Funai EWR20V4 User Manual
• Remote control
(NB108UD)
with two AA batteries
• RF cable
(
WPZ
0901TM002)
• Audio/Video cables
(WPZ0102TM015 or
WPZ0102LTE01)
• Owner’s Manual
(0VMN04201)
• Quick Use Guide
(1VMN20003)
Owner's Manual
Before you start
If you need additional operating assistance after reading this owner’s manual or to
order replacement accessories, please call
TOLL FREE : 1-800-605-8457
or visit our web site at http://www.funai-corp.com
Before you use this unit , you need to complete connections. Refer to
“Connections” on pages 13-15.
To r ecord a program easily, refer to “Easy DVD recording” on pages 16-17
after connections are completed.
(You CANNOT record on any copyright protected DVD disc with this unit.)
EWR20V4
INSTRUCCIONES EN ESPAÑOL INCLUIDAS.
Owner’s Manual
DVD Recorder with Video Cassette Recorder
Supplied Accessory
Español
Recording Playing discs EditingConnections Getting started
Changing the SETUP menu
VCR functions Others
EMERSON AND THE G-CLEF LOGO ARE REGISTERED TRADEMARKS
OF EMERSON RADIO CORP., PARSIPPANY, NEW JERSEY, U.S.A
.
SELECT STOP PLAY RECORD
L - AUDIO - R
VCR DVD
CHANNEL DUBBING
OPEN/CLOSE
POWER
REW F.FWD PLAY RECORD
STOP/EJECT
SELECT
S-VIDEO VIDEO
Precautions
Before you start
Laser Safety
2
This unit employs a laser. Only a qualified service person should remove the cover or attempt to service this device, due to possible eye injury.
CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN
MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
CAUTION: VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED. DO NOT STARE INTO BEAM.
LOCATION: INSIDE, NEAR THE DECK MECHANISM.
WARNING
: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLI-
ANCE TO RAIN OR MOISTURE.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of
uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk
of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating
and maintenance (servicing) instructions in the literature
accompanying the appliance.
CAUTION
:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER
(OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
RADIO-TV INTERFERENCE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses,and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
1) Reorient or relocate the receiving antenna.
2) Increase the separation between the equipment and receiver.
3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4) Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
FCC WARNING- This equipment may generate or use radio frequency energy. Changes or modifications to
this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual.The user could lose the authority to operate this equipment if an unauthorized change or modification is made.
CAUTION:TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES,INTRODUIRE LA LAME LA PLUS LARGE DE LA
FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU
FOND.
A NOTE ABOUT RECYCLING
This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with your local recycling regulations.
Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concerning chemical
wastes.
For Customer Use:
Read carefully the information located at the back of this unit and enter below the Serial No.Retain this information for future reference.
Model No.
_____________________
Serial No. _____________________
Make your contribution to the environment!!!
• Used up batteries do not belong in the dust bin.
• You can dispose of them at a collection point for used up batteries or special waste.
Contact your council for details.
Before you start
Español
Recording
Playing discs EditingConnections Getting started
Changing the SETUP menu
VCR functions Others
Before you start
3
Important Safeguards
1. Read Instructions - All the safety and operating instructions
should be read before the appliance is operated.
2. Retain Instructions- The safety and operating instructions should
be retained for future reference.
3. Heed Warnings - All warnings on the appliance and in the operating instructions should be adhered to.
4. Follow Instructions - All operating and use instructions should
be followed.
5. Cleaning - Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners. Use a
damp cloth for cleaning.
EXCEPTION:A product that is meant for uninterrupted service and, that for some specific reason, such as the possibility
of the loss of an authorization code for a CATV converter,is
not intended to be unplugged by the user for cleaning or any
other purpose, may exclude the reference to unplugging the
appliance in the cleaning description otherwise required in
item 5.
6.Attachments - Do not use attachments not recommended by
the product manufacturer as they may cause hazards.
7.Water and Moisture- Do not use this product near water, for
example, near a bath tub, wash bowl, kitchen sink, or laundry
tub, in a wet basement, or near a swimming pool,and the like.
8.Accessories - Do not place this product on an unstable cart,
stand, tripod, bracket, or table.The product may fall,causing serious injury to a child or adult, and serious damage to the appliance. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold
with the product. Any mounting of the
appliance should follow the manufacturer's
instructions and should use a mounting
accessory recommended by the manufacturer. An appliance and cart combination
should be moved with care. Quick stops,
excessive force, and uneven surfaces may
cause the appliance and cart combination to overturn.
9.Ventilation - Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the product and
to protect it from overheating,and these openings must not be
blocked or covered.The openings should never be blocked by
placing the product on a bed, sofa, rug,or other similar surface.
This product should not be placed in a built-in installation such
as a bookcase or rack unless proper ventilation is provided or
the manufacturer's instructions have been adhered to.
10. Power Sources - This product should be operated only from the
type of power source indicated on the marking label. If you are
not sure of the type of power supply to your home,consult your
appliance dealer or local power company. For products intended to operate from battery power, or other sources, refer to the
operating instructions.
11. Grounding or Polarization - This product is equipped with a
polarized alternating-current line plug (a plug having one blade
wider than the other). This plug will fit into the power outlet
only one way.This is a safety feature. If you are unable to insert
the plug fully into the outlet, try reversing the plug. If the plug
should still fail to fit, contact your electrician to replace your
obsolete outlet. Do not defeat the safety purpose of the polarized plug.
12. Power Cord Protection - Power supply cords should be routed
so that they are not likely to be walked on or pinched by items
placed upon or against them,paying particular attention to cords
at plugs, convenience receptacles, and the point where they exit
from the appliance.
13. Outdoor Antenna Grounding - If an outside antenna or cable
system is connected to the product, be sure the antenna or
cable system is grounded so as to provide some protection
against voltage surges and built-up static charges.Article 810 of
the National Electrical Code,ANSI/NFPA No.70, provides information with regard to proper grounding of the mast and sup-
porting structure, grounding of the lead-in wire to an antenna
discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and
requirements for the grounding electrode. (Fig.A)
14. Lightning - For added protection for this product during a lightning storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and disconnect
the antenna or cable system. This will prevent damage to the
product due to lightning and power-line surges.
15. Power Lines - An outside antenna system should not be located
in the vicinity of overhead power lines or other electric light or
power circuits,or where it can fall into such power lines or circuits.When installing an outside antenna system, extreme care
should be taken to keep from touching such power lines or circuits as contact with them might be fatal.
16. Overloading - Do not overload wall outlets and extension cords
as this can result in a risk of fire or electric shock.
17. Object and Liquid Entry - Never push objects of any kind into
this product through any openings as they may touch dangerous
voltage points or short-out parts that could result in a fire or
electric shock. Never spill liquid of any kind on the product.
18. Servicing - Do not attempt to service this product yourself as
opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
19. Damage Requiring Service - Unplug this product from the wall
outlet and refer servicing to qualified service personnel under
the following conditions:
a.When the power-supply cord or plug is damaged.
b. If liquid has been spilled,or objects have fallen into the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following the oper-
ating instructions.Adjust only those controls that are covered by
the operating instructions as an improper adjustment of other
controls may result in damage and will often require extensive
work by a qualified technician to restore the product to its nor-
mal operation.
e. If the product has been dropped or damaged in any way.
f.When the product exhibits a distinct change in performance this
indicates a need for service.
20. Replacement Parts - When replacement parts are required, be
sure the service technician has used replacement parts specified
by the manufacturer or have the same characteristics as the
original part. Unauthorized substitutions may result in fire, electric shock or other hazards.
21. Safety Check - Upon completion of any service or repairs to this
product, ask the service technician to perform safety checks to
determine that the product is in proper operating condition.
22. Heat - This product should be situated away from heat sources
such as radiators, heat registers, stoves, or other products
(including amplifiers) that produce heat.
Precautions (cont’d)
FIGURE A
EXAMPLE OF ANTENNA GROUNDING
AS PER NATIONAL ELECTRICAL CODE
GROUND
CLAMP
ELECTRIC
SERVICE
EQUIPMENT
NEC – NATIONAL ELECTRICAL CODE
S2898A
ANTENNA
LEAD
WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMP
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
4
Precautions (cont’d)
Before you start
Installation Location
For safety and optimum performance of this unit:
• Install the unit in a horizontal and stable position. Do not
place anything directly on top of the unit. Do not place
the unit directly on top of the TV.
• Shield it from direct sunlight and keep it away from
sources of intense heat.Avoid dusty or humid places.
Avoid places with insufficient ventilation for proper heat
dissipation. Do not block the ventilation holes on the
sides of the unit.Avoid locations subject to strong vibration or strong magnetic fields.
Avoid the Hazards of Electrical Shock and Fire
• Do not handle the power cord with wet hands.
• Do not pull on the power cord when disconnecting it
from AC wall outlet. Grasp it by the plug.
• If, by accident, water is spilled on this unit, unplug the
power cord immediately and take the unit to our
Authorized Service Center for servicing.
• Do not put your fingers or objects into the unit cassette
holder.
Moisture Condensation Warning
Moisture condensation may occur inside the unit when it is
moved from a cold place to a warm place, or after heating
a cold room or under conditions of high humidity. Do not
use this unit at least for 2 hours until its inside gets dry.
About Copyright
Unauthorized copying, broadcasting, public performance
and lending of discs are prohibited.
This product incorporates copyright protection technology that is protected by method claims of certain U.S.
patents and other intellectual property rights owned by
Macrovision Corporation and other rights owners. Use of
this copyright protection technology must be authorized
by Macrovision Corporation, and is intended for home and
other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or
disassembly is prohibited.
Symbol in this owner's manual
Many functions of this unit are depending on the disc type
or the recording mode.
To specify for what disc type or recording mode each
function is, we put the following symbols at the beginning
of each item to operate.
Maintenance
SERVICING
• Please refer to relevant topics on the Troubleshooting
Guide on pages 97-99 before return the product.
