periods of
time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the video product due to lightning and power-line surges.
15. Power Lines- An outside antenna system
should not be located in the vicinity of overhead
power lines or other electric light or power circuits, or where it can fall into such power lines
or circuits. When installing an outside antenna
system, extreme care should be taken to keep
from touching such power lines or circuits as
contact with them might be fatal.
16. Overloading- Do not overload wall outlets,
extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.
17. Object and Liquid Entry- Never push objects
of any kind into this video product through any
openings as they may touch dangerous voltage
points or short-out parts that could result in a
fire or electric shock. Never spill liquid of any
kind on the video product.
18. Servicing- Do not attempt to service this video
product yourself as opening or removing covers
may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service
personnel.
19. Damage Requiring Service- Unplug this video
product from the wall outlet and refer servicing
to qualified service personnel under the following conditions:
a. When the power-supply cord or plug is dam-
aged.
b. If liquid has been spilled, or objects have fallen
into the video product.
c. If the video product has been exposed to rain or
water.
d. If the video product does not operate normally
by following the operating instructions. Adjust
only those controls that are covered by the
operating instructions as an improper adjustment of other controls may result in damage
and will often require extensive work by a qualified technician to restore the video product to its
normal operation.
e. If the video product has been dropped or dam-
aged in any way.
f. When the video product exhibits a distinct
change in performance-this indicates a need for
service.
20. Replacement Parts- When replacement parts
are required, be sure the service technician has
used replacement parts specified by the manufacturer or have the same characteristics as the
original part. Unauthorized substitutions may
result in fire, electric shock or other hazards.
21. Safety Check- Upon completion of any service
or repairs to this video product, ask the service
technician to perform safety checks to determine
that the video product is in proper operating
condition.
22. Heat- This video product should be situated
away from heat sources such as radiators, heat
registers, stoves, or other products (including
amplifiers) that produce heat.
FIGURE A
EXAMPLE OF ANTENNA GROUNDING
AS PER NATIONAL ELECTRICAL CODE
ANTENNA
LEAD WIRE
GROUND
CLAMP
ELECTRIC
SERVICE
EQUIPMENT
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC – NATIONAL ELECTRICAL CODE
S2898A
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING
CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMP
Page 3
- 3 - EN
3. Preset for Use
2
2
LANGUAGE SELECT
B ENGLISH [ON]
FRANCAIS
ESPAÑOL
Hint
Hint
•
Repeat these steps only if there was a
power failure or if the VCR has been
unplugged for more than 30 seconds.
1
1
Tu rn on the TV and set
it to channel 3.
• If channel 3 is already occupied for broadcasting, see“RF Output Channel” section.
3
3
CH 01
AUTO SET UP
F.FWD
To Select a Channel
You can select a channel by directly
pressing the Number buttons on the
remote control.
Notes for using the Number buttons:
•
When selecting cable channels which
are higher than 99, enter channel
numbers as a three-digit number.(For
example: 117, press 1,1,7)
• You must precede single-digit
channel numbers with a zero (For
example: 02, 03, 04 and so on).
To Preset the Channel Again
1) Press the MENU button until the main
menu appears.
2) Select "CHANNEL SET UP" by pressing the
PLAY or STOP button. Then, press the
F.FWD button.
3)
Select "AUTO SET UP" by pressing
the
PLAY or STOP button. Then, press the
F.FWD button. After scanning, the tuner
stops on the lowest memorized channel.
To Change the On-Screen Language
1) Press the MENU button until the main
menu appears.
2) Select "LANGUAGE SELECT" by pressing
the PLAY or STOP button. Then, press the
F.FWD button.
3)
Select "ENGLISH" , "FRANCAIS" or
"ESPAÑOL"
by pressing the PLAY or STOP
button. Then, press the C.RESET/EXIT button.