• When this unit becomes inoperative, do not try to correct the problem by yourself.There are no user-serviceable parts inside.Turn off, unplug the power plug, and
please call our help line mentioned on the front page to
locate an Authorized Service Center.
CLEANING THE CABINET
• Use a soft cloth slightly moistened with a mild detergent
solution. Do not use a solution containing alcohol, spirits,
ammonia or abrasive.
CLEANING DISCS
• When a disc becomes dirty, clean it with a cleaning
cloth.Wipe the disc from the center out. Do not wipe in
a circular motion.
• Do not use solvents such as benzine, thinner, commercially available cleaners, detergent, abrasive cleaning
agents or antistatic spray intended for analogue records.
CLEANING THE DISC LENS
• If this unit still does not perform properly although you
refer to the relevant sections and to “TROUBLESHOOTING GUIDE” in this Owner’s Manual, the laser optical pickup unit may be dirty. Consult your dealer or an Authorized
Service Center for inspection and cleaning of the laser optical pickup unit.
DISC HANDLING
• Handle the discs so that fingerprints and dust do not
adhere to the surfaces of the discs.
• Always store the disc in its protective case when it is
not used.
AUTO HEAD CLEANING
• Automatically cleans video heads as you insert or
remove a cassette, so you can see a clear picture.
• Playback picture may become blurred or interrupted
while the TV program reception is clear. Dirt accumulated on the video heads after a long period of use, or the
usage of rental or worn tapes can cause this problem. If
a streaky or snowy picture appears during playback, the
video heads in the unit may need to be cleaned.
1. Please visit your local Audio/Video store and purchase a
good quality VHS Video Head Cleaner.
2. If a Video Head Cleaner does not solve the problem,
please call our help line mentioned on the front page to
locate an Authorized Service Center.
NOTES:
• Remember to read the instructions along with the video
head cleaner before use.
• Clean video heads only when problems occur.
Symbol
First:
(Press:)
First:
(Press:)
DVD-V
DVD-V
Video
DVD-RW
DVD-RW
DVD-RW
DVD-RW
DVD-R
DVD-R
CD
CD
MP3
MP3
VCR
VCR
VR
Description
Available to DVD Video discs
Available to DVD-RW in Video mode
Available to DVD-RW in VR mode
Available to DVD-R discs
Available to Audio CDs
Available to CD-R/RW discs with
MP3 files
Available to VHS tapes
Use only cassettes marked
with this unit.
Indicates that you need to select the DVD
DVD
mode by pressing DVD button on the
remote control before proceeding next step.
Indicates that you need to select the VCR
VCR
mode by pressing VCR button on the
remote control before proceeding next step.
Recording
Playing discs Editing
Before you start
Connections Getting started
Changing the SETUP menu
VCR functions Others
Español
5
Ta b le of contents
Before you start
Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Title/Chapter search . . . . . . . . . . . . . . . . . . . . . . . .52
Track search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Time search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Repeat/Random/Program play . . . . . . . . . . . . . .54
Repeat play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Random play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Program play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Selecting the format of audio and video . . . . . .56
Switching audio soundtrack . . . . . . . . . . . . . . . . . . .56
Switching subtitles . . . . . . . . . . . . . . . . . . . . . . . . . .57
Switching camera angles . . . . . . . . . . . . . . . . . . . . . .58
Reducing block noise . . . . . . . . . . . . . . . . . . . . . . . .58
Editing . . . . . . . . . . . . . . . . . . . . . . . . .59
Information on disc editing . . . . . . . . . . . . . . . . .59
Guide to a title list . . . . . . . . . . . . . . . . . . . . . . . . . .59
Editing discs in Video mode . . . . . . . . . . . . . . . . . . .59
Editing discs in VR mode . . . . . . . . . . . . . . . . . . . . .60
Editing DVD-RW discs in Video mode . . . . . . . .61
Deleting titles . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
Putting names on titles . . . . . . . . . . . . . . . . . . . . . .62
Setting or clearing chapter markers . . . . . . . . . . . . .64
Editing DVD-RW discs in VR mode (Original) . .65
Deleting titles . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Deleting parts of titles . . . . . . . . . . . . . . . . . . . . . . .66
Putting names on titles . . . . . . . . . . . . . . . . . . . . . .67
Setting or clearing chapter markers . . . . . . . . . . . . .69
Setting pictures for thumbnails . . . . . . . . . . . . . . . . .70
Setting titles to protect . . . . . . . . . . . . . . . . . . . . . .72
Releasing titles from protecting . . . . . . . . . . . . . . . .73
Editing DVD-RW discs in VR mode (Playlist) . . .74
Deleting titles . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
Deleting parts of titles . . . . . . . . . . . . . . . . . . . . . . .75
Putting names on titles . . . . . . . . . . . . . . . . . . . . . .76
Setting or clearing chapter markers . . . . . . . . . . . . .78
Setting pictures for thumbnails . . . . . . . . . . . . . . . . .79
Adding titles to a Playlist . . . . . . . . . . . . . . . . . . . . .81
Deleting a Playlist . . . . . . . . . . . . . . . . . . . . . . . . . . .82
Editing DVD-R discs . . . . . . . . . . . . . . . . . . . . . .83
Deleting titles . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83
Putting names on titles . . . . . . . . . . . . . . . . . . . . . .84
Changing the SETUP menu . . . . . . . . .85
Tour of the SETUP menu . . . . . . . . . . . . . . . . . .85
Settings for Language . . . . . . . . . . . . . . . . . . . . .86
Settings for Display . . . . . . . . . . . . . . . . . . . . . . .88
Settings for Audio . . . . . . . . . . . . . . . . . . . . . . . .90
Settings for Parental lock level . . . . . . . . . . . . . .92
VCR functions . . . . . . . . . . . . . . . . . . .94
Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94
Recording and One-touch timer recording . . . .94
Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94
One-touch timer recording . . . . . . . . . . . . . . . . . . . .95
Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95
Index Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95
Time Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96
Other operations . . . . . . . . . . . . . . . . . . . . . . . .96
Others . . . . . . . . . . . . . . . . . . . . . . . . .97
Tr oubleshooting . . . . . . . . . . . . . . . . . . . . . . . . .97
RF converter output . . . . . . . . . . . . . . . . . . . . .100
Language code . . . . . . . . . . . . . . . . . . . . . . . . .101
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . .103
Español . . . . . . . . . . . . . . . . . . . . . . . .104
Before you start . . . . . . . . . . . . . . . . . . .2
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Ta b le of contents . . . . . . . . . . . . . . . . . . . . . . . . . .5
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Functional overview . . . . . . . . . . . . . . . . . . . . . . .7
Installing batteries in the remote control . . . . . . . . . .9
Using a remote control . . . . . . . . . . . . . . . . . . . . . . .9
VCR/DVD recorder switching . . . . . . . . . . . . . . . . . . .9
SETUP/DISC/CD menu . . . . . . . . . . . . . . . . . . . . . . . .9
DISPLAY menu . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Connections . . . . . . . . . . . . . . . . . . . . .13
Connection to a TV . . . . . . . . . . . . . . . . . . . . . . .13
Connection to a cable box or satellite box . . . .14
Connection to an Audio System . . . . . . . . . . . . .15
Getting started . . . . . . . . . . . . . . . . . . .16
Easy DVD recording . . . . . . . . . . . . . . . . . . . . . .16
Channel setting . . . . . . . . . . . . . . . . . . . . . . . . . .18
Getting channels automatically . . . . . . . . . . . . . . . . .18
Adding/deleting channels . . . . . . . . . . . . . . . . . . . . .19
Selecting the TV stereo or SAP . . . . . . . . . . . . .20
Clock setting . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Auto Clock Setting . . . . . . . . . . . . . . . . . . . . . . . . .21
Manual Clock Setting . . . . . . . . . . . . . . . . . . . . . . . .22
Setting the daylight saving time . . . . . . . . . . . . . . . .24
Selecting the TV aspect ratio . . . . . . . . . . . . . . .25
Recording . . . . . . . . . . . . . . . . . . . . . . .26
Information on DVD recording . . . . . . . . . . . . . .26
Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Recording speed . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Restrictions on recording . . . . . . . . . . . . . . . . . . . .26
Information on copy control . . . . . . . . . . . . . . . . . .27
Making discs playable in other DVD player (Finalize) 27
Formatting a disc . . . . . . . . . . . . . . . . . . . . . . . .28
Settings for the recording format to a blank disc . . .28
Reformatting a disc . . . . . . . . . . . . . . . . . . . . . . . . .30
Basic recording . . . . . . . . . . . . . . . . . . . . . . . . . .31
Checking the recording picture quality . . . . . . . . . .32
One-touch timer recording . . . . . . . . . . . . . . . .33
Timer recording . . . . . . . . . . . . . . . . . . . . . . . . .34
Hints for timer recording . . . . . . . . . . . . . . . . . . . . .36
Settings for an external source . . . . . . . . . . . . . .37
Connection to an external source . . . . . . . . . . . . . .37
Recording from an external source . . . . . . . . . . . . .38
Dubbing Mode . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Finalizing the discs . . . . . . . . . . . . . . . . . . . . . . .41
Setting a disc to protect . . . . . . . . . . . . . . . . . . .42
Playing discs . . . . . . . . . . . . . . . . . . . . .43
Information on DVD play . . . . . . . . . . . . . . . . . .43
Guide to displays . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Basic playback . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Playing discs using the disc menu . . . . . . . . . . . . . . .46
Playing discs using the title menu . . . . . . . . . . . . . . .47
Special playback . . . . . . . . . . . . . . . . . . . . . . . . .48
Resume play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Fast forward / Fast reverse . . . . . . . . . . . . . . . . . . .48
Skipping TV commercials during playback . . . . . . . . .49
Pause . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Step by step playback . . . . . . . . . . . . . . . . . . . . . . . .50
Slow forward / Slow reverse play . . . . . . . . . . . . . . .50
Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Marker Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Features
Before you start
6
Recording
This unit is compatible with both DVD-RW, which is
rewritable repeatedly, and DVD-R, which is available for
recording once.Also, this unit allows to record to the
video cassette tape. You can choose either one for your
convenience.