1
1
-MENU-
TIMER PROGRAMMING
AUTO REPEAT [OFF]
B CHANNEL SET UP
CLOCK SET
LANGUAGE SELECT
AUDI O OUT
TV STEREO [ON]
SAP
MENU
2
2
CHANNEL SET UP
AUTO SET UP
B MANUAL SET UP
STO
P
PLAY
3
3
MANUAL SET UP
CHANNEL 30 (CATV)
ADD
4
4
MANUAL SET UP
CHANNEL 30 (CATV)
ADD
STO
P
PLAY
F.FWD
F.FWD
STOP
PLAY
F.FWD
1
1
-MENU-
TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
B CLOCK SET
LANGUAGE SELECT
AUDIO OUT
TV STEREO [ON]
SAP
MENU
2
2
CLOCK SET
MONTH DAY YEAR
0 3 / – – – – – –
HOUR MINUTE AM/PM
– – : – – – –
STO
P
PLAY
STOP
PLA
Y
F.FWD
F.FWD
3
3
CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 – – – –
HOUR MINUTE AM/PM
– – : – – – –
STOP
PLAY
F.FWD
4
4
CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 2 0 0 4
HOUR MINUTE AM/PM
– – : – – – –
STOP
PLAY
F.FWD
5
5
CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 MON 2 0 0 4
HOUR MINUTE AM/PM
0 5 : – – – –
STO
P
PLAY
F.FWD
6
6
CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 MON 2 0 0 4
HOUR MINUTE AM/PM
0 5 : 4 0 – –
STO
P
PLAY
F.FWD
7
7
CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 MON 2 0 0 4
HOUR MINUTE AM/PM
0 5 : 4 0 P M AM
B PM
STOP
PLAY
Hint
Hint
• To go back one step, press the REW button
(during the steps [2] to [7].)
• Your clock setting will be lost if there is a
power failure or if the VCR has been
unplugged for more than 30 seconds.
R
E
W
F.FWD
No
No
Please wait for a few minutes.
After scanning...
• The tuner stops on the lowest memorized
channel.
•You can select only the channels memorized
in VCR by using the CHANNEL buttons.
• If "AUTO SET UP" appears on the TV screen
again, check the cable connections.Then,
press the F.FWD button once again.
Hint
Hint
• If you accidentally select Spanish or French
and need English: Press the MENU button
and choose SELEC. IDIOMA, or SELECTION LANGUE. Press the F.FWD button,
and select ENGLISH. Finally, press the
C.RESET/EXIT button.
Select “ADD” or “DELETE”
Select the channel to be
added or deleted.
5
5
To exit the
menu.
C.RESET
EXIT
Select the current month
Select the current day
Select the current year
Select “AM” or “PM”
8
8 To exit the CLOCK SET
screen.
Select the current hour
Select the current minute
YYes
es Press the MENU
button to exit
• Refer to “Hint for Cable Box or
Satellite Box” section on page 1.
Do you connect the cable of the cable box or
the satellite box to the VCR’s ANT IN jack?
Ye s
No
Clock Set UpTo Add/Delete ChannelsTurn on the VCR for the first time
TV ScreenRemote Control
F.FWD
• If the clock is not set, the
CLOCK SET screen
appears when you press
the MENU button. In this
case, go to step [2].
or
or
or
or
or
or
or
or
or
or
or
or
POWER
LAY
P
P
STO
Page 4
- 4 - EN
4. Precautions
Specifications
CAUTION:
TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO
WIDE SLOT, FULLY INSERT.
ATTENTION:
POUR ÉVITER LES CHOC
ÉLECTRIQUES, INTRODUIRE LA
LAME LA PLUS LARGE DE LA
FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET
POUSSER JUSQU’AU FOND.
Moisture Condensation Warning
Moisture condensation may occur inside
the unit when it is moved from a cold
place to a warm place, or after heating a
cold room or under conditions of high
humidity. Do not use the VCR at least for
2 hours until its inside is dry.
FCC Warning
This equipment may generate or use
radio frequency energy. Changes or
modifications to this equipment may
cause harmful interference unless the
modifications are expressly approved in
the instruction manual. The user could
lose the authority to operate this equipment if an unauthorized change or modification is made.
Important Copyright Information
Unauthorized recording or use of broadcast television programming, video tape,
film or other copyrighted material may
violate applicable copyright laws.We
assume no responsibility for the unauthorized duplication, use, or other acts
which infringe upon the rights of copyright owners.
Install Location
For safety and optimum performance of
your VCR:
• Install the VCR in a horizontal and stable position. Do not place anything
directly on top of the VCR. Do not
place the VCR directly on top of the TV.
• Shield it from direct sunlight and keep
it away from sources of intense heat.
Avoid dusty or humid places. Avoid
places with insufficient ventilation for
proper heat dissipation. Do not block
the ventilation holes on the sides of the
VCR. Avoid locations subject to strong
vibration or strong magnetic fields.
Avoid the Hazards of Electrical Shock and
Fire
• Do not handle the power cord with wet
hands.
• Do not pull on the power cord when
disconnecting it from AC wall outlet.
Grasp it by the plug.
A Note about Recycling
This product's packaging materials are
recyclable and can be reused. Please
dispose of any materials in accordance
with your local recycling regulations.