Up to 8 programs recording:
You can program the unit to record up to 8 programs, up
to a year in advance. Daily or weekly program recordings
are also available.
One-touch timer recording:
Easily you can set a recording time as you prefer. Every
time the REC/OTR button on the remote control or the
RECORD button on the front panel pressed during
recording, the recording time will be increased by 30 minutes up to 8 hours.The recording automatically stops
when the recording time you set is reached.
Dubbing mode:
You can copy a DVD disc to a videotape or copy a videotape to a DVD disc.This function will be possible only if
the DVD disc is not copy protected.
REC MONITOR:
You can confirm the picture quality for recording in the
current recording speed which you set.
If you want to change the recording speed, press REC
SPEED button to set the desired recording mode.
Automatic Chapter marker setting:
Chapter markers will be put on recordings as you set in
SETUP menu before attempting to record.
Automatic Title menu making:
The unit makes title menus automatically when finalizing
the disc which are recorded in Video mode.
Automatic PLAYLIST making (VR mode):
A Playlist will be prepared from an Original list, so that
you can edit titles in a Playlist as you prefer.
An Original list is kept as it is.
DVD mode
VCR modeDVD mode
Play
Theater surround sound in your home:
When connecting the unit to an amplifier or a decoder which is
compatible with Dolby Digital, you are allowed to experience the
theater surround sound from discs with surround sound system.
Quick search for what you want to watch:
You can easily find the part you want to watch using search function. Search for a desired point on a disc by title, chapter, or time.
Start to play from Original and Playlist (VR mode):
Title playing is available from either an Original list or Playlist.
Quick search for what you want to watch:
You can easily find the part you want to watch using Index
search/Time search functions.An index mark will be assigned at
the beginning of each recordings you make. For Time search function, you can go to a specific point on a tape by entering the
exact amount of time you wish to skip.
Editing
Setting/Clearing chapter markers:
You can easily add chapter markers anywhere in your
recordings for easy editing. (VR mode)
Making your own Playlist:
With the original remains as it is, you can edit titles on
Playlist variously as you prefer.
Putting names on titles.
Setting pictures for thumbnails.
Setting/clearing chapter markers.
Deleting parts of titles, etc.
Protecting titles:
To avoid erasing titles, the protect function is useful when
it is ON in the original list.
Compatibility
Available for playing discs recorded in Video mode
on a regular DVD player (Video mode):
Discs recorded in the Video mode can be played on regular
DVD players, including computer DVD drives compatible with
DVD-Video playback*.You will need to finalize the discs
recorded in Video mode to play in other DVD players.
* DVD-Video Format (Video mode) is a new format for recording on DVDR/RW discs that was approved by the DVD Forum in 2000. Adoption of this format is optional for manufactures of DVD playback devices, and there are DVDVideo players, DVD-ROM drives or other DVD playback devices that do not
play DVD-R/RW discs recorded in the DVD-Video Format.
DVD mode
DVD mode
VCR mode
DVD mode
Followings are what you can do with this unit.
Manufactured under license from Dolby Laboratories.“Dolby” and the double-D symbol are trademarks of
Dolby Laboratories.
Functional overview
Before you start
Recording
Playing discs Editing
Before you start
Connections Getting started
Changing the SETUP menu
VCR functions Others
Español
7
Front Panel
POWER
REW F.FWD PLAY RECORD CHANNEL DUBBING SELECT STOP PLAY RECORD
S-VIDEO VIDEO L - AUDIO - R
OPEN/CLOSE
STOP/EJECT
VCR DVD
SELECT
1
222120
19
2
18
17 1215 14 91011
534
16 13 8 7 6
1.POWER button / indicator (DVD/VCR)
Press to turn the unit on and off.
If timer programmings have been set, press to set the
unit in timer-standby mode. Press to cancel the timer
standby mode, and turn the unit on.
Lights up when power is on.
2. Cassette compartment (VCR)
Insert a tape here.
3. A OPEN/CLOSE button (DVD)
Press to open or close the disc tray.
4. Select {Bbutton (DVD/VCR)
Press to select the component you wish to operate.
5.Disc tray (DVD)
Place a disc when open.
6.AUDIO INPUT jacks (LINE2) (DVD/VCR)
Use to connect external equipment with standard audio cables.
7.VIDEO INPUT jack (LINE2) (DVD/VCR)
Use to connect external equipment with a standard video cable.
8. S-VIDEO INPUT jack (LINE2) (DVD only)
Use to connect the S-Video output of external equipment with an S-Video cable.
9. RECORD button (DVD)
Press to start recording.
Press repeatedly to start a One-Touch Recording.
10. PLAY button (DVD)
Press to start or resume play.
11.STOP button (DVD)
Press to stop playback or recording.
Press to cancel the proceeding timer recording in DVD.
12.DVD SELECT indicator
This indicator appears when the DVD output mode is selected.
13. VCR SELECT indicator
This indicator appears when the VCR output mode is selected.
14. DUBBING button (DVD/VCR)
Press to start VCR to DVD (DVD to VCR) duplication
which you set in the SETUP menu.
15. CHANNEL L / K button (DVD/VCR)
Press to change the channel up and down.
16. Display (DVD/VCR)
Refer to “Guide to Displays on the front panel” on page 12.
17. Remote control sensor (DVD/VCR)
Receive signals from your remote control so that you
can control the unit from a distance.
18. RECORD button (VCR)
Press once to start a recording. Press repeatedly to
start a One-Touch Recording.
19. PLAY button (VCR)
Press to start playback.
20.STOP/EJECT button (VCR)
EJECTbutton-
Press to remove the tape from the unit.
STOP button-Press to stop the tape motion.
Press to cancel the proceeding timer recording in VCR.
21.F.FWD button (VCR)
Press to rapidly advance the tape, or view the picture
rapidly in forward during playback. (Forward Search)
22. REW button (VCR)
Press to rewind the tape, or to view the picture rapidly
in reverse during the playback mode. (Rewind Search)
Rear Panel
DVD DVD/VCR
ANTENNA
IN
AUDIO OUTAUDIO IN
S-VIDEO
AUDIO
OUT
DIGITAL
AUDIO OUT
COAXIAL
COMPONENT
VIDEO OUT
VIDEO OUTVIDEO IN
LY
IN
OUT
C
B
CR
L
R
L
R
R
OUT
634521
7
10
98
1112
1.AC Power Cord (DVD/VCR)
Connect to a standard AC outlet to supply power to this unit.
2. S-VIDEO INPUT jack (LINE1)
(DVD only)
Use to connect the S-Video output of external equipment with an S-Video cable.
3.
COMPONENT VIDEO OUTPUT jacks (DVD only)
Use to connect a TV monitor with component video
inputs with component video cables.
4.AUDIO INPUT jacks (LINE1) (DVD/VCR)
Use to connect external equipment with standard
audio cables.
5.AUDIO OUTPUT jacks (DVD/VCR)
Use to connect a TV monitor,AV receiver or other
equipment with standard audio cables.
6. TV ANTENNA IN jack (DVD/VCR)
Use to connect an antenna.
7. TV ANTENNA OUT jack (DVD/VCR)
Use to connect an antenna cable to pass the signal
from the TV ANTENNA IN to your TV monitor.
8. VIDEO OUTPUT jack (DVD/VCR)
Use to connect a TV monitor,AV receiver or other
equipment with a standard video cable.
9. VIDEO INPUT jack (LINE1) (DVD/VCR)
Use to connect external equipment with a standard
video cable.
10. S-VIDEO OUTPUT jack (DVD only)
Use to connect the S-Video input of a TV monitor,AV
receiver or other equipment with an S-Video cable.
11.AUDIO OUTPUT jacks (DVD only)
Use to connect a TV monitor,AV receiver or other
equipment with standard audio cables.
12.COAXIAL DIGITAL AUDIO OUTPUT jack
(DVD only)
Use to connect an AV receiver, Dolby Digital
decorder or other equipment with a coaxial digital
input with a digital coaxial cable.
Note: Do not touch the inner pins of the jacks on the rear panel. Electrostatic discharge may cause perma-
nent damage to the unit.
•
These jacks are
useful only in
DVD mode.
Functional overview (cont’d)
Before you start
a One-Touch Recording.
7.
SETUP button (DVD/VCR)
Press to display the setup menu.
8.
REC MONITOR button (DVD)
Press to check the video to be
recorded before attempting.
9.
MENU/LIST button (DVD)
Press to display the Disc menu.
To change ORIGINAL and
PLAYLIST on the TV screen.
(VR mode only)
10.
TOP MENU button (DVD)
Press to display the top menu.
11. CLEAR/C-RESET button
(DVD/VCR)
• DVD mode
Press to clear the password once
entered or to cancel the programming for CD or to clear the
selecting marker number in the
marker setup mode or to clear
the program once entered in the
timer recording setting mode,etc.
• VCR mode
Press to reset the tape counter.
12.
SEARCH MODE button (VCR)
To call up the index or time
search menu.
13. CM SKIP button (DVD)
During playback, press to skip
the 30 seconds.
14. REC SPEED button
(DVD/VCR)
Press to switch the recording
speed.
15.
OPEN/CLOSE A button (DVD)
Press to open or close the
disc tray.
16. AUDIO button (VCR)
During playback a HiFi video
tape, press to change the
AUDIO OUT setting “HiFi”
and “MONO”.
17.
CH K / L buttons (DVD/VCR)
• DVD mode
Press to change the channel
up and down.
• VCR mode
Press to change the channel
up and down.
Press to adjust the tracking
during playback or in slow
motion of the tape. Or while
playback is in still mode,
adjust the picture blurred vertically.
18.
VIDEO/TV button (DVD/VCR)
Press to select VIDEO or TV
position.
1.
POWER button (DVD/VCR)
Press to turn the unit on and off.
If timer programmings have
been set, press to set the unit
in timer-standby mode. Press
to cancel the timer standby
mode, and turn the unit on.
2.
Number buttons (DVD/VCR)
Press to select channel numbers.
Press to select a title/chapter/track on display or a TV
channel.
Or press to enter values for the
settings in the SETUP menu.
3.
DISPLAY button (DVD/VCR)
Press to display or change the
on-screen display.
4. VCR button
Press to activate the remote
control in VCR mode. (Refer
to page 9)
Press to select the VCR output mode.
5. E button (DVD/VCR)
• DVD mode
During playback, press to play
fast reverse.
Or during playback is paused,
press to play slow reverse.
• VCR mode
Press to rewind the tape, or
to view the picture rapidly in
reverse during the playback
mode.
6.
REC/OTR button (DVD/VCR)
Press once to start a recording. Press repeatedly to start
19. SLOW button (VCR)
During playback, press to
view the video tape in slow
motion.
20. PAUSE F button
(DVD/VCR)
Press to pause play or
recording.
21. DVD button
Press to activate the remote
control in DVD mode. (Refer
to page 9)
Press to select the DVD output mode.
22. PLAY B button
(DVD/VCR)
Press to start or resume play.
23. D button (DVD/VCR)
• DVD mode
During playback, press to play
fast forward.
• VCR mode
Press to rapidly advance the
tape, or view the picture
rapidly in forward during playback.
24.STOP C button
(DVD/VCR)
Press to stop playback or
recording.
25. TIMER PROG. button
(DVD/VCR)
Press to display the timer
program setting menu.
26. ENTER button
(DVD/VCR)
Press to confirm or select
menu items.
27. K / L / { / B buttons
(DVD/VCR)
Press to select items or settings.
28.RETURN button
(DVD/VCR)
Press to return to the previously displayed menu screen.
29. ZOOM button (DVD)
During playback, press to
enlarge the picture on the
screen.
30. SKIP H button (DVD)
During playback, press to skip to
the previous chapter or track.
Or during playback is paused,
press to play reverse step by step.
SKIP G button (DVD)
During playback, press to skip to
the next chapter or track.
Or during playback is paused,
press to play forward step by step.
Remote Control
8
POWER
1
2
3
4
5
6
7
8
9
10
11
12
13
REC SPEED
.@/:
123
GHI JKL MNO
456
PQRS
7809
DISPLAY
REC/OTR
REC MONITOR
MENU/LIST
CLEAR/C-RESET
SEARCH
MODE
OPEN/CLOSE
AUDIO
ABC DEF
TUV WXYZ
SPACE
VCR
DVD
PLAY
STOP
SETUP
TIMER PROG.
ENTER
TOP MENU
ZOOM SKIP SKIP
CM SKIP
CH
VIDEO/TV
SLOW
PAUSE
RETURN
14
15
17
18
19
21
23
25
27
28
29
30
16
20
22
24
26
Functional overview (cont’d)
Before you start
Recording
Playing discs Editing
Before you start
Connections Getting started
Changing the SETUP menu
VCR functions Others
Español
9
Using a remote control
Keep in mind the following when using the remote
control:
• Make sure that there is no obstacle between the
remote control and the remote sensor on the
unit.
• Use within the operating range and angle as
shown.
• Remote operation may become unreliable if strong
sunlight or fluorescent light is shining on the
remote sensor of the unit.
• Remote control for different devices can interfere
with each other. Avoid using remote control for
other equipment located close to the unit.
• Replace the batteries when you notice a fall off in
the operating range of the remote control.
S
K
I
P
R
E
C
P
A
U
S
E
P
E
N
T
E
R
M
E
N
U
P
L
A
Y
L
IS
T
O
P
M
E
N
U
/
O
R
I
G
I
N
A
L
k
K
F
W
D
g
S
T
O
P
C
P
L
A
Y
B
R
E
V
h
H
G
Installing batteries in the remote control
Install two AA batteries (supplied) matching the
polarity indicated inside battery compartment of the
remote control.
1
Note:
Incorrect use of batteries can result in hazards such
as leakage and bursting. Please observe the following:
• Do not mix new and old batteries together.
• Do not use different kinds of battery together,
although they may look similar, different batteries
may have different voltages.
• Make sure that the plus and minus ends of each
battery match the indications in the battery compartment.
•Remove batteries from equipment that is not going
to be used for a month or more.
• When disposing of used batteries, please comply
with governmental regulations or environmental
public instruction's rules that apply in your country
or area.
• Do not recharge, short-circuit, heat, burn or disassemble batteries.
2
3
VCR/DVD recorder Switching
Because this product is a combination of a VCR and a DVD recorder, you must select first which component you wish to operate with the SELECT button.
POWER
REW F.FWD PLAY RECORD CHANNEL DUBBING SELECT STOP PLAY RECORD
S-VIDEO VIDEO L - AUDIO - R
OPEN/CLOSE
STOP/EJECT
VCR DVD
SELECT
VCR DVD
SELECT
SELECT button
DVD SELECT
indicator
VCR SELECT
indicator
POWER
REC SPEED
AUDIO
ZOOM SKIP SKIP
OPEN/CLOSE
TOP MENU
SPACE
VCR
SETUP
CM SKIP
TIMER PROG.
RETURN
123
456
7809
STOP
PLAY
CH
VIDEO/TV
SLOW
PAUSE
.@/:
ABC DEF
GHI JKL MNO
PQRS
REC/OTR
REC MONITOR
MENU/LIST
CLEAR/C-RESET
SEARCH
MODE
ENTER
DISPLAY
TUV WXYZ
DVD
DVD button
VCR button
Press the VCR button on the remote control.
(Verify that the VCR SELECT indicator is lit.)
VCR MODE
Note
• Pressing only the SELECT button on the front
panel DOES NOT switch the mode of the
remote control.You MUST select the correct
mode on the remote control.
• Pressing the SETUP or the TIMER PROG.
button switches the unit to the DVD mode.
Press the DVD button on the remote control.
(Verify that the DVD SELECT indicator is lit.)
DVD MODE
Within about
23feet (7m)
60˚
Remote
control
Functional overview (cont’d)
Before you start
10
Guide to Displays on screen menu
The unit uses the following types of display for most operations. SETUP/DISC/CD menu,Title list, and DISPLAY, which allows you to change the playing status of disc during play. DISPLAY also gives you some disc
information for checking the status of the disc.
SETUP/DISC/CD menu
Press SETUP button to display the setup main menu, then choose either of SETUP/DISC/CD by pressing K / L /
{ / B buttons. Then, press ENTER button to display each menu.
These provides entries to all main functions of the unit.
1.Playback:
To set up the unit to play discs as
you prefer.
2. Recording:
To set up the unit to record to
discs as you prefer.
3. Display:
To set up the OSD screen and the
front display of the unit as you
prefer.
4. Select Video:
To choose a line input to record
to DVD discs from other video
equipment.
5. Clock:
To set up the clock of the unit as
you need.
6. Channel:
To make the channel setting of
the unit as you prefer.
1. Edit:
Turns on a title list, (When a disc
with VR mode is inserted,
'Original' or 'PlayList' is available.),
which shows the recorded titles
on the disc.
2. Format:
Allows you to erase all of the
recorded content on the disc.
The disc will be completely blank.
3. Finalize:
Allows you to finalize a disc
recorded titles.
4. Disc Protect (VR mode
only) :
Allows you to protect a disc from
accidental editing or recording.
1. Random Play:
To set the random play programming.
2. Program Play(Audio CD
only):
To set the program playing.
“CD” is available only when an
Audio CD disc or a CD-R/RW
disc with MP3 files is inserted
into the unit.
“SETUP” is available only in the
Stop mode.
“DISC” is available only when a DVD-R/RW disc is
inserted into the unit. When playing back a DVDVideo disc (commercially available) or the finalized
DVD-R disc, you cannot select “DISC”.
Setup Menu
Setup
1 2 3
4 5 6
Playback Setting
Disc Setting
Disc
Edit
Format
Finalize
Disc Protect OFF ON
1 2 3
4
CD Playback Mode
CD Playback Mode
Random Play
Program Play
1 2
Functional overview (cont’d)
Before you start
Recording
Playing discs Editing
Before you start
Connections Getting started
Changing the SETUP menu
VCR functions Others
Español
11
DISPLAY menu
First:
Press DISPLAY button to call up
the display menu.This menu will
give you the information on the
playing disc. Some operations are
available while disc is playing.
Details are on page 41.
1. Indicates a disc type and a
format mode.
2. Indicates a recording mode
and possible recording time.
3. Indicates a current channel
number.
4. Indicates a title number, chap-
ter number, and the time
elapsed of disc play.
5. Each icon means:
)
DVD mode
First:
Press DISPLAY button to call up
the display menu.
1. Playback status of the current
tape.
2. Indicates a current channel
number.
3. Indicates a recording speed
only five seconds.
4. Indicates a Tape Counter.
5. Audio status of the current
tape.
VCR mode
DVD
: Search
: Audio
: Subtitle
: Angle (except VR mode
: Repeat
: Marker
: Noise Reduction
: Zoom
4
11 00:00:00
5
1
DVD-RW
Video mode
SP 1:25 Rem.
CH 1
VCR
1
2
CH21
2
3
0:00:00 HIFISP
4 53
Functional overview (cont’d)
Before you start
12
Guide to Displays on the front panel
1. Current status of the unit
: Appears when a disc play
is paused.
: Appears when playing a
disc.
: Appears when the timer
programming has been
set and is proceeding.
: Appears during recording
process.
:
Appears during repeat
play.
:
Appears when a tape is in
the unit.
2. Disc type and Current
status of the unit
:
Appears when an audio CD
or a disc with MP3 files is
inserted in the disc tray.
:
Appears when a DVD disc
is inserted in the disc tray.
Appears when the timer
recording is proceeding in
DVD.
Appears when DVD is in
the timer recording standby mode.