Batteries should never be thrown away
or incinerated but disposed of in accordance with your local regulations concerning chemical wastes.
Note to the Cable TV System Installer
This reminder is provided to call the
Cable TV system installer’s attention to
Article 820-40 of the National Electrical
Code, which provides guidelines for
proper grounding – in particular, specifying that the cable ground shall be connected to the grounding system of the
building, as close to the point of cable
entry as possible.
Precautions
• Designs and specifications are subject to change without notice and legal obligation.
• If an explanation in the Owner’s Manual is not consistent across languages, please
refer to the English version.
CORRECTIVE ACTION
• Make sure the power plug is connected to an AC outlet.
• Make sure the power is turned on.
• Make sure the timer recording is set correctly.
• Make sure the power is off.
• Make sure the VCR clock is set correctly.
• Make sure the tape has a record tab. If needed, cover the hole with
cellophane tape.
• Adjust tracking control for a better picture by pressing the CHANNEL
buttons.
•
Head cleaning may be necessary. Refer to “Auto Head Cleaning” on
page 8.
• Make sure the VCR is not in the Menu mode.
• Turn on the TV and set the TV to channel 3. If channel 3 is already
occupied for broadcasting, change the RF output to channel 4, and
change the TV channel to channel 4. (See “RF Output Channel” on
page 1 for the detail.)
• Fine tune the channel reception on your TV.
• Re-check the ANT. IN and ANT. OUT connections. See page 1.
• Press the VCR/TV button on the remote control so that the VCR/TV
indicator on the VCR disappears.
• Make sure the power plug is connected to an AC outlet.
• Check batteries in remote control.
• You cannot copy a copyrighted video tape.You are experiencing copy
guard protection.
If you are having problems operating your product even though you have followed
the instructions in this manual, check the following list of problems and corrective
actions.You may be able to solve the problem yourself.
PROBLEM
No power.
Timer recording is impossible.
Cannot go into Recording mode.
Playback picture is partially noisy.
No playback picture (only sound
can be heard.)
No or poor playback picture.
TV programs cannot be seen normally.
No VCR operation from the
infrared Remote Control.
Video or color fades in and out when
making a copy of a video tape.
Video Heads : Four Heads
Operating temperature : 41°F~104°F
(5°C~40°C)
Converter output : VHF Channel 3 or 4.
Power requirement : 120V, 60Hz
Power consumption : 14 Watts
Dimensions : W 14-3/16” (360mm)
H 3-5/8” (92mm)
D 8-9/16” (216mm)
Weight : 4.0 lbs. (1.8 Kg.)
(approx.)
Tr oubleshooting Guide
Page 5
2
2
8. On-Screen Operations
1
1 To call up the main menu
6. Recording & OTR (One Touch Recording)
EN
5. Playback
4
4 To exit the menu
- 5 -
-MENU-
B TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
CLOCK SET
LANGUAGE SELECT
2
2 To select an item
-MENU-
TIMER PROGRAMMING
AUTO REPEAT [OFF]
B CHANNEL SET UP
CLOCK SET
LANGUAGE SELECT
3
3 To decide
CHANNEL SET UP
AUTO SET UP
B MANUAL SET UP
PLAYB
POWER
VCR/TVEJECT
CHANNEL
PAUSE
/STILL
C.RESET
EXIT
SEARCH
-MODE
SLOW
DISPLAYSPEED
STOP
PLAY
REC/OTR
MENU
REW
F.FWD
123
456
7809
Before:
Tu r n on the TV and set it to
channel 3.
• If channel 3 is already occupied for broadcasting, see “RF Output Channel” section.
1
1
2
2
3
3
1
1
STOP
EJECT A
3
3
4
4
TAPE INVCR/TVPOWER
4
4
Hint
Hint
•
When a tape without record tab is inserted, the VCR will start playback automatically at step [1].
• Tracking will be automatically adjusted upon playback. To adjust the tracking manually, press the CHANNEL buttons.
TV ScreenRemote Control
PLAY
STOP
EJECT
Accidental erasure prevention
To prevent accidental recording on a recorded cassette, remove its record tab. To record
on it later, cover the hole with cellophane
tape.
Record tab
• Select the
desired channel
1
1
2
2
with tab
SP
• Select the desired tape
speed
3
3
REC
4
4
CH12
TV ScreenRemote Control
CHANNEL
123
456
7809
SPEED
REC/OTR
(
5
5
6
6
STOP
EJECT
To cue or review picture during playback (Picture Search)
Press the F.FWD or REW button.