:
Appears when a DVD-R disc
is inserted in the disc tray.
:
Appears when a DVDRW disc is inserted in
the disc tray.
:
Appears when the timer
recording is proceeding in
VCR.
Appears when VCR is in
the timer recording standby mode.
:
Appears during VCR to DVD
duplication process.
:
Appears during DVD to VCR
duplication process.
Display message
3. Recording speed
Indicates the recording speed of
the disc.
4. Title/Track and Chapter
mark
: Appears when indicating
a title/track number.
: Appears when indicating
a chapter number.
5. Displays the following
•Playing time / remaining time
• Current title / chapter / track
number
• Recording time
• Clock
• Channel number
• VCR tape counter
•OTR remaining time
6. : Appears in the after-
noon with the clock
displaying.
1. Appears when the disc tray is
opening.
2. Appears when the disc tray is
closing or close.
3. Appears when a disc is loading
in the disc tray.
4. Appears when recording data
is writing on to the disc.
1
6
3
5
2
4
1
2
3
4
VCR functions Others
Español
Connection to a TV
Connections
Recording
Playing discs Editing
Before you start
Connections Getting started
Changing the SETUP menu
13
DVD DVD/VCR
ANTENNA
IN
AUDIO OUTAUDIO IN
S-VIDEO
AUDIO
OUT
DIGITAL
AUDIO OUT
COAXIAL
COMPONENT
VIDEO OUT
VIDEO OUTVIDEO IN
LY
IN
OUT
C
B
CR
L
R
L
R
R
OUT
(Back of TV)
Plug in the AC power cord of this unit.
or
Cable
Signal
or
Cable
Signal
Connect
Disconnect
Antenna
Antenna
(Back of this unit)
(Back of TV)
RF Cable
(supplied)
Connect
3
2
1
4
Make one of the following connections, depending on the capabilities of your existing equipment.
DVDDVD/VCR
ANTENNAINAUDIO OUTAUDIO IN
S-VIDEO
AUDIO
OUT
COMPONENT
VIDEO OUT
VIDEO OUTVIDEO IN
LY
IN
OUT
C
B
C
R
L
R
L
R
R
OUT
DVDDVD/VCR
ANTENNAINAUDIO OUTAUDIO IN
S-VIDEO
AUDIO
OUT
DIGITAL
AUDIO OUT
COAXIAL
COMPONENT
VIDEO OUT
VIDEO OUTVIDEO IN
LY
IN
OUT
C
B
C
R
L
R
L
R
R
OUT
DVD
DVD/VCR
AUDIO OUT
L
R
DVD/VCR
VIDEO OUT
or
DVD
S-VIDEO
OUT
DVD
COMPONENT
VIDEO OUT
Y
C
B
C
R
AUDIO
OUT
L
R
AUDIO IN VIDEO IN
S-VIDEO IN
C
B
Y
C
R
COMPONENT
VIDEO IN
AUDIO OUT
TV
Basic Audio
Method 2 Method 3
Better picture Best picture
S-VIDEO OUT
COMPONENT VIDEO OUT
Audio cable
(supplied)
Component
Video cables
(commercially
available)
This unit
Note
• Connect this unit directly to the TV. If the A/V cables are connected to a VCR, pictures may be distorted
due to the copy protection system.
• Method 2 and method 3 are only useful in DVD mode.
Method 1
Good picture
VIDEO OUT
Video
cable
(supplied)
S-Video
cable
(commercially
available)
•
These jacks are
useful only in DVD
mode.
Connections
14
DVD/VCR
ANTENNA
IN
OUT
RF Cable
(supplied)
(Back of this unit)
IN
OUT
E
(Back of TV)
Cable
Signal
Connection A
(Cable box or
Satellite box)
Connection to a cable box or satellite box
Note to the Cable TV System Installer :
This reminder is provided to call the Cable TV system installer’s attention to Article 820-40 of the
National Electrical Code, which provides guidelines for proper grounding - in particular, specifying that the
cable ground shall be connected to the grounding system of the building, as close to the point of cable
entry as possible.
Select this connection when you want to view or record a scrambled channel.With this connection, channels
cannot be changed on this unit.You can view or record ONLY the channels you have selected on the cable
box or the satellite box.
• While you are recording, only the recorded channel can be viewed.
T
o select channels of the cable box or satellite box
1) Turn on this unit by pressing POWER button.The “POWER” indicator on the front panel will appear.
Then, press the CHANNEL buttons to select channel 3 or 4 (the same channel as the output channel of
the cable box or satellite box).
• If noise appears on the TV screen
,press VIDEO/TV button on the remote control.
• If you use the channel 4, you need to change this unit’s RF output to channel 4. Refer to “RF converter
output” on page 100.
2) At the TV, select channel 3 or 4 (the same channel as you have selected at step 1).
3) At the cable box or satellite box, select the channel you want to view or record.
DVD/VCR
ANTENNA
IN
OUT
RF Cable (supplied)
RF Cable
(Back of TV)
IN
OUT
(Cable box or
Satellite box)
E
Cable
Signal
Connection B
(Back of this unit)
Select this connection when you want to change channels on this unit.With this connection, you may watch
one channel while recording another.
• You may not view or record a scrambled channel.
T
o select channels of the cable box or satellite box
1) At the cable box or satellite box, select channel 3 or 4 (the same channel as this unit’s RF output channel.)
• Refer to “RF converter output” on page 100.
2) At the TV, select the same channel as the output channel (3 or 4) of the cable box or satellite box.
3) Turn on this unit by pressing POWER button. The “POWER” indicator on the front panel will appear.
Then, select the channel you want to view or record.
• If noise appears on the TV screen
,press VIDEO/TV button on the remote control.
To playback a DVD disc or a tape
Follow the steps 1) to 2) above.Then, playback a DVD disc or a tape.
• Refer to “Playback” on pages 44-45, 94.
T
o view one channel while recording another
1) While you are recording on this unit, press VIDEO/TV button.
2) At the cable box or satellite box, select the channel you want to view.
VCR functions Others
Español
Connection to an Audio System
Connections
Recording
Playing discs Editing
Before you start
Connections Getting started
Changing the SETUP menu
15
• When you change the connections, all devices should be turned off.
• Refer to each owner’s manual for further information on other devices.
or
L
L
R
R
DVD
DVD/VCR
AUDIO OUT
AUDIO
OUT
Stereo system
COAXIAL
DVD
DIGITAL
AUDIO OUT
COAXIAL
AUDIO
Method 1
Analog audio
input jacks
Digital audio
input jack
AUDIO OUT
DIGITAL
AUDIO OUT
Method 2
Audio cable
(supplied)
Audio Coaxial
Digital cable
(commercially
available)
Note
• If output is Dolby Digital encoded audio, connect
to a Dolby Digital decoder, and set “Dolby Digital”
to “Stream” for the “Digital Out” setting in the
SETUP menu. (Refer to pages 90-91.)
• The audio source on a disc in a Dolby Digital 5.1
channel surround format cannot be recorded as
digital sound by an MD or DAT deck.
• Unless connected to a Dolby Digital decoder, set
“Dolby Digital” to “PCM” for the “Digital Out” setting in the SETUP menu. Playing a DVD using incorrect settings may generate noise distortion, and may
also damage the speakers. (Refer to pages 90-91.)
• Set “Dolby Digital” to “PCM” for the “Digital Out”
setting in the SETUP menu for connecting to an
MD deck or DAT deck. (Refer to pages 90-91.)
• By hooking this unit up to a Multi-channel Dolby
Digital decoder, you can enjoy high-quality Dolby
Digital 5.1 channel surround sound as heard in the
movie theaters.
Dolby Digital decoder,
MD deck or DAT deck
This unit
Easy DVD recording
Getting started
16
The following will help you to understand easily how to record to DVD discs.
Note:
Make sure batteries are in the remote control and you have connected this unit and the TV correctly.
Step 1: Choose a disc type
There are several types of DVD disc recordable
to choose from. Choose an applicable type by
“DVD disc types” on this page.
This unit can record on the following type of
discs.
For example, when you want to record repeatedly on the same disc, or when you want to edit the
disc after recording, select the rewritable DVDRW type disc.
When you want to save recordings without any
alteration, a non-rewritable DVD-R can be your
choice.
Step 2:
Insert a blank disc
Remote Control
Open the
disc tray
Close the
disc tray
Format the disc
Insert the disc in the unit.
Then, format the disc from
SETUP menu.Video format
(Video mode) or Video
recording format (VR mode)
will be available depending on
the disc type inserted.This is
necessary to prepare the disc
for recording. Details are on
pages 28-30.
DVD disc types
.
DVD-RW VR DVD-RW Video
You want to
Record TV programs
Reuse by deleting unwanted contents
Edit recorded contents
Edit/Record from connected equipment
Copy discs for distribution
Play on other DVD equipment
*1
*1
DVD-RW VR DVD-RW Video
Features
Recording
Rewritable? Yes Yes
Can create chapters at fixed intervals (auto.) Yes Yes
Can create chapters wherever you like (manual) Yes No
Can record 16:9 size pictures Yes Yes
Can record Copy-Once programs Yes No
Editing
Can perform basic edit functions Yes Yes
Can perform advanced edit functions (Playlist edit) Yes No
No
Ye s
No
Ye s
No
No
No
*1
DVD-RW (VR mode) can only be played on DVD
equipment that is VR compatible.
Note:
For details of the above functions and implied
restrictions, see the explanations inside the manual.
DVD-R
DVD-R
: Most suitable. : Can be used. : Some functions are limited. : Cannot be used.
2
Turn on
the unit
1
3
Loading
This operation may take a
while to be recognized.