• Press it again and the VCR will now
search in super high speed. (in the
LP/SLP modes only)
To freeze the picture on TV screen
during playback (Still mode)
Press the PAUSE/STILL button. Each
time you press the button, the picture will
be forwarded by one frame.
• If the picture begins to vibrate vertically
during the still mode, stabilize the picture by pressing the CHANNEL buttons.
• If the picture is distorted or rolling vertically, adjust the vertical hold control on
your TV, if equipped.
Counter Reset
Press the C.RESET/EXIT button.
To play back in slow motion
Press the SLOW button during playback
or the still mode.
• If the noise bar appears on the TV
screen, you can reduce it by pressing
the CHANNEL buttons.
To temporarily stop recording
(Pause mode)
Press the PAUSE/STILL button.
• During the rec pause mode, five
C
marks appear on the TV screen. Each
C
mark represents one minute.
• Press it again to resume recording.
Auto Rewind
When a tape reaches its end during playback, fast-forward, or recording (except
timer recording and One Touch
Recording), the tape will automatically
rewind to the beginning. After rewinding
finishes, the VCR will eject the tape and
turn itself to off.
Before:
Tu rn on the TV and set it to
channel 3.
• If channel 3 is already occupied for
broadcasting, see “RF Output Channel” section.
7. Other Operations
Hint
Hint
• Still/Slow/Pause mode will be automatically cancelled after 5 minutes to prevent damage to the tape and the
video head.
• To return to playback from the Picture Search/Still/Slow mode, press the PLAY button.
STOP
MENU
F.FWD
C.RESET
EXIT
3
3
2
2
MENU
CHANNEL
R
REC/OTR
S
TOP/EJECT
REW
PLAY
F.FWD
TAPE IN TIMER RECVCR/TVPOWER
POWER
VCR/TVEJECT
CHANNEL
PAUSE
/STILL
C.RESET
EXIT
SEARCH
-MODE
SLOW
DISPLAYSPEED
STOP
PLAY
REC/OTR
MENU
REW
F.FWD
123
456
7809
1
1
5
5
6
6
6
6
5
5
4
4
2
2
2
2
3
3
4
4
MENU
REC/OTR
STOP/EJECT
REW
PLAY
F.FW
D
TAPE IN TIMER RECVCR/TVPOWER
POWER
VCR/TVEJECT
CHANNEL
PAUSE
/STILL
C.RESET
EXIT
SEARCH
-MODE
SLOW
DISPLAYSPEED
STOP
PLAY
REC/OTR
MENU
REW
F.FWD
123
456
7809
1
1
2
2
3
3
4
4
1
1
2
2
3
3
4
4
TAPE INVCR/TVPOWER
REC
Hint
Hint
• If you have connected the VCR to a cable box or satellite box, refer to “Hint for
Cable Box or Satellite Box” section on page 1.
STOP
EJECT A
MENU
OR
4
4
or
PLAY
You can select a fixed recording time by pressing the REC/OTR button repeatedly.
4
4
TAPE IN TIMER RECVCR/TVPOWER
Tape Speed Recording/Playback Time
Type of tape T60 T120 T160
SP mode 1hour 2hours 2-2/3hours
SLP mode 3hour 6hour 8hour
REC OTR(0:30) OTR(1:00).....
(Normal recording)
OTR
8:00) OTR(7:30)
PLAY
F
.FW
REW
REC/OTR
MENU
STOP/EJECT
D
Page 6
- 6 EN
9. Recording Features
•Insert a tape with its record tab into the VCR.
F.FWD
8
8
ONE TIME PROGRAM
PROGRAM NUMBER 4
DATE 0 5 / 0 3 MON
START TIME 0 7 : 3 0 PM
END TIME 0 8 : 3 0 PM
CHANNEL 1 6
REC SPEED – –
STOP
PLAY
9
9
ONE TIME PROGRAM
PROGRAM NUMBER 4
DATE 0 5 / 0 3 MON
START TIME 0 7 : 3 0 PM
END TIME 0 8 : 3 0 PM
CHANNEL 1 6
REC SPEED SP B SP
SLP
F.FWD
2
2
PROGRAM NUMBER 4
DATE – – / – –
START TIME – – : – – – –
END TIME – – : – – – –
CHANNEL – –
REC SPEED – –
STOP
PLAY
F.FWD
3
3
PROGRAM NUMBER 4
B ONCE
DAILY
WEEKLY
STOP
PLAY
F.FWD
4
4 Select the desired month
Select the desired day
ONE TIME PROGRAM
PROGRAM NUMBER 4
DATE 0 5 / 0 3 MON
START TIME – – : – – – –
END TIME – – : – – – –
CHANNEL – –
REC SPEED – –
F.FWD
F.FWD
STOP
PLAY
1
1
-MENU-
B TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
CLOCK SET
LANGUAGE SELECT
AUDIO OUT
TV STEREO [ON]
SAP
MENU
Select an empty program
number
Select “ONCE”, “DAILY”
(Mon-Fri), or “WEEKLY”
F.FWD
STOP
5
5 Select the desired start
time (hour)
Select the
minute
ONE TIME PROGRAM
PROGRAM NUMBER 4
DATE 0 5 / 0 3 MON
START TIME 0 7 : 3 0 – –
END TIME – – : – – – –
CHANNEL – –
REC SPEED – –
F.FWD
F.FWD
STOP
6
6
ONE TIME PROGRAM
PROGRAM NUMBER 4
DATE 0 5 / 0 3 MON
START TIME 0 7 : 3 0 PM
END TIME – – : – – – –
CHANNEL – –
REC SPEED – –
AM
B PM
STOP
PLAY
F.FWD
Select “AM” or “PM”
7
7
Repeat the procedure in steps
5 and 6 to set the end time.
Select the desired channel
Select the desired recording speed
10
10
Tu rn off the VCR
for recording
• TIMER indicator on the VCR lights up.
C.RESET
EXIT
POWER
Warning: Unauthorized recordings of copyrighted video tapes
may be an infringement of copyright laws.
ANT
IN
OUT
AUDIO
VIDEO
OUT IN
OUT
L
R
IN
ANT
IN
OUT
AUDIO
VIDEO
OUT IN
OUT
L
R
IN
ANT
IN
OUT
AUDIO
VIDEO
OUT IN
OUT
L
R
IN
VIDEO
ANT
IN
OUT
AUDIO
OUT IN
OUT
L
R
IN
Connect
1
2
Connect
1) Insert a pre-recorded tape into the playing VCR.
2) Insert a tape with its record tab into the recording VCR.
3) Press
the SPEED button on the remote control of the recording VCR
to select the desired recording speed (SP/SLP).
4) Select the “L1” or “L2”position on the recording VCR.
• To use the input jacks on the back of the VCR, select "L1" position by
pressing
[0], [0], [1] on the remote control or the CHANNEL buttons.
• To use the input jacks on the front of the VCR, select "L2" position by
pressing
[0], [0], [2] on the remote control or the CHANNEL buttons.
5) Press
the REC/OTR button on the recording VCR.
6) Begin playback of the tape in the playing VCR.
7) To stop recording, press the
STOP/EJECT button on the recording
VCR, then stop playback of the tape in the playing VCR.
1) Turn the power on by pressing
the POWER button.
2) Select main menu by pressing
the MENU button.
3) Select "TIMER PROGRAMMING" by pressing the PLAY or
STOP button.Then, press the
F.FWD button.
4) Select the program number
which you want to check by
pressing the PLAY or STOP button. The details of the program
you selected will appear on the
TV screen.
• Go to the digit you want to
change by pressing the F.FWD
or REW button. Then, enter correct numbers by pressing the
PLAY or STOP button.
• You may cancel the entire program by pressing the REW button while the program number
flashes.
5) Press the C.RESET/EXIT button
to exit.
6) Press the POWER button to
return to timer stand-by mode.
To Check, Correct, or Cancel a
Timer Program
Hint
Hint
• To go back one step, press the REW button
(during the steps [3] to [9].)
• If there is a power failure or the VCR has been unplugged for more than 30 seconds, the clock setting and all timer settings will be lost.
• If the tape runs out before the end time, the VCR will switch to the Stop mode
immediately, eject the tape and the VCR power will be turned off.The TIMER
indicator will flash.
• If a tape is not in the VCR or does not have the record tab, the TIMER indicator
flashes and timer recording cannot be performed. Please insert a recordable tape.
• When all the Timer Recording are completed, the TIMER indicator flashes.
To play or eject the recorded tape, press the POWER button first, and then
press the PLAY or EJECT button.
Press the STOP/EJECT button on the VCR.
To cancel a Timer Recording that is in progress
Hint
Hint
• For best results during dubbing, use the VCR’s front panel controls whenever possible. The
remote control might affect the playing VCR’s operation.
• Always use video-quality shielded cables with RCA-type connectors. Standard audio cables are
not recommended.
• You can use a video disc player, satellite receiver, or other audio/video component with A/V outputs in place of the playing VCR.