REC SPEED
ABC DEF
AUDIO
OPEN/CLOSE
CH
POWER
.@/:
123
GHI JKL MNO
REC SPEED
ABC DEF
AUDIO
OPEN/CLOSE
CH
POWER
.@/:
123
GHI JKL MNO
VCR functions Others
Español
Easy DVD recording (Cont’d)
Getting started
Recording
Playing discs Editing
Before you start
Connections Getting started
Changing the SETUP menu
17
Step 3: Select the
Recording
speed
Step 5: Record to
DVD discs
123
Step 4: Select the
desired
channel
Step 6: Stop the
Record
VIDEO/TV
PQRS
TUV WXYZ
Hint 1: Play the recorded contents
You can select the title you want to play from a displayed menu, and immediately start to play. Recorded contents are very accessible on a disc, the procedure is simple really as you choose a
title on a chapter from the menu
screen.
What is titles and chapters?
The contents of DVD disc are generally
divided into some titles.Titles may be
further subdivided into chapters.
Hint 2: Edit the recorded disc
You will find editing discs very easy, and the unit offers convenient edit functions, which are possible only with DVD-R/RW discs.
You can edit the following from a title list.
• Putting names on titles
• Setting pictures for thumbnails (VR mode)
• Setting/clearing chapter markers
• Deleting parts of titles (VR mode)
Original and Playlist (VR mode)
You can edit the recordings in Playlist without changing the original recordings.Any Playlist does not take up much disc space.
What “Original” or “Playlist” is for?
Throughout this manual, you will find Original and Playlist to refer to the actual
content and the edited version.
• Original content refers to what’s actually recorded on the disc.
• Playlist content refers to the edited version of the disc; how the Original
content is to be played.
This operation may
take a while to be
completed.
To select the DVD mode
1
To select the recording
speed
2
1
2
REC SPEED
ABC DEF
TUV WXYZ
SPACE
VCR
AUDIO
DVD
OPEN/CLOSE
CH
VIDEO/TV
SLOW
PAUSE
POWER
.@/:
123
GHI JKL MNO
456
PQRS
7809
DISPLAY
REC SPEED
ABC DEF
TUV WXYZ
SPACE
VCR
AUDIO
DVD
OPEN/CLOSE
CH
VIDEO/TV
SLOW
PAUSE
POWER
.@/:
123
GHI JKL MNO
456
PQRS
7809
DISPLAY
SP 2:01 Rem.
CH 1
Start Rec. Stop/Start Stop Rec.
Title 1 Title 2
Chapter 1 Chapter 1Chapter 2 Chapter 3 Chapter 2
GHI JKL MNO
456
PQRS
7809
DISPLAY
REC/OTR
REC MONITOR
I
TUV WXYZ
SPACE
VCR
SETUP
CH
VIDEO/TV
SLOW
DVD
PAUSE
PLAY
STOP
TIMER PROG.
ENTER
7809
DISPLAY
REC/OTR
SPACE
SETUP
SLOW
VCR
PAUSE
DVD
PLAY
STOP
TIMER PROG.
Writing to Disc
58%
Channel setting
Getting started
18
All channels are stored in the unit
when purchased.We recommend
that you get available channels in
your area stored using “Auto
Preset” in the Channel Preset of
the SETUP menu.
Getting channels automatically
1
Press POWER button to turn
on the unit.
2
Turn the TV on and be sure
to select the input to which
the unit is connected.
3
Press SETUP button to display SETUP/DISC menu.
SETUP/DISC menu will appear.
Screen:
4
Select SETUP using { / B
buttons, then press ENTER
button.
SETUP menu will appear.
5
Select “Channel” using K / L
/ { / B buttons, then press
ENTER button.
Channel Preset menu will appear.
6
Select “Auto Preset” using K
/ L buttons, then press
ENTER button.
The unit will start getting channels available in your area.
7
Press SETUP button to exit.
•You can select only the channels
memorized in this unit by using
the CHANNEL buttons.
Note
• If the auto presetting is cancelled during presetting, some
channels not yet preset may
not be received.
• The selection will depend on
how you receive the TV channels.
To cancel the auto presetting during scanning:
Press RETURN button or
SETUP button to cancel.
To select a channel
You can select a channel by
directly entering channel using
the Number buttons on the
remote control.
Notes for using the
Number buttons:
• When selecting cable channels
which are higher than 99,
enter channel numbers as a
three-digit number.(For example: 117, press 1,1,7)
• You must precede single-digit
channel numbers with a zero
(For example: 02, 03, 04 and
so on).
•
You can select the line input
mode (“L1” or “L2”).To select
“L1” by pressing [0],[0],[1].To
select “L2” by pressing
[0],[0],[2].Details are on page 38.
POWER
REC SPEED
AUDIO
ZOOM SKIP SKIP
OPEN/CLOSE
TOP MENU
SPACE
VCR
SETUP
CM SKIP
TIMER PROG.
RETURN
123
456
7809
STOP
PLAY
CH
VIDEO/TV
SLOW
PAUSE
.@/:
ABC DEF
GHI JKL MNO
PQRS
REC/OTR
REC MONITOR
MENU/LIST
CLEAR/C-RESET
SEARCH
MODE
ENTER
DISPLAY
TUV WXYZ
DVD
3
4
5
6
1
7
Setup
Setup Menu
Playback Setting
Setup > Channel Preset
Auto Preset
Manual Preset
TV Audio Select
VCR DVD
Stereo
CH 18
Auto Presetting Now
VCR functions Others
Español
Channel setting (cont’d)
Getting started
Recording
Playing discs Editing
Before you start
Connections Getting started
Changing the SETUP menu
19
4
Select “Manual Preset” using
K / L buttons, then press
ENTER button.
Manual Preset menu will appear.
5
Select the channel number to
add or delete.
Press { button to move to a
lower channel number.
Press B button to move to a
higher channel number.
6
Select “Add” or “Delete”
using K / L buttons, then
press ENTER button.
The channel number will be
added or deleted from a channel
memory.Then a next channel
number will appear so that you
can continue adding or deleting
channels.
7
Press SETUP button to exit.
Adding/deleting channels
The channels you no longer
receive or seldom watch can be
deleted from the memory.You also
may add channels into memory.
1
Press SETUP button to display SETUP/DISC menu.
SETUP/DISC menu will appear.
Screen:
2
Select SETUP using { / B
buttons, then press ENTER
button.
SETUP menu will appear.
3
Select “Channel” using K / L
/ { / B buttons, then press
ENTER button.
Channel Preset menu will appear.
1
2
3
4
5
7
6
Setup Menu
Setup
Setup > Channel Preset > Manual Preset
CH2
Add
Delete
Setup > Channel Preset > Manual Preset
CH18
Add
Delete
POWER
REC SPEED
.@/:
ABC DEF
123
GHI JKL MNO
456
PQRS
TUV WXYZ
7809
SPACE
VCR
DISPLAY
PLAY
STOP
SETUP
REC/OTR
REC MONITOR
MENU/LIST
TOP MENU
ZOOM SKIP SKIP
CLEAR/C-RESET
SEARCH
CM SKIP
MODE
AUDIO
DVD
ENTER
OPEN/CLOSE
CH
VIDEO/TV
SLOW
PAUSE
TIMER PROG.
RETURN
Playback Setting
Setup > Channel Preset
Auto Preset
Manual Preset
TV Audio Select
VCR DVD
Stereo
Selecting the TV stereo or SAP
Getting started
20
You can select a sound channel to
output from TV. “Stereo” has
been selected as the default.
1
Press SETUP button to display SETUP/DISC menu.
SETUP/DISC menu will appear.
Screen:
2
Select SETUP using { / B
buttons, then press ENTER
button.
SETUP menu will appear.
3
Select “Channel Preset”
using K / L / { / B buttons,
then press ENTER button.
Channel Preset menu will appear.
4
Select “TV Audio Select”
using K / L buttons, then
press ENTER button.
Option window will appear.
5
Select “Stereo” or “SAP”
using K / L buttons, then
press ENTER button.
Stereo:
Outputs main-audio.
SAP:
(Secondary Audio Program)
Outputs sub-audio.
Refer to the item in “Glossary”
on page 102 for more information.
6
Press SETUP button to exit.
1
2
3
4
5
6
Setup Menu
Setup
Setup > Channel Preset
Auto Preset
Manual Preset
TV Audio Select
VCR DVD
Stereo
Stereo
SAP
POWER
REC SPEED
.@/:
ABC DEF
123
GHI JKL MNO
456
PQRS
TUV WXYZ
7809
SPACE
VCR
DISPLAY
PLAY
STOP
SETUP
REC/OTR
REC MONITOR
MENU/LIST
TOP MENU
ZOOM SKIP SKIP
CLEAR/C-RESET
SEARCH
CM SKIP
MODE
AUDIO
DVD
ENTER
OPEN/CLOSE
CH
VIDEO/TV
SLOW
PAUSE
TIMER PROG.
RETURN
Playback Setting
Setup > Channel Preset
Auto Preset
Manual Preset
TV Audio Select
VCR DVD
Stereo
VCR functions Others
Español
Clock setting
Getting started
Recording
Playing discs Editing
Before you start
Connections Getting started
Changing the SETUP menu
21
Set the clock before you try the
timer recording. If a Public
Broadcasting Station (PBS) is available
in your area, follow Auto Clock
Setting below. If not, follow Manual
Clock Setting on pages 22-23.
Auto Clock Setting
Make sure
• The antenna/cable TV connections are correct.
• If this unit is connected to a
Cable Box or Satellite Box, select
the local PBS station on them to
set the clock automatically.
1
Press SETUP button to display SETUP/DISC menu.
SETUP/DISC menu will appear.
Screen:
2
Select SETUP using
{ / B
but-
tons, then press ENTER button.
SETUP menu will appear.
3
Select “Clock” using
K / L / { / B
buttons, then press ENTER button.
Clock menu will appear.
4
Select “Auto Clock Setting”
using K / L buttons, then
press ENTER button.
Option window will appear.
5
• If you do not know your
PBS channel number, select
“Auto” using K / L buttons,
then press ENTER button.
• If you know your PBS channel number, select “Manual”
using K / L buttons, then
press ENTER button.
Enter your PBS channel
number using Number or K
/ L buttons, then press
ENTER button.
6
Press SETUP button to exit.
7
Press POWER button to turn
off the unit.
This unit will search for the time
only when the power is off. Leave
it off for several minutes to give
this unit time to set the clock on
the display of the front panel.
Note
• The clock may set itself automatically after you connect the
antenna/cable signal to this
unit and plug in the power
cord. In this case, the current
time will appear on the display
of the front panel.
• If the current time is not displayed or the displayed clock
is not correct, set the clock
manually.
POWER
REC SPEED
AUDIO
ZOOM SKIP SKIP
OPEN/CLOSE
TOP MENU
SPACE
VCR
SETUP
CM SKIP
TIMER PROG.
RETURN
123
456
7809
STOP
PLAY
CH
VIDEO/TV
SLOW
PAUSE
.@/:
ABC DEF
GHI JKL MNO
PQRS
REC/OTR
REC MONITOR
MENU/LIST
CLEAR/C-RESET
SEARCH
MODE
ENTER
DISPLAY
TUV WXYZ
DVD
1
2
3
4
5
6
7
Setup > Clock
Clock Setting
Auto Clock Setting
Daylight Saving Time
VCR DV D
OFF
Auto
Auto
Manual
Off
Setup Menu
Setup
Playback Setting
Setup > Clock
Clock Setting
Auto Clock Setting
Daylight Saving Time
VCR DV D
Auto
ON
Setup > Clock
Clock Setting
Auto Clock Setting
Daylight Saving Time
VCR DV D
OFF
Set Channel No.
Auto
Auto
CH1
Manual
Off
Clock setting (cont’d)
Getting started
22
Manual Clock Setting
1
Press SETUP button to display SETUP/DISC menu.
SETUP/DISC menu will appear.
Screen:
2
Select SETUP using { / B
buttons, then press ENTER
button.
SETUP menu will appear.
3
Select “Clock” using K / L /
{ / B buttons, then press
ENTER button.
Clock menu will appear.
4
Select “Clock Setting” using
K / L buttons, then press
ENTER button.
A clock setting window will
appear.
Press ENTER button again.
Default date will appear.
5
Enter the date (month / day /
year) using K / L buttons.
Press { / B buttons to move
the cursor.
6
Enter the time (hour /
minute) using K / L buttons.
Press { / B buttons to move
the cursor.
Note
•
Your clock setting will be lost if
either there is a power failure
or this unit has been unplugged
for more than 30 seconds
when you set the clock manually.
POWER
REC SPEED
AUDIO
ZOOM SKIP SKIP
OPEN/CLOSE
TOP MENU
SPACE
VCR
SETUP
CM SKIP
TIMER PROG.
RETURN
123
456
7809
STOP
PLAY
CH
VIDEO/TV
SLOW
PAUSE
.@/:
ABC DEF
GHI JKL MNO
PQRS
REC/OTR
REC MONITOR
MENU/LIST
CLEAR/C-RESET
SEARCH
MODE
ENTER
DISPLAY
TUV WXYZ
DVD
1
2
3
4
5
6
Setup Menu
Setup
Playback Setting
Setup > Clock
Clock Setting
Auto Clock Setting
Daylight Saving Time
VCR DV D
Auto
ON
- - : - -
VCR DV D
Auto
ON
Setup > Clock
Clock Setting
Auto Clock Setting
Daylight Saving Time
- - - / - - / - - - - ( - - - )
12 : 00AM
VCR DV D
Auto
ON
Setup > Clock
Clock Setting
Auto Clock Setting
Daylight Saving Time
JAN / 12 / 2004 (MON)
09 : 24 AM
VCR DV D
Auto
ON
Setup > Clock
Clock Setting
Auto Clock Setting
Daylight Saving Time
JAN / 12 / 2004 (MON)
VCR functions Others
Español
Clock setting (cont’d)
Recording
Playing discs Editing
Before you start
Connections Getting started
Changing the SETUP menu
Getting started
23
7
Press K / L buttons to select
AM or PM, then press ENTER
button.
Clock menu will appear, then the
settings will be activated.
8
Press SETUP button to exit.
Although seconds are not displayed,
they begin counting from zero.
POWER
REC SPEED
AUDIO
ZOOM SKIP SKIP
OPEN/CLOSE
TOP MENU
SPACE
VCR
SETUP
CM SKIP
TIMER PROG.
RETURN
123
456
7809
STOP
PLAY
CH
VIDEO/TV
SLOW
PAUSE
.@/:
ABC DEF
GHI JKL MNO
PQRS
REC/OTR
REC MONITOR
MENU/LIST
CLEAR/C-RESET
SEARCH
MODE
ENTER
DISPLAY
TUV WXYZ
DVD
8
7
4
ZOOM SKIP SKIP
TOP MENU
SETUP
CM SKIP
TIMER PROG.
RETURN
STOP
PLAY
REC/OTR
REC MONITOR
MENU/LIST
CLEAR/C-RESET
SEARCH
MODE
ENTER
6
5
4
Select “Auto Clock Setting”
using K / L buttons, then
press ENTER button.
Option window will appear.
Repeat steps (1) to (3) in “Manual Clock Setting”.
When “Auto Clock Setting” is selected to “Auto” or
“Manual”, change it to “OFF” as following steps.
5
Select “OFF” using K / L
buttons, then press ENTER
button.
6
Press SETUP button to exit.
Setup > Clock
Clock Setting
Auto Clock Setting
Daylight Saving Time
VCR DV D
Auto
ON
Setup > Clock
Clock Setting
Auto Clock Setting
Daylight Saving Time
VCR DV D
OFF
Auto
Auto
Manual
Off
Clock setting (cont’d)
Getting started
24
4
Select “Daylight Saving
Time” using K / L buttons,
then press ENTER button.
Daylight Saving Time options will
appear.
5
Select “ON” or “OFF” using
K / L buttons, then press
ENTER button.
Choose “ON” when currently
observing the daylight saving time.
6
Press SETUP button to exit.
Setting the daylight saving time
When Daylight Saving Time is
ON, the unit clock will automatically move forward one hour on
the first Sunday in April and move
back one hour on the last Sunday
in October.
1
Press SETUP button to display SETUP/DISC menu.
SETUP/DISC menu will appear.
Screen:
2
Select SETUP using { / B
buttons, then press ENTER
button.
SETUP menu will appear.
3
Select “Clock” using K / L /
{ / B buttons, then press
ENTER button.
Clock menu will appear.
1
2
3
4
5
6
Setup Menu
Setup > Clock
Clock Setting
Auto Clock Setting
Daylight Saving Time
VCR DV D
Auto
ON
OFF
POWER
REC SPEED
.@/:
ABC DEF
123
GHI JKL MNO
456
PQRS
TUV WXYZ
7809
SPACE
VCR
DISPLAY
PLAY
STOP
SETUP
REC/OTR
REC MONITOR
MENU/LIST
TOP MENU
ZOOM SKIP SKIP
CLEAR/C-RESET
SEARCH
CM SKIP
MODE
AUDIO
DVD
ENTER
OPEN/CLOSE
CH
VIDEO/TV
SLOW
PAUSE
TIMER PROG.
RETURN
Setup
Playback Setting
Setup > Clock
Clock Setting
Auto Clock Setting
Daylight Saving Time
VCR DV D
Auto
ON
VCR functions Others
Español
Selecting the TV aspect ratio
Getting started
Recording
Playing discs Editing
Before you start
Connections Getting started
Changing the SETUP menu
25
You can select the TV aspect ratio
to match the formats of what you
are playing with the unit and your
TV screen (4:3 standard or 16:9
widescreen TV).
“4:3 Letter Box” has been selected as the default.
1
Press SETUP button to display SETUP/DISC menu.
SETUP/DISC menu will appear.
Screen:
2
Select SETUP using { / B
buttons, then press ENTER
button.
SETUP menu will appear.
3
Select “Playback” using K / L
/ { / B buttons, then press
ENTER button.
Playback menu will appear.
4
Select “TV Aspect” using K /
L buttons, then press ENTER
button.
Option window will appear.
Refer to the Note on this
page.
5
Select a desired option using
K / L buttons, then press
ENTER button.
6
Press SETUP button to exit.
Note
If you have a standard TV:
Select “4:3 Letter Box”, so that
black bars appear on the top
and bottom of the screen.
Select “4:3 Pan & Scan” for a
full height picture with both
sides trimmed.
If you have a widescreen TV:
Select “16:9 Wide”.
POWER
REC SPEED
AUDIO
ZOOM SKIP SKIP
OPEN/CLOSE
TOP MENU
SPACE
VCR
SETUP
CM SKIP
TIMER PROG.
RETURN
123
456
7809
STOP
PLAY
CH
VIDEO/TV
SLOW
PAUSE
.@/:
ABC DEF
GHI JKL MNO
PQRS
REC/OTR
REC MONITOR
MENU/LIST
CLEAR/C-RESET
SEARCH
MODE
ENTER
DISPLAY
TUV WXYZ
DVD
1
2
3
4
5
6
Setup Menu
Setup
Setup > Playback
TV Aspect
Parental Lock
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
Dynamic Range Control
Fast Forward with Audio
DVD
4:3 Letter Box
All
English
Original
OFF
ON
OFF
Setup > Playback
TV Aspect
Parental Lock
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
Dynamic Range Control
Fast Forward with Audio
DVD
16:9 Wide
4:3 Letter Box
8
4:3 Pan & Scan
16:9 Wide
English
Original
OFF
ON
OFF
Playback Setting
26
Information on DVD recording
Recording
Information
This unit can record to DVD-R and DVD-RW discs.
When recording, you will need to select a recording
format between Video mode and VR mode depending on the disc format.The disc format for DVD-R
is always “Video format,” so a recording format will
be “Video mode”.
On the other hand, when recording to DVD-RW, a
recording format will be “Video mode” or “VR
mode” because a disc format is available between
“Video Recording format” and “Video format” for
DVD-RW.