• “L1” or “L2” is found before the lowest memorized channel. (Example: CH02)
Timer Recording Hint for Timer Recording
Copying a Video Tape
•
If you have connected the VCR to a cable
box or satellite box as the Connection A
on page 1, select the VCR to channel 3 or
4 (the RF output channel of the VCR).
Then, select the desired channel at the
cable box or satellite box. Leave the cable
box or satellite box on for timer recording.
or
or
or
PLAY
• You can program one
year in advance.
or
PLAY
or
or
or
STOP
or
PLAY
STOP
or
PLAY
(Back of Playing VCR)
(Back of Recording VCR*)
Audio/Video Cables
(not supplied)
RF Cable
(supplied)
(Back of TV)
*Front input jacks are also available
Page 7
- 7 - EN
10. Special Features
You can specify the time for
fast forwarding or rewinding.
• Insert a tape into the VCR.
You can specify the number of
programs to be skipped.
• Insert a tape into the VCR.
1
1
TIME SEARCH
– : – –
SEARCH
-MODE
2
2 Select the desired length
of time for fast forwarding
or rewinding
TIME SEARCH
2 : 5 0
STOP
PLAY
Hint f
Hint f
or
or
Timer Sear
Timer Searcc
h & Inde
h & Inde
x Sear
x Searcchh
• These functions are not available during recording.
• Press the STOP button to stop the search.
• If the end of the tape is reached during a Search, the VCR will cancel the search and rewind the
tape.
1
1
INDEX SEARCH
– –
2
2
INDEX SEARCH
0 3
STOP
PLAY
3
3
1
1
-MENU-
TIMER PROGRAMMING
B AUTO REPEAT [OFF]
CHANNEL SET UP
CLOCK SET
LANGUAGE SELECT
AUDI O OUT
TV STEREO [ON]
SAP
MENU
STOP
PLAY
2
2
-MENU-
TIMER PROGRAMMING
B AUTO REPEAT [ON]
CHANNEL SET UP
CLOCK SET
LANGUAGE SELECT
AUDIO OUT
TV STEREO [ON]
SAP
F.FWD
Hint
Hint
• To cancel Auto Repeat, follow steps [1]-[2]
above. Then, press the F.FWD button so
that [OFF] appears beside AUTO REPEAT.
Press the C.RESET/EXIT button to exit.
• If menu remains on the TV screen at step
[3], press the C.RESET/EXIT button to exit.
You can repeat playback of a
whole tape automatically.
• Insert a tape into the VCR.
Pro.1 Pro.2 Pro.3 Pro.4 Pro.5
02 01 01 02 03
Beginning
of tape
End
of tape
CURRENT PROGRAM
INDEX MARK
F.FWD
1
1
-MENU-
TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
CLOCK SET
LANGUAGE SELECT
AUDIO OUT
B TV STEREO [ON]
SAP
MENU
STOP
PLAY
1
1
-MENU-
TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
CLOCK SET
LANGUAGE SELECT
B AUD IO OUT
TV STEREO [ON]
SAP
MENU
STOP
PLAY
11. MTS System
(Multi-Channel Television Sound)
Select “TV STEREO” or
“SAP”
2
2 To exit the menu.
C.RESET
EXIT
2
2
AUDIO OUT
B HIFI [ON]
MONO
F.FWD
Select “HIFI” or “MONO”
STOP
PLAY
Time Search Index Search Auto Repeat
When You Receive or Record a
Program Broadcast in MTS
When You Play Back a Tape
Recorded in Hi-Fi Stereo
x2 (Twice)
SEARCH
-MODE
x1 (Once)
0:01~ 9:59
(1 minute~9 hours
and 59 minutes)
01 ~ 20
F.FWD
REW
To rewind To fast forward
4
4
After searching,
PLAYB
3
3
F.FWD
REW
To rewind To fast forward
4
4
After searching,
3
3
AUTO REPEAT B
PLAYB
Hint
Hint
• The VCR records an index mark at the
beginning of the recording when you make
a recording. There should be time gap
between index marks for the Index Search.
or
or
or
• When you receive a broadcast on the VCR, you can
check the type of the broadcast by pressing the DISPLAY
button.
• When "TV STEREO" or
"SAP" selection is valid,
select them by following
steps. This selection is needed when you record the program.
• SAP means Second Audio
Program (usually second language).
or
• If you have connected a
stereo TV to this VCR, select
"STEREO".
• If you have connected a
monaural TV to this VCR,
select "MONO".