About Video mode and VR (Video Recording)
mode
Video mode is the same recording format as DVDVideo discs purchased locally, so that you can play in
most DVD players.To play in other DVD players,
you will need to finalize (see page 39). Unless finalized, you can play, record additionally or edit discs
recorded in Video mode with this unit.
VR (Video Recording) mode is a basic recording
format for DVD-RW.You can record and edit
repeatedly.
DVD players with are capable of playing
DVD-RW recorded in VR mode.
Recording speed
You can select a recording speed among 6 options,
and the recording time will depend on the recording speed you select as follows.
* This table is designed for a new single-sided 12cm
disc as the standard.The recording time are estimates and actual recording time may differ.
* The audio and video quality is getting poorer as
the recording time becomes longer.
Restrictions on recording
You cannot record copy-protected video using this
unit. Copy-protected video includes DVD-Video
discs and some satellite broadcasts.
If copy-protected material is encountered during a
recording, recording will pause or stop automatically
and an error message will be displayed on-screen.
Video that is “copy-once only” can only be recorded
using a DVD-RW disc in VR mode with CPRM (see
below).
When recording a TV broadcast or through an
external input, you can display copy control information on screen.
What is “CPRM”?
CPRM is a copy protection system with scramble system regarding the recording of “copy
once” broadcast programs. CPRM stands for
Content Protection for Recordable Media.
This unit is CPRM compatible, which means
that you can record copy-once broadcast programs, but you cannot then make a copy of
those recordings. CPRM recordings can only be
made on DVD-RW discs formatted in VR
mode, and CPRM recordings can only be played
on players that are specifically compatible with
CPRM.
Logo Attributes
12cm, single-sided, single layer disc
Approx. max. recording time (SEP mode):
DVD-RW
DVD-R
Disc type Disc format
DVD-RW
DVD-R
600 minutes (4.7GB)
12cm, single-sided, single layer disc
Approx. max. recording time (SEP mode):
600 minutes (4.7GB)
Functions
Video mode
Video
DVD-RW
DVD-RW
VR mode
VR
DVD-RW
DVD-RW
Video mode
DVD-R
DVD-R
Playing, limited recording,
limited editing
Playing, recording,
Original/Playlist editing
Playing, limited recording,
limited editing
Recording
speed
XP (1H)
SP (2H)
LP (4H)
EP (6H)
SLP (8H)
SEP (10H)
Recording
time *
60 min
120 min
240 min
360 min
480 min
600 min
Video/Sound Quality
VCR functions Others
Español
27
Recording
Information on copy control
Some satellite broadcasts include copy-protected
information. For recording these, refer to the following.
Making discs playable in other DVD
player (Finalize)
You will need to finalize discs when in the following:
- when playing DVD-R/RW (Video mode) recorded
with this unit in other DVD players.
- when DVD-RW (VR mode) recorded with this
unit fails to be played in other RW compatible DVD
players.
• Once DVD-R/RW (Video mode) is finalized, you
cannot record additionally or edit.
•You can record additionally to or edit DVD-RW
(VR mode), which is finalized with this unit.
• Be sure to finalize discs recorded with this unit by
using this unit.
•Title menu will be created automatically in DVDR/RW (Video mode) finalized with this unit.
To play in other DVD players, finalize discs recorded
from this unit with the following condition.
Note
• The audio and video quality is getting poorer as
the Recording time becomes longer.
• This unit cannot record CD-R or CD-RW discs.
•DVD-R/RW and CD-R/RW discs recorded using
a personal computer or a DVD or CD recorder
may not play if the disc is damaged or dirty, or if
there is dirt of condensation on the unit’s lens.
• If you record a disc using a personal computer,
even if it is recorded in a compatible format,
there are cases in which it may not play because
of the settings of the application software used
to create the disc. (Check with the software publisher for more detailed information.)
Information on DVD recording (cont’d)
Recording
Playing discs Editing
Before you start
Connections Getting started
Changing the SETUP menu
Disc type/
format
VR mode
DVD-RW
ver.1.0
ver.1.1
ver.1.1 CPRM
compatible
Video mode
DVD-RW
ver.1.1
ver.1.1 CPRM
compatible
Video mode
DVD-R
ver.2.0
Recordable
Recordable only for DVD-RW ver.1.1 compatible
with CPRM
Not Recordable
Copy-free Copy-once
Copyprohibited
Disc type Mode
DVD-R
ver.2.0
DVD-RW
ver.1.1
ver.1.1 CPRM compatible
Video mode
Video mode
Settings for the recording format to a blank disc
28
Formatting a disc
Recording
When inserting a blank disc, the
unit starts to initialize the blank
disc.
After that,You can record to the
disc with the recording format
selected in SETUP menu.
You are allowed to set a specified
time for chapter marks.
1
Press SETUP button to display SETUP/DISC menu.
SETUP/DISC menu will appear.
Screen:
2
Select SETUP using { / B
buttons, then press ENTER
button.
SETUP menu will appear.
3
Select “Recording” using K /
L / { / B buttons, then press
ENTER button.
Recording menu will appear.
4
Select “DVD-RW Recording
Format” using K / L buttons,
then press ENTER button.
Option window will appear.
Video mode has been selected as
the default.
5
Select “Video mode” or “VR
mode” using K / L buttons,
then press ENTER button.
The recording mode will be set.
Note
• When inserting a blank
DVD+R or DVD+RW disc,
the error message ("Disc
Error") will appear.This unit is
not compatible with a
DVD+R/RW disc.
• If using a DVD-RW (ver 1.0)
disc, recording will start in VR
mode even you choose video
mode in SETUP menu.
POWER
REC SPEED
AUDIO
ZOOM SKIP SKIP
OPEN/CLOSE
TOP MENU
SPACE
VCR
SETUP
CM SKIP
TIMER PROG.
RETURN
123
456
7809
STOP
PLAY
CH
VIDEO/TV
SLOW
PAUSE
.@/:
ABC DEF
GHI JKL MNO
PQRS
REC/OTR
REC MONITOR
MENU/LIST
CLEAR/C-RESET
SEARCH
MODE
ENTER
DISPLAY
TUV WXYZ
DVD
1
2
3
4
5
Video
DVD-RW
DVD-RW
VR
DVD-RW
DVD-RW
Setup > Recording
DVD-RW Recording Format
Auto Chapter
Timer Programming
Dubbing Mode
DVD
Video mode
10 minutes
VCR DVD
Setup Menu
Setup
Playback Setting
Setup > Recording
DVD-RW Recording Format
Auto Chapter
Timer Programming
Dubbing Mode VCR DVD
Video mode
DVD Player Compatibility mode.
VR mode
Editing possibility mode.
DVD
Video mode
VR mode
VR mode
10 minutes
VCR functions Others
Español
29
Recording
Formatting a disc (cont’d)
Recording
Playing discs Editing
Before you start
Connections Getting started
Changing the SETUP menu
6
Select “Auto Chapter” using
K / L buttons, then press
ENTER button.
Option window will appear.
“10 minutes” has been selected as
the default.
7
Select a desired time option
using K / L buttons, then
press ENTER button.
Chapter marks will be put as you
specified.
8
Press SETUP button to exit
SETUP menu.
6
POWER
REC SPEED
AUDIO
ZOOM SKIP SKIP
OPEN/CLOSE
TOP MENU
SPACE
VCR
SETUP
CM SKIP
TIMER PROG.
RETURN
123
456
7809
STOP
PLAY
CH
VIDEO/TV
SLOW
PAUSE
.@/:
ABC DEF
GHI JKL MNO
PQRS
REC/OTR
REC MONITOR
MENU/LIST
CLEAR/C-RESET
SEARCH
MODE
ENTER
DISPLAY
TUV WXYZ
DVD
8
7
Note
• The time for chapter marks is
not accurate in Video mode.
Setup > Recording
DVD-RW Recording Format
Auto Chapter
Timer Programming
Dubbing Mode VCR DVD
DVD
VR mode
OFF
5 minutes
10 minutes
10 minutes
15 minutes
30 minutes
60 minutes
30
Formatting a disc (cont’d)
Recording
If you are using a DVD-RW disc,
by default it will be Video mode.
You can change this to VR mode
from SETUP menu.
1
Press SETUP button to display SETUP/DISC menu.
SETUP/DISC menu will appear.
Screen:
2
Select “DISC” using { / B but-
tons, then press ENTER button.
DISC menu will appear.
* VR mode only
3
Select “Format” using K / L
buttons, then press ENTER
button.
Option window will appear.
* VR mode only
4
Select “Yes” using { / B but-
tons, then press ENTER button.
Option window will appear.
* VR mode only
5
Select “Yes” using { / B but-
tons, then press ENTER button.
Formatting will start.
6
Formatting is complete.
100% will be indicated.
This operation may take a
while to be completed.
Reformatting a disc
Note
• When you reformat the disc,
the contents of the disc will
be erased.
• If you want to cancel format
at step 5, select “No”.
POWER
REC SPEED
AUDIO
ZOOM SKIP SKIP
OPEN/CLOSE
TOP MENU
SPACE
VCR
SETUP
CM SKIP
TIMER PROG.
RETURN
123
456
7809
STOP
PLAY
CH
VIDEO/TV
SLOW
PAUSE
.@/:
ABC DEF
GHI JKL MNO
PQRS
REC/OTR
REC MONITOR
MENU/LIST
CLEAR/C-RESET
SEARCH
MODE
ENTER
DISPLAY
TUV WXYZ
DVD
1
2
3
4
5
Video
DVD-RW
DVD-RW
VR
DVD-RW
DVD-RW
Disc
Edit
Forma t
Finalize
Disc Protect OFF ON
Yes No
Are you sure?
Yes No
Setup Menu
Disc
Edit
Forma t
Finalize
Disc Protect OFF ON
Disc
Edit
Forma t
Finalize
Disc Protect OFF ON
Yes No
58%
Formatting
100%
Formatting
Loading...