3
3 To exit the menu.
C.RESET
EXIT
or
or
-None-
SAP
SAP
Type of
broadcast
Regular
(monaural audio)
Stereo
broadcast
Bilingual
broadcast
Stereo &
Bilingual
broadcast
STEREO/SAP
Selection
-Invalid-
-Invalid-
TV STEREO
(main audio program)
SAP
(second audio program)
TV STEREO
(stereo main audio program)
SAP
(second audio program)
Display on the
TV screen
STEREO
STEREO
Your Selection
Type of recorded tape
non Hi-Fi tapes
Hi-Fi tapes
recorded in
Hi-Fi stereo
Hi-Fi tapes
recorded main
audio program
Hi-Fi tapes
recorded second
audio program
Monaural
L
Main audio
program
Second audio
program
STEREO
R-channelL-channel
Monaural
Main audio
program
Second audio
program
R
MONO
Monaural
Main audio
program
Second audio
program
L+R
Page 8
12. Information
- 8 - EN
Servicing
Should your VCR become inoperative, do not
try to correct the problem by yourself. There
are no user-serviceable parts inside. Turn off,
unplug the power plug, and please call our
help line mentioned on page 1 to locate an
Authorized Service Center.
Cabinet Cleaning
• Wipe the front panel and other exterior surfaces of the VCR with a soft cloth immersed
in lukewarm water and wrung dry.
• Never use a solvent or alcohol. Do not spray
insecticide liquid near the VCR. Such chemicals may cause damage and discoloration to
the exposed surfaces.
Auto Head Cleaning
• Automatically cleans video heads as you insert or
remove a cassette, so you can see a clear picture.
• Playback picture may become blurred or interrupted while the TV program reception is clear. Dirt
accumulated on the video heads after long periods of use, or the usage of rental or worn tapes
can cause this problem. If a streaky or snowy picture appears during playback, the video heads in
your VCR may need to be cleaned.
1. Please visit your local Audio/Video store and pur-
chase a good quality VHS Video Head Cleaner.
2. If a Video Head Cleaner does not solve the
problem, please call our help line mentioned on
page 1 to locate an Authorized Service Center.
NOTES:
• Remember to read the instructions included with
the video head cleaner before use.
• Clean video heads only when problems occur.
PREPARACIÓN DE CANALES
(La antena o la caja de televisión por
cable deberá estar conectada)
NOTES: Cuando utilice su nueva
videograbadora por primera vez, o en el
caso de ser necesario después de producirse un fallo en la alimentación, la
videograbadora se pondrá inicialmente en el
modo de preajuste cuando se pulse
[POWER].
1. Encienda el televisor y ponga el televisor
en el canal 3.
2. Pulse [POWER] para encender la
videograbadora.
3. Seleccione "ENGLISH",
"FRANCAIS"(French)
o "ESPAÑOL"
(Spanish) pulsando
[PLAY] o [STOP].Y
luego pulse [F.FWD].
4. Pulse una vez
[F.FWD].
El sintonizador explora
y memoriza todos los canales activos de su
zona. Tras la exploración, el sintonizador se
detiene en el canal memorizado más bajo.
PREPARACIÓN DEL RELOJ
1. Pulse [MENU] hasta que aparezca el
menú principal. (Si el reloj no está puesto
en hora y se pulsa [MENU], el menú
AJUSTE DE RELOJ aparece en primer
lugar. En este caso, siga el paso 3.)
2. Pulse [PLAY] o [STOP] para indicar a
"AJUSTE DE RELOJ". Luego, pulse [F.FWD].
3.
• Para volver atrás un
paso, pulse [REW].
4. Pulse [F.FWD] para
poner en funcionamiento el reloj.
Ajuste el mes.
Ajuste el día.
Ajuste el año.
Ajuste el minuto.
Ajuste la
mañana (AM) o
la tarde (PM).
Ajuste la hora.
Pulse repetidamente [PLAY] o [STOP].
Luego, pulse [F.FWD].
Pulse repetidamente [PLAY] o [STOP].
Luego, pulse [F.FWD].
Pulse repetidamente [PLAY] o [STOP].
Luego, pulse [F.FWD].
Pulse repetidamente [PLAY] o [STOP].
Luego, pulse [F.FWD].
Pulse repetidamente [PLAY] o [STOP].
Luego, pulse [F.FWD].
Pulse repetidamente [PLAY] o [STOP].
SELEC. IDIOMA
ENGLISH
FRANCAIS
B ESPAÑOL [ON]
AJUSTE DE RELOJ
MES DIA AÑO
03 / 15 LUN 2004
HORA MINUTO AM/PM
05 : 40 PM AM
BPM
Maintenance
Instrucciones en Español
Funai Corporation will exchange or repair this product, at its option, in the event of defect in materials
or workmanship as follows:
EXCHANGE DURATION:
1-90 DAYS:
FUNAI CORPORATION will
exchange for a new unit without
charge for a period of ninety (90)
days from the date of original retail
purchase.
91-365 DAYS: FUNAI CORPORATION will exchange
for a factory-service-to-new-condition
unit for a charge of a retailed price unit
for the period of ninety one (91) days to
three hundred sixty five (365) days from
the date of original retail purchase.
REPAIR DURATION:
LABOR:
FUNAI CORPORATION will provide
the labor without charge for a period
of ninety (90) days from the date of
original retail purchase.
PA RTS: FUNAI CORPORATION will provide
parts to replace defective parts
without charge for a period of one
(1) year from the date of original
retail purchase. Certain parts are
excluded from this warranty.
LIMITS AND EXCLUSIONS:
THIS WARRANTY IS EXTENDED ONLY TO THE ORIGINAL RETAIL PURCHASER. A PURCHASE RECEIPT OR
OTHER PROOF OF ORIGINAL RETAIL PURCHASE
WILL BE REQUIRED TOGETHER WITH THE PRODUCT
TO OBTAIN EXCHANGE OR SERVICE UNDER THIS
WARRANTY.
This warranty shall not be extended to any other person or transferee.
This warranty is void and of no effect if any serial
numbers on the product are altered, replaced,
defaced or missing. This EMERSON Limited warranty applies only to product purchased and used in the
United States.
This warranty only covers failures due to defects in
material or workmanship, which occur during normal
use. It does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations, or parts not supplied by FUNAI CORPORATION, or damage which results from accident, misuse, abuse, mishandling, misapplication, alteration,
faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this
product, or damage which results from fire, flood,
lightning or other acts of God.
THIS WARRANTY DOES NOT COVER PACKING
MATERIALS, ANY ACCESSORIES (EXCEPT
REMOTE CONTROL UNITS), ANY COSMETIC
PA RTS, COMPLETE ASSEMBLY PARTS, DEMONSTRATION OR FLOOR MODELS.
FUNAI CORPORATION AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE
LIABLE FOR ANY GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR
OCCASIONED BY THE USE OF OR THE INABILITY
TO USE THIS PRODUCT. THIS WARRANTY IS
MADE IN LIEU OF ALL OTHER WARRANTIES
INCLUDING THE WARRANTY OF MERCHANT
ABILITY, AND FITNESS FOR A PARTICULAR PURPOSE, THAT ARE HEREBY DISCLAIMED BY
FUNAI CORPORATION AND ITS REPRESENTATIVES OR AGENTS IN THE UNITED STATES.
ALL WARRANTY INSPECTIONS AND REPAIRS
MUST BE PERFORMED BY A FUNAI AUTHORIZED CENTER. THIS WARRANTY IS VALID
WHEN THE PRODUCT IS DELIVERED PREPAID
TO A FUNAI AUTHORIZED SERVICE FACILITY.
IMPORTANT:
THIS LIMITED WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS
THAT VARY FROM STATE TO STATE, IF AT ANY
TIME DURING THE WARRANTY PERIOD YOU
ARE UNABLE TO OBTAIN SATISFACTION WITH
THE EXCHANGE OR REPAIR OF THIS PRODUCT,
PLEASE CONTACT FUNAI CORPORATION.
ATTENTION:
FUNAI CORPORATION RESERVES THE
RIGHT TO MODIFY ANY DESIGN OF
THIS PRODUCT WITHOUT PRIOR
NOTICE.
For information about your product, or for
information on how to exchange or repair
your product, telephone or write to the following:
FUNAI CORPORATION, INC.
SERVICE CENTER
19900 Van Ness Avenue, Torrance, CA 90501
Telephone (800)256-2487
http://www.funai-corp.com
Head Office: 100 North Street, Teterboro, NJ 07608
PLEASE DO NOT SHIP YOUR UNIT TO THE
TETERBORO ADDRESS.
LIMITED WARRANTY
Page 9
documentation manual, user maintenance, brochure, user reference, pdf manual
This file has been downloaded from:
User Manual and User Guide for many equipments like mobile phones, photo cameras, monther board, monitors, software, tv, dvd, and othes..
Manual users, user manuals, user guide manual, owners manual, instruction manual, manual owner, manual owner's, manual guide,
manual operation, operating manual, user's manual, operating instructions, manual operators, manual operator, manual product,
Loading...